Community hub
Recent from talks
Knowledge base stats:
Talk channels stats:
Members stats:
Metalorganic vapour-phase epitaxy
Metalorganic vapour-phase epitaxy (MOVPE), also known as organometallic vapour-phase epitaxy (OMVPE) or metalorganic chemical vapour deposition (MOCVD), is a chemical vapour deposition method used to produce single- or polycrystalline thin films. It is a process for growing crystalline layers to create complex semiconductor multilayer structures. In contrast to molecular-beam epitaxy (MBE), the growth of crystals is by chemical reaction and not physical deposition. This takes place not in vacuum, but from the gas phase at moderate pressures (10 to 760 Torr). As such, this technique is preferred for the formation of devices incorporating thermodynamically metastable alloys,[citation needed] and it has become a major process in the manufacture of optoelectronics, such as light-emitting diodes, its most widespread application. It was first demonstrated in 1967 at North American Aviation (later Rockwell International) Autonetics Division in Anaheim CA by Harold M. Manasevit.
In MOCVD ultrapure precursor gases are injected into a reactor, usually with a non-reactive carrier gas. For a III-V semiconductor, a metalorganic could be used as the group III precursor and a hydride for the group V precursor. For example, indium phosphide can be grown with trimethylindium ((CH3)3In) and phosphine (PH3) precursors.
As the precursors approach the semiconductor wafer, they undergo pyrolysis and the subspecies absorb onto the semiconductor wafer surface. Surface reaction of the precursor subspecies results in the incorporation of elements into a new epitaxial layer of the semiconductor crystal lattice. In the mass-transport-limited growth regime in which MOCVD reactors typically operate, growth is driven by supersaturation of chemical species in the vapor phase. MOCVD can grow films containing combinations of group III and group V, group II and group VI, group IV.
Required pyrolysis temperature increases with increasing chemical bond strength of the precursor. The more carbon atoms are attached to the central metal atom, the weaker the bond. The diffusion of atoms on the substrate surface is affected by atomic steps on the surface.
The vapor pressure of the group III metal organic source is an important control parameter for MOCVD growth, since it determines the growth rate in the mass-transport-limited regime.
In the metal organic chemical vapor deposition (MOCVD) technique, reactant gases are combined at elevated temperatures in the reactor to cause a chemical interaction, resulting in the deposition of materials on the substrate.
A reactor is a chamber made of a material that does not react with the chemicals being used. It must also withstand high temperatures. This chamber is composed by reactor walls, liner, a susceptor, gas injection units, and temperature control units. Usually, the reactor walls are made from stainless steel or quartz. Ceramic or special glasses, such as quartz, are often used as the liner in the reactor chamber between the reactor wall and the susceptor. To prevent overheating, cooling water must be flowing through the channels within the reactor walls. A substrate sits on a susceptor which is at a controlled temperature. The susceptor is made from a material resistant to the temperature and metalorganic compounds used, often it is machined from graphite. For growing nitrides and related materials, a special coating, typically of silicon nitride or tantalum carbide, on the graphite susceptor is necessary to prevent corrosion by ammonia (NH3) gas.
One type of reactor used to carry out MOCVD is a cold-wall reactor. In a cold-wall reactor, the substrate is supported by a pedestal, which also acts as a susceptor. The pedestal/susceptor is the primary origin of heat energy in the reaction chamber. Only the susceptor is heated, so gases do not react before they reach the hot wafer surface. The pedestal/susceptor is made of a radiation-absorbing material such as carbon. In contrast, the walls of the reaction chamber in a cold-wall reactor are typically made of quartz which is largely transparent to the electromagnetic radiation. The reaction chamber walls in a cold-wall reactor, however, may be indirectly heated by heat radiating from the hot pedestal/susceptor, but will remain cooler than the pedestal/susceptor and the substrate the pedestal/susceptor supports.
Hub AI
Metalorganic vapour-phase epitaxy AI simulator
(@Metalorganic vapour-phase epitaxy_simulator)
Metalorganic vapour-phase epitaxy
Metalorganic vapour-phase epitaxy (MOVPE), also known as organometallic vapour-phase epitaxy (OMVPE) or metalorganic chemical vapour deposition (MOCVD), is a chemical vapour deposition method used to produce single- or polycrystalline thin films. It is a process for growing crystalline layers to create complex semiconductor multilayer structures. In contrast to molecular-beam epitaxy (MBE), the growth of crystals is by chemical reaction and not physical deposition. This takes place not in vacuum, but from the gas phase at moderate pressures (10 to 760 Torr). As such, this technique is preferred for the formation of devices incorporating thermodynamically metastable alloys,[citation needed] and it has become a major process in the manufacture of optoelectronics, such as light-emitting diodes, its most widespread application. It was first demonstrated in 1967 at North American Aviation (later Rockwell International) Autonetics Division in Anaheim CA by Harold M. Manasevit.
In MOCVD ultrapure precursor gases are injected into a reactor, usually with a non-reactive carrier gas. For a III-V semiconductor, a metalorganic could be used as the group III precursor and a hydride for the group V precursor. For example, indium phosphide can be grown with trimethylindium ((CH3)3In) and phosphine (PH3) precursors.
As the precursors approach the semiconductor wafer, they undergo pyrolysis and the subspecies absorb onto the semiconductor wafer surface. Surface reaction of the precursor subspecies results in the incorporation of elements into a new epitaxial layer of the semiconductor crystal lattice. In the mass-transport-limited growth regime in which MOCVD reactors typically operate, growth is driven by supersaturation of chemical species in the vapor phase. MOCVD can grow films containing combinations of group III and group V, group II and group VI, group IV.
Required pyrolysis temperature increases with increasing chemical bond strength of the precursor. The more carbon atoms are attached to the central metal atom, the weaker the bond. The diffusion of atoms on the substrate surface is affected by atomic steps on the surface.
The vapor pressure of the group III metal organic source is an important control parameter for MOCVD growth, since it determines the growth rate in the mass-transport-limited regime.
In the metal organic chemical vapor deposition (MOCVD) technique, reactant gases are combined at elevated temperatures in the reactor to cause a chemical interaction, resulting in the deposition of materials on the substrate.
A reactor is a chamber made of a material that does not react with the chemicals being used. It must also withstand high temperatures. This chamber is composed by reactor walls, liner, a susceptor, gas injection units, and temperature control units. Usually, the reactor walls are made from stainless steel or quartz. Ceramic or special glasses, such as quartz, are often used as the liner in the reactor chamber between the reactor wall and the susceptor. To prevent overheating, cooling water must be flowing through the channels within the reactor walls. A substrate sits on a susceptor which is at a controlled temperature. The susceptor is made from a material resistant to the temperature and metalorganic compounds used, often it is machined from graphite. For growing nitrides and related materials, a special coating, typically of silicon nitride or tantalum carbide, on the graphite susceptor is necessary to prevent corrosion by ammonia (NH3) gas.
One type of reactor used to carry out MOCVD is a cold-wall reactor. In a cold-wall reactor, the substrate is supported by a pedestal, which also acts as a susceptor. The pedestal/susceptor is the primary origin of heat energy in the reaction chamber. Only the susceptor is heated, so gases do not react before they reach the hot wafer surface. The pedestal/susceptor is made of a radiation-absorbing material such as carbon. In contrast, the walls of the reaction chamber in a cold-wall reactor are typically made of quartz which is largely transparent to the electromagnetic radiation. The reaction chamber walls in a cold-wall reactor, however, may be indirectly heated by heat radiating from the hot pedestal/susceptor, but will remain cooler than the pedestal/susceptor and the substrate the pedestal/susceptor supports.