Community hub
Recent from talks
Contribute something to knowledge base
Content stats: 0 posts, 0 articles, 0 media, 0 notes
Members stats: 0 subscribers, 0 contributors, 0 moderators, 0 supporters
Subscribers
Supporters
Contributors
Moderators
Logical block addressing
Logical block addressing (LBA) is a common scheme used for specifying the location of blocks of data stored on computer storage devices, generally secondary storage systems such as hard disk drives. LBA is a particularly simple linear addressing scheme; blocks are located by an integer index, with the first block being LBA 0, the second LBA 1, and so on.
The IDE standard included 22-bit LBA as an option, which was further extended to 28-bit with the release of ATA-1 (1994) and to 48-bit with the release of ATA-6 (2003), whereas the size of entries in on-disk and in-memory data structures holding the address is typically 32 or 64 bits. Most hard disk drives released after 1996 implement logical block addressing.
In logical block addressing, only one number is used to address data, and each linear base address describes a single block.
The LBA scheme replaces earlier schemes which exposed the physical details of the storage device to the software of the operating system. Chief among these was the cylinder-head-sector (CHS) scheme, where blocks were addressed by means of a tuple which defined the cylinder, head, and sector at which they appeared on the hard disk. CHS did not map well to devices other than hard disks (such as tapes and networked storage), and was generally not used for them. CHS was used in early MFM and RLL drives, and both it and its successor, extended cylinder-head-sector (ECHS), were used in the first ATA drives. However, current disk drives use zone bit recording, where the number of sectors per track depends on the track number. Even though the disk drive will report some CHS values as sectors per track (SPT) and heads per cylinder (HPC), they have little to do with the disk drive's true geometry.
LBA was first introduced in 1981 by SASI, the precursor of SCSI, as an abstraction. While the drive controller still addresses data blocks by their CHS address, this information is generally not used by the SCSI device driver, the OS, filesystem code, or any applications (such as databases) that access the "raw" disk. System calls requiring block-level I/O pass LBA definitions to the storage device driver; for simple cases (where one volume maps to one physical drive), this LBA is then passed directly to the drive controller.
In redundant array of independent disks (RAID) devices and storage area networks (SANs) and where logical drives (logical unit numbers, LUNs) are composed via LUN virtualization and aggregation, LBA addressing of individual disk should be translated by a software layer to provide uniform LBA addressing for the entire storage device.
The earlier IDE standard from Western Digital introduced 22-bit LBA; in 1994, the ATA-1 standard allowed for 28 bit addresses in both LBA and CHS modes. The CHS scheme used 16 bits for cylinder, 4 bits for head and 8 bits for sector, counting sectors from 1 to 255. This means the reported number of heads never exceeds 16 (0–15), the number of sectors can be 255 (1–255; though 63 is often the largest used) and the number of cylinders can be as large as 65,536 (0–65535), limiting disk size to 128 GiB (≈137.4 GB), assuming 512 byte sectors. These values can be accessed by issuing the ATA command "Identify Device" (ECh) to the drive.
However, the IBM BIOS implementation defined in the INT 13h disk access routines used quite a different 24-bit scheme for CHS addressing, with 10 bits for cylinder, 8 bits for head, and 6 bits for sector, or 1024 cylinders, 256 heads, and 63 sectors. This INT 13h implementation had pre-dated the ATA standard, as it was introduced when the IBM PC had only floppy disk storage, and when hard disk drives were introduced on the IBM PC/XT, INT 13h interface could not be practically redesigned due to backward compatibility issues. Overlapping ATA CHS mapping with BIOS CHS mapping produced the lowest common denominator of 10:4:6 bits, or 1024 cylinders, 16 heads, and 63 sectors, which gave the practical limit of 1024×16×63 sectors and 528 MB (504 MiB), assuming 512 byte sectors.
Logical block addressing
Logical block addressing (LBA) is a common scheme used for specifying the location of blocks of data stored on computer storage devices, generally secondary storage systems such as hard disk drives. LBA is a particularly simple linear addressing scheme; blocks are located by an integer index, with the first block being LBA 0, the second LBA 1, and so on.
The IDE standard included 22-bit LBA as an option, which was further extended to 28-bit with the release of ATA-1 (1994) and to 48-bit with the release of ATA-6 (2003), whereas the size of entries in on-disk and in-memory data structures holding the address is typically 32 or 64 bits. Most hard disk drives released after 1996 implement logical block addressing.
In logical block addressing, only one number is used to address data, and each linear base address describes a single block.
The LBA scheme replaces earlier schemes which exposed the physical details of the storage device to the software of the operating system. Chief among these was the cylinder-head-sector (CHS) scheme, where blocks were addressed by means of a tuple which defined the cylinder, head, and sector at which they appeared on the hard disk. CHS did not map well to devices other than hard disks (such as tapes and networked storage), and was generally not used for them. CHS was used in early MFM and RLL drives, and both it and its successor, extended cylinder-head-sector (ECHS), were used in the first ATA drives. However, current disk drives use zone bit recording, where the number of sectors per track depends on the track number. Even though the disk drive will report some CHS values as sectors per track (SPT) and heads per cylinder (HPC), they have little to do with the disk drive's true geometry.
LBA was first introduced in 1981 by SASI, the precursor of SCSI, as an abstraction. While the drive controller still addresses data blocks by their CHS address, this information is generally not used by the SCSI device driver, the OS, filesystem code, or any applications (such as databases) that access the "raw" disk. System calls requiring block-level I/O pass LBA definitions to the storage device driver; for simple cases (where one volume maps to one physical drive), this LBA is then passed directly to the drive controller.
In redundant array of independent disks (RAID) devices and storage area networks (SANs) and where logical drives (logical unit numbers, LUNs) are composed via LUN virtualization and aggregation, LBA addressing of individual disk should be translated by a software layer to provide uniform LBA addressing for the entire storage device.
The earlier IDE standard from Western Digital introduced 22-bit LBA; in 1994, the ATA-1 standard allowed for 28 bit addresses in both LBA and CHS modes. The CHS scheme used 16 bits for cylinder, 4 bits for head and 8 bits for sector, counting sectors from 1 to 255. This means the reported number of heads never exceeds 16 (0–15), the number of sectors can be 255 (1–255; though 63 is often the largest used) and the number of cylinders can be as large as 65,536 (0–65535), limiting disk size to 128 GiB (≈137.4 GB), assuming 512 byte sectors. These values can be accessed by issuing the ATA command "Identify Device" (ECh) to the drive.
However, the IBM BIOS implementation defined in the INT 13h disk access routines used quite a different 24-bit scheme for CHS addressing, with 10 bits for cylinder, 8 bits for head, and 6 bits for sector, or 1024 cylinders, 256 heads, and 63 sectors. This INT 13h implementation had pre-dated the ATA standard, as it was introduced when the IBM PC had only floppy disk storage, and when hard disk drives were introduced on the IBM PC/XT, INT 13h interface could not be practically redesigned due to backward compatibility issues. Overlapping ATA CHS mapping with BIOS CHS mapping produced the lowest common denominator of 10:4:6 bits, or 1024 cylinders, 16 heads, and 63 sectors, which gave the practical limit of 1024×16×63 sectors and 528 MB (504 MiB), assuming 512 byte sectors.