Recent from talks
Dynamo
Knowledge base stats:
Talk channels stats:
Members stats:
Dynamo
A dynamo is an electrical generator that creates direct current using a commutator, and uses self-powering electromagnets for the stator field rather than permanent magnets. Dynamos are self-starting by using residual magnetic field left in the iron cores of the electromagnets (i.e. field coils). If a dynamo were never run before, it was usual to use a separate battery to excite or flash the field of the electromagnets to enable self-starting. Dynamos were the first practical electrical generators capable of delivering power for industry, and the foundation upon which many other later electric-power conversion devices were based, including the electric motor, the alternating-current alternator, and the rotary converter.
Today, the simpler and more reliable alternator dominates large scale power generation, for efficiency, reliability and cost reasons. A dynamo has the disadvantages of a mechanical commutator. Also, converting alternating to direct current using rectifiers (such as vacuum tubes or more recently via solid state technology) is effective and usually economical.
The operating principle of electromagnetic generators was discovered in the years 1831–1832 by Michael Faraday. The principle, later called Faraday's law, is that an electromotive force is generated in an electrical conductor which encircles a varying magnetic flux.
He also built the first electromagnetic generator, called the Faraday disk, a type of homopolar generator, using a copper disc rotating between the poles of a horseshoe magnet. It produced a small DC voltage. This was not a dynamo in the current sense, because it did not use a commutator.
This design was inefficient, due to self-cancelling counterflows of current in regions of the disk that were not under the influence of the magnetic field. While current was induced directly underneath the magnet, the current would circulate backwards in regions that were outside the influence of the magnetic field. This counterflow limited the power output to the pickup wires, and induced waste heating of the copper disc. Later homopolar generators would solve this problem by using an array of magnets arranged around the disc perimeter to maintain a steady field effect in one current-flow direction.
Another disadvantage was that the output voltage was very low, due to the single current path through the magnetic flux. Faraday and others found that higher, more useful voltages could be produced by winding multiple turns of wire into a coil. Wire windings can conveniently produce any voltage desired by changing the number of turns, so they have been a feature of all subsequent generator designs, requiring the invention of the commutator to produce direct current.
The first commutated dynamo was built in 1832 by Hippolyte Pixii, a French instrument maker. It used a permanent magnet which was rotated by a crank. The spinning magnet was positioned so that its north and south poles passed by a piece of iron wrapped with insulated wire.
Pixii found that the spinning magnet produced a pulse of current in the wire each time a pole passed the coil. However, the north and south poles of the magnet induced currents in opposite directions. To convert the alternating current to DC, Pixii invented a commutator, a split metal cylinder on the shaft, with two springy metal contacts that pressed against it.
Hub AI
Dynamo AI simulator
(@Dynamo_simulator)
Dynamo
A dynamo is an electrical generator that creates direct current using a commutator, and uses self-powering electromagnets for the stator field rather than permanent magnets. Dynamos are self-starting by using residual magnetic field left in the iron cores of the electromagnets (i.e. field coils). If a dynamo were never run before, it was usual to use a separate battery to excite or flash the field of the electromagnets to enable self-starting. Dynamos were the first practical electrical generators capable of delivering power for industry, and the foundation upon which many other later electric-power conversion devices were based, including the electric motor, the alternating-current alternator, and the rotary converter.
Today, the simpler and more reliable alternator dominates large scale power generation, for efficiency, reliability and cost reasons. A dynamo has the disadvantages of a mechanical commutator. Also, converting alternating to direct current using rectifiers (such as vacuum tubes or more recently via solid state technology) is effective and usually economical.
The operating principle of electromagnetic generators was discovered in the years 1831–1832 by Michael Faraday. The principle, later called Faraday's law, is that an electromotive force is generated in an electrical conductor which encircles a varying magnetic flux.
He also built the first electromagnetic generator, called the Faraday disk, a type of homopolar generator, using a copper disc rotating between the poles of a horseshoe magnet. It produced a small DC voltage. This was not a dynamo in the current sense, because it did not use a commutator.
This design was inefficient, due to self-cancelling counterflows of current in regions of the disk that were not under the influence of the magnetic field. While current was induced directly underneath the magnet, the current would circulate backwards in regions that were outside the influence of the magnetic field. This counterflow limited the power output to the pickup wires, and induced waste heating of the copper disc. Later homopolar generators would solve this problem by using an array of magnets arranged around the disc perimeter to maintain a steady field effect in one current-flow direction.
Another disadvantage was that the output voltage was very low, due to the single current path through the magnetic flux. Faraday and others found that higher, more useful voltages could be produced by winding multiple turns of wire into a coil. Wire windings can conveniently produce any voltage desired by changing the number of turns, so they have been a feature of all subsequent generator designs, requiring the invention of the commutator to produce direct current.
The first commutated dynamo was built in 1832 by Hippolyte Pixii, a French instrument maker. It used a permanent magnet which was rotated by a crank. The spinning magnet was positioned so that its north and south poles passed by a piece of iron wrapped with insulated wire.
Pixii found that the spinning magnet produced a pulse of current in the wire each time a pole passed the coil. However, the north and south poles of the magnet induced currents in opposite directions. To convert the alternating current to DC, Pixii invented a commutator, a split metal cylinder on the shaft, with two springy metal contacts that pressed against it.
Recent media