Community hub
Recent from talks
Contribute something to knowledge base
Content stats: 0 posts, 0 articles, 0 media, 0 notes
Members stats: 0 subscribers, 0 contributors, 0 moderators, 0 supporters
Subscribers
Supporters
Contributors
Moderators
Signal strength and readability report
A signal strength and readability report is a standardized format for reporting the strength of the radio signal and the readability (quality) of the radiotelephone (voice) or radiotelegraph (Morse code) signal transmitted by another station as received at the reporting station's location and by their radio station equipment. These report formats are usually designed for only one communications mode or the other, although a few are used for both telegraph and voice communications. All but one of these signal report formats involve the transmission of numbers.
As the earliest radio communication used Morse code, all radio signal reporting formats until about the 1920s were for radiotelegraph, and the early voice radio signal report formats were based on the telegraph report formats.[citation needed]
The QSA code and QRK code are interrelated and complementary signal reporting codes for use in wireless telegraphy (Morse code). They replaced the earlier QSJ code.
Currently, the QSA and QRK codes are officially defined in the ITU Radio Regulations 1990, Appendix 13: Miscellaneous Abbreviations and Signals to Be Used in Radiotelegraphy Communications Except in the Maritime Mobile Service. They are also described identically in ACP131(F),:
Amateur radio users in the U.S. and Canada have used the R-S-T system since 1934. This system was developed by amateur radio operator Arthur W. Braaten, W2BSR. It reports the readability on a scale of 1 to 5, the signal strength on a scale of 1 to 9, and the tone of the Morse code continuous wave signal on a scale of 1 to 9. During amateur radio contests, where the rate of new contacts is paramount, contest participants often give a perfect signal report of 599 even when the signal is lower quality, because always providing the same signal format enables them to send Morse code with less thought and thus increased speed.[citation needed]
SINPO is an acronym for Signal, Interference, Noise, Propagation, and Overall, which was developed by the CCIR in 1951 (as C.C.I.R. Recommendation No. 251) for use in radiotelegraphy, and the standard is contained in Recommendation ITU-R Sm.1135, SINPO and SINPFEMO codes. This format is most notably used by the BBC for receiving signal reports on postcards mailed from listeners, even though that same standard specifies that the SINPFEMO code should be used for radiotelephony transmissions. SINPO is the official radiotelegraph signal reporting codes for international civil aviation and ITU-R.
Amateur radio operators use the R-S-T system to describe voice transmissions, dropping the last digit (Tone report) because there is no continuous wave tone to report on.
An extension of SINPO code, for use in radiotelephony (voice over radio) communications, SINPFEMO is an acronym for Signal, Interference, Noise, Propagation, Frequency of Fading, Depth, Modulation, and Overall.
Signal strength and readability report
A signal strength and readability report is a standardized format for reporting the strength of the radio signal and the readability (quality) of the radiotelephone (voice) or radiotelegraph (Morse code) signal transmitted by another station as received at the reporting station's location and by their radio station equipment. These report formats are usually designed for only one communications mode or the other, although a few are used for both telegraph and voice communications. All but one of these signal report formats involve the transmission of numbers.
As the earliest radio communication used Morse code, all radio signal reporting formats until about the 1920s were for radiotelegraph, and the early voice radio signal report formats were based on the telegraph report formats.[citation needed]
The QSA code and QRK code are interrelated and complementary signal reporting codes for use in wireless telegraphy (Morse code). They replaced the earlier QSJ code.
Currently, the QSA and QRK codes are officially defined in the ITU Radio Regulations 1990, Appendix 13: Miscellaneous Abbreviations and Signals to Be Used in Radiotelegraphy Communications Except in the Maritime Mobile Service. They are also described identically in ACP131(F),:
Amateur radio users in the U.S. and Canada have used the R-S-T system since 1934. This system was developed by amateur radio operator Arthur W. Braaten, W2BSR. It reports the readability on a scale of 1 to 5, the signal strength on a scale of 1 to 9, and the tone of the Morse code continuous wave signal on a scale of 1 to 9. During amateur radio contests, where the rate of new contacts is paramount, contest participants often give a perfect signal report of 599 even when the signal is lower quality, because always providing the same signal format enables them to send Morse code with less thought and thus increased speed.[citation needed]
SINPO is an acronym for Signal, Interference, Noise, Propagation, and Overall, which was developed by the CCIR in 1951 (as C.C.I.R. Recommendation No. 251) for use in radiotelegraphy, and the standard is contained in Recommendation ITU-R Sm.1135, SINPO and SINPFEMO codes. This format is most notably used by the BBC for receiving signal reports on postcards mailed from listeners, even though that same standard specifies that the SINPFEMO code should be used for radiotelephony transmissions. SINPO is the official radiotelegraph signal reporting codes for international civil aviation and ITU-R.
Amateur radio operators use the R-S-T system to describe voice transmissions, dropping the last digit (Tone report) because there is no continuous wave tone to report on.
An extension of SINPO code, for use in radiotelephony (voice over radio) communications, SINPFEMO is an acronym for Signal, Interference, Noise, Propagation, Frequency of Fading, Depth, Modulation, and Overall.