Hubbry Logo
Granville Gee Bee Model Z Super SportsterGranville Gee Bee Model Z Super SportsterMain
Open search
Granville Gee Bee Model Z Super Sportster
Community hub
Granville Gee Bee Model Z Super Sportster
logo
8 pages, 0 posts
0 subscribers
Be the first to start a discussion here.
Be the first to start a discussion here.
Granville Gee Bee Model Z Super Sportster
Granville Gee Bee Model Z Super Sportster
Granville Gee Bee Model Z Super Sportster
View on Wikipedia
from Wikipedia

The Granville Gee Bee Model Z was an American racing aircraft that was built, successfully raced and then destroyed in a fatal crash in 1931. It was the first of the Super Sportster aircraft built by Granville Brothers Aircraft of Springfield, Massachusetts, with the sole intent of winning the Thompson Trophy, which it did in September 1931. Its fatal crash that December started the reputation of subsequent Gee Bee aircraft as killers.

Key Information

Design and development

[edit]

Suffering from the effects of the Great Depression, the Granville Brothers decided in July 1931 to build an aircraft to compete in that fall's Thompson Trophy competition at the National Air Races in Cleveland, Ohio. They hoped that a victory in the prestigious race would lead to additional orders for their line of sporting aircraft.[1]

Constructed in less than five weeks at a cost of under $5,000 USD, the Gee Bee (for "Granville Brothers") Model Z, named City of Springfield, was a small, tubby airplane. It was essentially the smallest possible airframe constructed around the most powerful available engine of a suitable size,[2] a supercharged Pratt & Whitney Wasp Junior (R-985) radial engine, producing 535 horsepower (399 kW).[1]

Operational history

[edit]

First flying on August 22, 1931, the Gee Bee Z quickly proved to be tricky to fly, but fulfilled every expectation with regards to its speed. Flown by pilot Lowell Bayles, the Gee Bee Z attained the speed of 267.342 miles per hour (430.245 km/h)[3] at the National Air Races during the Shell Speed Dash qualifying on September 1, then went on to win the Goodyear Trophy race, run over a course of 50 miles (80 km), the next day at an average speed of 205 miles per hour (330 km/h). On September 5, the aircraft's engineer, Bob Hall, flew the Gee Bee Z to victory in the General Tire and Rubber Trophy race, then won again the next day in a free-for-all event.[4]

In the Thompson Trophy Race on September 7, Bayles was triumphant, winning with an average speed of 236.24 miles per hour (380.19 km/h), beating competitors including Jimmy Doolittle, James "Jimmy" Wedell, Ben Howard, Dale Jackson, Bill Ong, Ira Eaker, and Hall, who finished fourth in a Gee Bee Model Y.[4]

Shortly after the Thompson Trophy race, the Gee Bee Z was fitted with a larger, 750-horsepower (560 kW) Wasp Senior radial engine for an attempt at establishing a world speed record for land planes.[1] On its trial speed run, the Gee Bee Z was unofficially clocked at 314 miles per hour (505 km/h). On December 1, 1931, the Gee Bee Z was officially clocked at 281.75 miles per hour (453.43 km/h), surpassing the previous record of 278 miles per hour (447 km/h), but the margin was too small for the record to be officially registered.[4] Four days later, on December 5, 1931, a second speed record attempt was made, but the Gee Bee Z's right wing failed catastrophically, causing the air racer to suddenly roll uncontrollably and crash. Bayles was killed instantly.[2]

The exact cause of the Model Z's crash during the December 1931 speed run has not been determined, and frame-by-frame analysis of the filmed crash has been inconclusive. One theory is the fuel tank cap retaining clip failed, the loose cap hit the windscreen and struck the pilot, incapacitating him. The sudden upset in pitch caused uncontrolled flutter in the right aileron, and the right wing failed from the sudden high-vibration stress.[5][4] Subsequent tests of reproduction Gee Bees have shown the aircraft was susceptible to aerodynamic flutter at high speeds.[1] The 1932 R-1 and its sister ship, the R-2, were the successors to the previous year's Thompson Trophy-winning Model Z.

Legacy

[edit]

Film of the crash of the Gee Bee Z has become some of the most well known footage from the era of air racing. The crash also helped to establish the reputation of Gee Bee racing aircraft as killers.[1] The Super Sportster design was incorporated into the Gee Bee Model R for the 1932 air race season.[6]

Two reproductions of the Gee Bee Z have been constructed. One faithful reproduction of the original aircraft was built by Jeff Eicher and Kevin Kimball of Mount Dora, Florida, and is housed in the Fantasy of Flight museum in Lakeland, Florida.[1] The other reproduction was constructed by Bill Turner in 1978, and features extended wings and fuselage for improved flight characteristics. Turner's reproduction appeared in 1991 as both a static and flying prop in the Disney film The Rocketeer, and is now on display at the Museum of Flight in Tukwila, Washington.[3]

Specifications (Gee Bee Model Z Super Sportster)

[edit]

Data from [4][7]

General characteristics

  • Crew: 1 (pilot)
  • Length: 15 ft 1 in (4.60 m)
  • Wingspan: 23 ft 6 in (7.16 m)
  • Height: 7 ft (2.1 m)
  • Wing area: 75 sq ft (7.0 m2)
  • Airfoil: M-6
  • Empty weight: 1,400 lb (635 kg)
  • Gross weight: 2,280 lb (1,034 kg)
  • Fuel capacity: 103 US gallons (390 L; 86 imp gal)
  • Powerplant: 1 × Pratt & Whitney Wasp Junior radial, 535 hp (399 kW) supercharged
  • Propellers: 2-bladed Curtiss Reed fixed pitch, 8 ft 2 in (2.49 m) diameter

Performance

  • Maximum speed: 232.314 kn (267.342 mph, 430.245 km/h)
  • Cruise speed: 200 kn (230 mph, 370 km/h)
  • Range: 780 nmi (900 mi, 1,400 km)
[edit]

Kermit Weeks, founder of Fantasy of Flight, used a Gee Bee Model Z as his main character "Zee" in a series of children's books set around the interwar period. [8]

A modified, flying replica of the Gee Bee Model Z appeared in several scenes in the 1991 Walt Disney feature film, The Rocketeer.

See also

[edit]

Related development

Aircraft of comparable role, configuration, and era

References

[edit]
[edit]
Revisions and contributorsEdit on WikipediaRead on Wikipedia

Granville Gee Bee Model Z Super Sportster

View on Grokipedia
from Grokipedia
The Granville Gee Bee Model Z Super Sportster was a pioneering American constructed in 1931 by the Company in , renowned for its revolutionary and compact design that prioritized extreme speed over stability. Featuring the smallest feasible enveloping a supercharged nine-cylinder rated at 535 horsepower, the single-seat, low-wing achieved remarkable velocities but was infamous for its tricky handling characteristics due to its short and high . Designed by aeronautical engineer Robert Leicester Hall and backed by investor-pilot Lowell Bayles, the sole prototype—registered NR77V and christened City of Springfield—made its on August 22, 1931, just weeks before competing in the . Bayles piloted the aircraft to victory in the prestigious Thompson Trophy Race on September 7, 1931, completing the pylon course at an average speed of 236.2 miles per hour (380.2 kilometers per hour), which also established a new international landplane for aircraft under 1,500 pounds empty weight. This triumph highlighted the Gee Bee's dominance in early , influencing subsequent designs in the series, though its aggressive contributed to the era's high-risk profile for pilots. Following the race, the Model Z underwent an engine upgrade to a larger Wasp radial producing over 700 horsepower, aiming to challenge the landplane . On December 5, 1931, during a record attempt at Wayne County Airport in , , Bayles pushed the into a high-speed dive exceeding 300 miles per hour (483 kilometers per hour) when structural failure occurred—the right wing folded, and the plane plummeted from approximately 150 feet (46 meters), erupting in flames upon impact and claiming Bayles's life. The tragedy underscored the aircraft's engineering limits, yet the Model Z's legacy endures as a symbol of bold innovation in aviation history, with reproductions preserving its form for educational and display purposes.

Development

Granville Brothers Background

The Granville Brothers Aircraft Company was established in 1929 in , by five brothers—Zantford (known as "Grin" or "Granny"), Thomas, Robert, Mark, and Edward Granville—who had previously operated an aircraft repair business in . The brothers, originally from rural , leveraged their mechanical skills honed from post-World War I automotive and aviation work to formalize their operations at the Springfield Airport, converting an abandoned into a workshop with a modest from the Taits brothers, local Springfield businessmen. Initially, the company's focus centered on repair, modification, and the production of affordable sport planes, such as the Model A biplane introduced that same year, which was marketed as an accessible option for private pilots amid a growing but economically strained sector. However, the onset of the in 1929 devastated commercial sales, limiting the Model A to just eight units and forcing the Granvilles to seek alternative revenue streams through high-stakes endeavors. In response to these economic pressures, the brothers pivoted toward custom racing aircraft designed for low-cost construction yet exceptional performance, aiming to win lucrative prizes that could sustain the business and showcase their engineering prowess. Their specific objective was to enter the 1931 in , , with a particular emphasis on capturing the Thompson Trophy—a premier closed-course event offering substantial cash awards—as a strategic tool to attract attention and potential orders for their innovative "Gee Bee" designs. This racer-focused strategy marked a decisive evolution from repair services, culminating in the development of the Model Z, the first of the Super Sportster series of purpose-built racing aircraft.

Design and Construction

Designed by aeronautical engineer Robert Leicester Hall, the Company completed construction of the Model Z Super Sportster in the summer of 1931, assembling the aircraft in under five weeks at a total cost of less than $5,000 by relying heavily on off-the-shelf and donated components from sponsors. This rapid build was driven by the need to prepare for the upcoming , leveraging the brothers' prior experience in modifying existing aircraft to accelerate development. The design featured an extremely short fuselage, often described as resembling a "flying engine," to minimize aerodynamic drag, featuring a supercharged 535 hp Wasp Junior mounted in the nose immediately ahead of the cockpit. The airframe combined a welded tube and tail surfaces with wooden and spars for the , all covered in fabric for a lightweight structure; it included fixed and a deliberately small area to achieve high optimized for speed. Aerodynamic trade-offs were central to the philosophy, incorporating intentional instability in pitch and yaw to enable sharper, quicker turns during pylon racing, while the supercharged was loaned directly from to enhance power output. The aircraft was christened the "Super Sportster" to emphasize its high-speed potential and attract sponsorship, ultimately bearing the name City of Springfield in honor of its primary backer, the local municipality that provided financial and material support.

Operational History

Initial Flights and Races

The Gee Bee Model Z Super Sportster achieved its first flight on August 22, 1931, at Springfield Airport in , piloted by the aircraft's designer, Robert Leicester Hall. This brief test confirmed the aircraft's basic handling characteristics, though it revealed challenges in stability due to its radical design, paving the way for rapid refinements ahead of competition. In preparation for the 1931 National Air Races held in Cleveland, Ohio, the Granville Brothers secured funding through the Springfield Air Racing Association, a group of local investors who purchased shares to support the project, leading to the aircraft being named the "City of Springfield." Constructed in under five weeks at a cost below $5,000, the racer was powered by a loaned radial engine and tested further at nearby Bowles Airport in Agawam before transport to the event. Lowell Bayles, a seasoned pilot who had invested in the venture, was selected to fly it, leveraging the aircraft's compact form to execute exceptionally tight pylon turns during qualifying. On September 7, 1931, Bayles piloted the "City of Springfield" to victory in the Thompson Trophy Race, a grueling 10-lap, 50-mile pylon course that tested both speed and maneuverability. Averaging 236.24 (380.19 kilometers per hour), the win earned a $7,500 prize and established a new U.S. landplane , outpacing competitors like Jimmy Doolittle's modified Super Solution. Earlier in the meet, Bayles had also set a qualifying speed of 267.342 (430.245 kilometers per hour) in the Shell Speed Dash, underscoring the Model Z's dominance. Following the Thompson victory, the Granville team modified the aircraft for upcoming land speed record attempts by replacing the 535-horsepower Wasp Junior with a more powerful 750-horsepower Senior radial engine to boost straight-line performance. These changes, including adaptations to accommodate the larger engine, positioned the Model Z for international record challenges later that year.

Crash and Aftermath

Bayles had made an unofficial attempt on December 1, averaging 281.75 mph over four passes, but official timers were not ready, so it was not ratified. On December 5, 1931, pilot Lowell Bayles took off from Wayne County Airport in , Michigan, aboard the Granville Gee Bee Model Z Super Sportster for an attempt to break the (FAI) world landplane speed record, which stood at 278.48 mph. During the upward leg of the measured kilometer course, timing equipment recorded the aircraft attaining 281.75 mph, surpassing the existing mark and positioning Bayles for a successful average speed over the required two runs. As Bayles executed the pull-up to reverse course for the downward leg, the tail structure suddenly failed under the aerodynamic loads, causing the aircraft to pitch violently upward and disintegrate mid-air. The Super Sportster struck the ground at over 300 mph near a railroad track, erupting into a massive fireball that scattered wreckage over a wide area; Bayles was killed instantly upon impact. The precise cause of the tail failure has never been conclusively determined, though examinations of the wreckage and eyewitness testimonies pointed to a probable induced by excessive g-forces during the maneuver or an undetected manufacturing defect in the . Some analyses suggested a contributing factor may have been a loose that detached at high speed, striking the and momentarily incapacitating Bayles, which exacerbated the control inputs leading to overload. The (NACA) initiated related investigations into the structural dynamics of high-speed monoplanes, citing the incident as a case of destructive wing-aileron flutter that highlighted vulnerabilities in radical racing s. These probes influenced subsequent aerodynamic but did not result in formal modifications for the surviving fleet.

Technical Specifications

Airframe and Dimensions

The Granville Gee Bee Model Z Super Sportster was a single-seat low-wing monoplane built for air racing, with the cockpit designed to accommodate one pilot. The airframe utilized a chrome-moly steel tube fuselage structure covered in fabric for the main body, while the wings employed a spruce wood frame with plywood sheeting and fabric skin to provide strength and a smooth aerodynamic surface. The aircraft was equipped with a fixed tailwheel undercarriage, incorporating 23-inch Goodrich tires on a wheel tread of 71.75 inches for ground operations. Key dimensions of the Model Z emphasized its compact design, which prioritized speed over stability. The overall measured 15 feet, 1 inch (4.597 meters), the was 23 feet, 6 inches (7.163 meters), and the wing area totaled 75 square feet (7.968 square meters). The wings incorporated a 3° angle of incidence and 4.5° dihedral for lift distribution. The empty weight stood at 1,400 pounds (635 kilograms), while the maximum gross weight reached 2,280 pounds (1,034 kilograms). This configuration, particularly the short fuselage, facilitated reduced aerodynamic drag, enabling the aircraft's exceptional in closed-course .

Engine and Performance

The Granville Gee Bee Model Z Super Sportster was powered by a , a 9-cylinder air-cooled supercharged to deliver 535 horsepower (399 kW) at 2,400 rpm. This powerplant, derived from a standard 450-horsepower configuration but tuned for demands, provided the necessary for high-speed in air races. The utilized a two-blade fixed-pitch metal sourced from Curtiss, optimized to absorb the engine's output efficiently during straight-line sprints and pylon turns. Performance capabilities included a maximum speed exceeding 267 (430 kilometers per hour), enabling competitive edges in events like the Thompson Trophy Race where the engine's power contributed to victory. The estimated range was 900 miles (1,450 kilometers), suitable for cross-country positioning flights between race venues.

Legacy

Engineering Influence

The Granville Gee Bee Model Z Super Sportster exemplified an engineering philosophy that prioritized extreme power-to-weight ratios over aerodynamic stability, a radical approach that reshaped the design of pylon racing aircraft. With its compact fuselage housing a supercharged engine producing 535 horsepower in a wooden weighing 1,400 pounds (635 kg) empty, the Model Z achieved a that enabled record speeds exceeding 260 mph in straight-line flight. This emphasis on raw performance, at the expense of due to the short-coupled design placing the center of gravity far aft of the wing, influenced subsequent racers by demonstrating that minimal structural mass could yield competitive advantages in closed-course events. Notably, the French Rafale, which captured the Thompson Trophy at an average speed of 264 mph, adopted similar low-wing configurations with retractable gear and streamlined forms inspired by American racers like the Gee Bee series, adapting the power-focused ethos to European pylon racing demands. Post-crash investigations into the Model Z's fatal 1931 disintegration during a attempt highlighted the inherent risks of short-coupled designs, catalyzing advancements in aviation stress analysis. The accident, in which pilot Lowell Bayles lost control at over 300 mph leading to wing failure, was attributed to a loose fuel cap that struck the pilot, causing incapacitation. This incident, along with other high-speed accidents, contributed to broader (NACA) research in on flutter phenomena to refine predictive models for structural loads in high-speed monoplanes. These findings contributed to improved finite element stress analysis techniques, influencing safer designs in military and civilian by emphasizing balanced moment arms and reinforced wing roots to mitigate vibration-induced failures. The Model Z's innovative drag reduction techniques, particularly its tight NACA-engineered enclosing the , set precedents for aerodynamic efficiency that extended to fighters. The contoured minimized frontal area while directing cooling air through precisely shaped baffles, reducing by up to 20% compared to exposed-cylinder predecessors and enabling the aircraft's sleek barrel-like profile. This approach to integrating powerplants seamlessly into the was emulated in radial-engined pursuits like the , where similar low-drag s allowed sustained high speeds above 400 mph without excessive fuel consumption. By proving the viability of such enclosures in extreme racing conditions, the Gee Bee accelerated the adoption of streamlined nacelles in wartime production, enhancing overall fighter performance margins. Earned the grim moniker "widowmaker" for its unforgiving handling quirks—including a tendency to snap into during high-angle turns and poor recovery—the Model Z underscored the need for specialized pilot training in high-performance . Its neutral stability and high demanded precise control inputs, with even experienced aviators like Bayles noting the constant vigilance required to counter oscillations. The series of fatal crashes involving Gee Bee variants prompted authorities and manufacturers to develop rigorous transition programs, emphasizing simulator-based familiarization with short-coupled dynamics and . This legacy influenced postwar pilot curricula, particularly for jet transitions, by integrating lessons on into standard high-speed handling protocols.

Replicas and Preservation

The first full-scale flying replica of the Granville Gee Bee Model Z Super Sportster was constructed in 1978 by retired U.S. Navy pilot Bill Turner, with technical input from original designers Bob and Ed Granville to ensure fidelity to the 1931 design. This reproduction incorporated modifications for enhanced safety and stability, including a slightly extended and wings compared to the original, which helped mitigate the aircraft's notoriously sensitive handling. Powered by an authentic delivering 535 horsepower, the replica was designed for flight and appeared in airshows, EAA exhibits, and the 1991 film The Rocketeer before being acquired by the in 2003. It remains on static display there in , preserving the aircraft's racing heritage for public education. A second prominent replica was built in the mid-1990s by builders Jeff Eicher and Kevin Kimball, achieving its in June 1996 with Delmar Benjamin at Leesburg International Airport in . Owned by collector and pilot , this highly accurate reproduction is maintained at the museum in , where it serves as a centerpiece for displays and occasional airshow demonstrations. To address the original Model Z's stability challenges, particularly wing flutter at speeds exceeding 240 mph, the replica features modern additions such as external balance weights on the spars, enabling controlled flights over 300 mph while retaining the R-985 engine derated to 450 horsepower for safer operation. This aircraft underscores the design's enduring appeal in history as a benchmark for speed and engineering daring. Efforts to replicate the Model Z have highlighted key challenges in recreating technology with modern constraints, including the difficulty of sourcing authentic materials like Sitka spruce for the wings and doped fabric coverings, which are no longer produced in the same quantities or specifications. Builders like Turner and Eicher/Kimball relied on consultations with surviving Granville family members and archival plans to overcome these hurdles, while integrating subtle aerodynamic tweaks to counteract the original's pitch instability without altering its iconic barrel-like profile. Preservation of these wooden airframes demands rigorous ongoing maintenance, such as humidity-controlled storage, periodic doping renewals, and inspections for rot or , to prevent structural deterioration exacerbated by Florida's climate at or Washington's variable weather at the . As of 2025, no additional full-scale replicas have been reported under construction, with focus remaining on conserving the existing examples through museum stewardship.

References

  1. https://www.museumofflight.org/exhibits-and-events/aircraft/granville-brothers-gee-bee-z-city-springfield
  2. https://airandspace.si.edu/support/wall-of-honor/lowell-r-bayles-gee-bee-pilot
  3. https://www.aahs-online.org/pubs/AeroBios.php?ltr=GRANVILLE%20Bros
  4. https://www.wearethemighty.com/history/gee-bee-racer-widowmaker/
  5. https://www.thisdayinaviation.com/tag/robert-leicester-hall/
  6. https://www.patrickchovanec.com/aviation/gee-bee-model-z-r-1931/
  7. http://www.aviastar.org/gallery/051.html
  8. https://www.fiddlersgreen.net/models/aircraft/GeeBee-Z.html
  9. https://www.thisdayinaviation.com/7-september-1931/
  10. https://springfieldmuseums.org/blog/lowell-r-bayles-spirit-springfield/
  11. https://www.flightsimulator.com/famous-flyer-ii-gee-bee-model-z-super-sportster-and-model-r-2-super-sportster/
  12. https://content.time.com/time/subscriber/article/0,33009,930425,00.html
  13. https://criticalpast.com/video/65675046366_Pursuit-Airplanes_Pilot-Lowell-Bayles_Gee-Bee-Racer-airplane_hits-ground-and-explodes
  14. https://www.nytimes.com/1931/12/06/archives/crash-kills-bayles-at-300mile-speed-dies-in-attempt-for-speed.html
  15. https://motorsportmemorial.org/focus.php?db=a&n=8433
  16. https://asn.flightsafety.org/wikibase/259746
  17. https://ntrs.nasa.gov/api/citations/19760003007/downloads/19760003007.pdf
  18. https://air-racing-history.com/aircraft/GeeBee_Z.html
  19. https://www.thisdayinaviation.com/tag/gee-bee-model-z/
  20. https://www.fantasyofflight.com/collection/aircraft/currently-not-showing-in-museum/golden-age/1931-gee-bee-z/
  21. https://science.howstuffworks.com/transport/flight/classic/granville-brothers-gee-bee-super-sportster-r-1.htm
  22. https://planeandpilotmag.com/grandville-brothers-gee-bee/
  23. http://www.fiddlersgreen.net/models/aircraft/GeeBee-Z.html
  24. https://www.nytimes.com/1936/09/08/archives/french-flier-wins-thompson-trophy-detroyat-makes-record-speed-of.html
  25. https://www.thisdayinaviation.com/tag/granville-brothers-aircraft-company/
  26. https://www.fantasyofflight.com/collection/aircraft/golden-age/1931-gee-bee-z/
  27. https://generalaviationnews.com/2018/08/11/visiting-the-gee-bees-at-fantasy-of-flight/
  28. https://jkeworks.com/hot-rods-of-the-sky-episode-2-the-gee-bee-model-z-part-1-2/
Add your contribution
Related Hubs
User Avatar
No comments yet.