General Electric J79

The General Electric J79 is an axial-flow turbojet engine built for use in a variety of fighter and bomber aircraft and a supersonic cruise missile. The J79 was produced by General Electric Aircraft Engines in the United States, and under license by several other companies worldwide. Among its major uses was the Lockheed F-104 Starfighter, Convair B-58 Hustler, McDonnell Douglas F-4 Phantom II, North American A-5 Vigilante and IAI Kfir.

A commercial version, designated the CJ805, powered the Convair 880, while an aft-turbofan derivative, the CJ805-23, powered the Convair 990 airliners and a single Sud Aviation Caravelle intended to demonstrate to the U.S. market the benefits of a bypass engine over the existing Rolls-Royce Avon turbojet.

In 1959 the gas generator of the J79 was developed as a stationary 10 MW-class (13,000 bhp) free-turbine turboshaft engine for naval power, power generation, and industrial use, called the LM1500. Its first application was in the research hydrofoil USS Plainview.

By the late 1940s, jet engine design had progressed to the point where further progress was limited by the performance of its compressor, in particular the pressure ratio of the compressor had to be increased to reduce the engine fuel consumption. However, the useful operating range of the compressor was limited at that time and centered around its design condition which is at a high compressor speed for take-off or cruise. If designed for high efficiency at high speeds it was very inefficient and prone to stall at low speeds.

In 1944 the National Advisory Committee for Aeronautics had tested a theory for "Extending the useful operating range of axial-flow compressors by use of adjustable stator blades" by running an eight-stage axial compressor with pressure ratio 3.42:1 and adjustable blade angles. Considerable improvement in efficiencies were obtained at compressor speeds appreciably below the design speed.

Departures of velocity from the design condition are most noticeable in the first stages at low rpm and become more so as the design pressure ratio is increased leading to blade stall and compressor surging as happened with the Rolls-Royce Avon compressor, with design pressure ratio of 6.3:1 in 1949. In 1947 Geoff Wilde, a Rolls-Royce compressor designer, had applied for a patent "Axial flow compressor regulation" "to provide a compressor with a wide speed-range of operation". An experimental 12-stage compressor was built with the inlet guide vanes and first four rows of stator blades adjustable to lower the air incidence angles while running at low speed. It was very effective in overcoming the stall and surge. However, a simpler mechanical-design solution (variable inlet guide vanes and bleed) had already been shown to work with the required design pressure ratio so variable stators were not used in a Rolls-Royce engine until the 1980s (IAE V2500).

By 1950 General Electric was focusing on supersonic engines with variable stators as a result of design studies which compared them with dual-rotor types. Based on their past experience at that time, and estimation of the development effort required to prove new technologies, variable stators promised the best way of designing the compressor for the high required pressure ratio of 12:1. This pressure ratio was needed to achieve the supersonic performance, subsonic cruise performance and low weight necessary for future supersonic aircraft.

In 1951, a General Electric team led by Gerhard Neumann, at that time in charge of engine development testing, was given funding to build a test compressor with variable stators. In addition, the Aircraft Gas Turbine Division lead, C.W. 'Jim' LaPierre, formed two teams to do design studies for an engine that could run for extended periods at Mach 2.0 while still giving good fuel economy while cruising at Mach 0.9. Neumann led a team using a variable stator configuration, while Chapman Walker led a parallel effort using two-spools. After a years study the engine with variable stators was chosen as it was lighter, simpler and had a smaller diameter. A demonstrator engine with variable stators, the GOL-1590, predecessor to the J79 was built. At the same time a new engine, the X-24A, was designed for a supersonic aircraft and selected by the Air Force. Development of the new engine was supported by running the GOL-1590 demonstrator engine.