Hubbry Logo
Management Data Input/OutputManagement Data Input/OutputMain
Open search
Management Data Input/Output
Community hub
Management Data Input/Output
logo
7 pages, 0 posts
0 subscribers
Be the first to start a discussion here.
Be the first to start a discussion here.
Management Data Input/Output
Management Data Input/Output
Management Data Input/Output
View on Wikipedia
from Wikipedia

Management Data Input/Output (MDIO), also known as Serial Management Interface (SMI) or Media Independent Interface Management (MIIM), is a serial bus defined for the Ethernet family of IEEE 802.3 standards for the Media Independent Interface, or MII. The MII connects media access control (MAC) devices with Ethernet physical layer (PHY) circuits. The MAC device controlling the MDIO is called the Station Management Entity (SME).

Relationship to MII

[edit]

MII has two signal interfaces:

  • A Data interface to the Ethernet MAC, for sending and receiving Ethernet frame data.
  • A PHY management interface, MDIO, used to read and write the control and status registers of the PHY in order to configure each PHY before operation, and to monitor link status during operation.

Electrical specification

[edit]

The MDIO interface is implemented by two signals:

  • MDIO Interface Clock (MDC): clock driven by the MAC device to the PHY.
  • MDIO data: bidirectional, the PHY drives it to provide register data at the end of a read operation.

The bus only supports a single MAC as the master, and can have up to 32 PHY slaves.

The MDC can be periodic, with a minimum period of 400 ns, which corresponds to a maximum frequency of 2.5 MHz. Newer chips, however, allow faster accesses. For example, the DP83640 supports a 25 MHz maximum clock rate for MDC.

The MDIO requires a specific pull-up resistor of 1.5 kΩ to 10 kΩ, taking into account the total worst-case leakage current of 32 PHYs and one MAC.

Bus timing (clause 22)

[edit]

Before a register access, PHY devices generally require a preamble of 32 ones to be sent by the MAC on the MDIO line. The access consists of 16 control bits, followed by 16 data bits. The control bits consist of 2 start bits, 2 access type bits (read or write), the PHY address (5 bits), the register address (5 bits), and 2 "turnaround" bits.

During a write command, the MAC provides address and data. For a read command, the PHY takes over the MDIO line during the turnaround bit times, supplies the MAC with the register data requested, then releases the MDIO line.

MIIM write and read access

When the MAC drives the MDIO line, it has to guarantee a stable value 10 ns (setup time) before the rising edge of the clock MDC. Further, MDIO has to remain stable 10 ns (hold time) after the rising edge of MDC.

When the PHY drives the MDIO line, the PHY has to provide the MDIO signal between 0 and 300 ns after the rising edge of the clock.[1] Hence, with a minimum clock period of 400 ns (2.5 MHz maximum clock rate) the MAC can safely sample MDIO during the second half of the low cycle of the clock.

MDIO Packet Format (clause 22)

[edit]
MDIO Packet Format
Bit: 0 1 2 3 4 8 9 13 14 15 16 31
0 PRE_32
32 ST OP PA5 RA5 TA D16

PRE_32

The first field in the MDIO header is the Preamble. During the preamble, the MAC sends 32 bits, all '1', on the MDIO line.

ST

The Start field consists of 2 bits and always contains the combination '01'.

OP

The Opcode consists of 2 bits. There are two possible opcodes, read '10' or write '01'.

PA5

5 bits, PHY address.

RA5

The Register Address field indicates the register to be written to or read from. It is 5 bits long.

TA

The turn-around field is 2 bits long. When data is being written to the PHY, the MAC writes '10' to the MDIO line. When data is being read, the MAC releases the MDIO line.

D16

16 bits, data. This can be sent by either the SME or the PHY, depending on the value of the OP field.

Z

Tristate MDIO.

Commands

[edit]

IEEE 802.3 Part 3[1] use different opcodes and start sequences. Opcodes 00(set address) and 11(read)/01(write)/10(read increment) are used as two serial transactions to read and write registers.

References

[edit]
[edit]
Revisions and contributorsEdit on WikipediaRead on Wikipedia

Management Data Input/Output

View on Grokipedia
from Grokipedia
Management Data Input/Output (MDIO) is a two-wire serial bus protocol defined in the IEEE 802.3 Ethernet standard to enable management of physical layer (PHY) devices by a station management entity, typically a media access controller (MAC). It facilitates reading and writing to PHY registers for configuration, status monitoring, and control, using a clock signal (MDC) up to 2.5 MHz and a bidirectional data line (MDIO). Originally specified in Clause 22 of IEEE 802.3 for speeds up to 1 Gbps, MDIO supports up to 32 PHY devices, each with 32 accessible 16-bit registers addressed via 5-bit PHY and register addresses. The protocol operates through framed transactions: a 32-bit preamble of logic 1s for synchronization, followed by start bits (01), operation code (01 for write, 10 for read), address fields, a 2-bit turnaround for bus contention avoidance, 16-bit data, and idle state. This clause emphasizes 5V-tolerant electrical signaling and basic management functions like link status, speed, and duplex mode detection. For higher-speed Ethernet, Clause 45 extends MDIO capabilities, introduced in IEEE 802.3ae for 10 Gbps and beyond, supporting up to 65,536 registers per device through 16-bit addressing and two-phase access cycles (address set followed by read/write). It introduces MDIO Manageable Devices (MMDs) for modular register organization, lower voltage operation down to 1.2 V, and advanced features such as end-to-end fault indication and multiple loopback modes, while maintaining backward compatibility with Clause 22 via register mapping. These extensions ensure MDIO's relevance in modern Ethernet systems, including industrial and automotive applications where precise PHY configuration is essential for reliability.

Overview

Definition and Purpose

Management Data Input/Output (MDIO) is a bidirectional serial bus protocol defined in the IEEE 802.3 standard for Ethernet networks, specifically within the Media Independent Interface (MII) management framework. It enables communication between the Media Access Control (MAC) sublayer, which acts as the Station Management Entity (SME), and physical layer (PHY) devices. The primary purpose of MDIO is to facilitate the configuration of PHY registers and the retrieval of operational status information, such as link status, negotiation speed, and duplex mode, allowing network administrators to monitor and adjust Ethernet transceivers dynamically. This protocol supports remote management capabilities, enabling these operations without disrupting ongoing data traffic on the primary Ethernet data paths. MDIO is also referred to as the Serial Management Interface (SMI) or Media Independent Interface Management (MIIM). In its basic topology, a single MAC can connect to up to 32 PHY devices on a shared bus, using a 5-bit PHY address to distinguish each device.

Historical Development and Standards

The Management Data Input/Output (MDIO) interface was initially defined in Clause 22 of IEEE 802.3u-1995 to provide serial management capabilities for Fast Ethernet (100 Mbps) physical layer (PHY) devices, allowing access to up to 32 registers across 32 PHYs via a two-wire bus. This specification established the foundational frame format and timing for low-speed Ethernet management, with the management data clock (MDC) operating at frequencies up to 2.5 MHz. With the advent of higher-speed Ethernet, Clause 45 was introduced in IEEE Std 802.3ae-2002 to extend MDIO functionality for 10 Gigabit Ethernet, accommodating more complex PHY architectures that required access to additional registers and multi-device support. This expansion addressed limitations in Clause 22 by implementing a two-stage addressing scheme—using device type (ST) codes and port addresses—to manage up to 65,536 registers per device, while maintaining compatibility with the existing electrical interface. Key consolidations and amendments followed, including IEEE Std 802.3-2018, which integrated prior revisions to support Ethernet speeds up to 400 Gb/s and refined MDIO register mappings for diverse PHY types. The IEEE Std 802.3-2022 further advanced the standard with amendments for automotive Ethernet (e.g., multi-gigabit over unshielded twisted pair) and Power over Ethernet enhancements, adding MDIO-accessible parameters for power management and vehicle-specific diagnostics. The IEEE 802.3df-2024 amendment added physical layer specifications and management parameters for 800 Gb/s Ethernet, utilizing Clause 45 for extended register access in high-speed applications. As of the IEEE P802.3dm draft in July 2025, Clause 45 includes updates such as new registers for BASE-T1 PHYs to support emerging automotive and industrial applications. Adoption milestones reflect Ethernet's growth: Clause 22 achieved widespread implementation in 10/100 Mbps networks by the mid-2000s, enabling standardized PHY configuration in enterprise and consumer devices. Clause 45 became mandatory for 10 Gb/s and higher PHYs starting with the 2002 standard, gaining broad industry traction by 2006 as 10G Ethernet deployments accelerated in data centers and backbone infrastructure. This transition from Clause 22's straightforward 2.5 MHz bus to Clause 45's extensible framework has been essential for scaling management in modern, high-density Ethernet ecosystems.

Interface Fundamentals

Relationship to Media Independent Interface

The Media Independent Interface (MII), defined in IEEE 802.3 Clause 22, establishes a standardized connection between the Media Access Control (MAC) sublayer and the Physical Layer (PHY) entity, comprising both data transmission paths and a dedicated management interface. The data interface consists of transmit (TX) and receive (RX) signal pairs that handle Ethernet frame transfer at speeds of 10 Mb/s or 100 Mb/s using four-bit wide nibbles, while the management interface employs the Management Data Input/Output (MDIO) serial bus for control and monitoring functions. This separation ensures that management operations do not interfere with the ongoing data flow across the TX/RX paths. MDIO serves as the management sublayer of the MII, enabling the Station Management entity (typically the MAC) to access the PHY's Management Information Base (MIB) through a set of standardized registers for configuration, status reporting, and diagnostics. As a two-wire serial bus—comprising the bidirectional MDIO data line and the Management Data Clock (MDC)—it allows the MAC to act as the master device, initiating read/write operations to up to 32 slave PHY devices addressed via a 5-bit PHY address (0-31). This master-slave architecture supports independent management transactions, such as querying link status or enabling loopback modes, without disrupting frame transmission. The MDIO interface has evolved alongside higher-speed variants of the MII while preserving its core management role. In the Gigabit Media Independent Interface (GMII), Reduced Gigabit Media Independent Interface (RGMII), and 10 Gigabit Media Independent Interface (XGMII), MDIO continues to provide register access for PHY control, extended through mechanisms like Clause 45 to accommodate expanded register sets for multi-gigabit operations. These adaptations maintain compatibility with the original MII management framework, supporting features such as auto-negotiation for speed and duplex mode selection. This integration offers key benefits, including support for hot-swappable PHY devices through non-intrusive register accesses and dynamic reconfiguration during operation, which enhances system flexibility and reliability in Ethernet networks. By decoupling management from data paths, MDIO facilitates modular designs where PHYs can be interchanged or adjusted without halting traffic, a foundational aspect of media-independent Ethernet implementations.

Electrical Characteristics

The Management Data Input/Output (MDIO) interface utilizes two primary signals at the physical layer: the Management Data Clock (MDC), which is driven as an output by the station management entity (typically the media access control sublayer or MAC), and the bidirectional MDIO line for data transfer. The MDC provides a clock reference for synchronizing MDIO operations, with Clause 22 specifying a maximum frequency of 2.5 MHz. Some implementations support higher frequencies up to 25 MHz. The MDIO signal employs an open-drain configuration with three-state drivers, allowing multiple physical layer devices (PHYs) to share the bus; during MAC transmission, PHYs enter a high-impedance (tristate) state to avoid contention. Voltage levels for the MDIO interface are designed for compatibility with standard logic families. In Clause 22, the interface aligns with TTL/CMOS levels, supporting supplies from 0 V to 5 V and commonly operating at 3.3 V, with output high voltage (V_OH) ≥ 2.4 V at -4 mA and output low voltage (V_OL) ≤ 0.4 V at 4 mA. Clause 45 extends support to low-voltage CMOS (LVCMOS) processes, targeting a nominal 1.2 V supply, where V_OH ranges from 1.0 V to 1.5 V at -100 µA (with drive up to -4 mA), V_OL from -0.3 V to 0.2 V at 100 µA (up to 4 mA), input high voltage (V_IH) from 0.84 V to 1.5 V, and input low voltage (V_IL) from -0.3 V to 0.36 V. These specifications ensure interoperability across voltage domains, often requiring level translation for mixed Clause 22 and 45 environments. The MDIO line incorporates a pull-up resistor to V_CC (or V_DD) to establish a default high state, sized between 1.5 kΩ and 10 kΩ to accommodate leakage currents from up to 32 PHYs plus the MAC; a common value is 4.7 kΩ or 1.5 kΩ ±5% for Clause 22 compliance. The MAC actively drives MDIO low during its transmit phase, while PHYs rely on the pull-up for idle states. Drive strength is specified at a minimum of 4 mA sink/source capability to maintain signal integrity across the bus. Maximum bus capacitance is limited to 470 pF total in Clause 22 for a fully loaded bus with 32 PHYs, with input capacitance per device ≤ 10 pF; Clause 45 maintains similar loading constraints at ≤ 470 pF. Due to its serial, open-drain architecture and low-frequency operation, the MDIO interface consumes minimal power, typically in the microamp range during idle states, making it suitable for integration in power-over-Ethernet (PoE) devices where management overhead must not significantly impact overall budget.

Clause 22 Specification

Bus Timing Requirements

The bus timing requirements for Clause 22 of the IEEE 802.3 standard ensure reliable serial communication over the MDIO interface by defining precise clocking and signal stability parameters. The Management Data Clock (MDC) operates with a minimum period of 400 ns, corresponding to a maximum frequency of 2.5 MHz, allowing sufficient time for signal settling across multi-drop buses. The MDC duty cycle must be maintained between 40% and 60% to support consistent sampling, and rise/fall times are required to be less than 20 ns for signal integrity. All Clause 22 frames are fully synchronized to the rising edges of MDC, with no support for burst modes, ensuring each management transaction is a discrete, clock-aligned operation. Setup and hold times for MDIO signals are critical to prevent data errors during transfers. When the station management entity (typically the MAC) drives the MDIO signal, it must ensure MDIO remains stable for at least 10 ns before and 10 ns after the rising edge of MDC. For PHY responses during read operations, the PHY must drive MDIO between 0 ns and 300 ns after the rising edge of MDC, providing flexibility for internal processing delays while bounding the overall transaction latency. The turnaround timing during read accesses facilitates bus handover from the MAC to the PHY without contention. After transmitting the register address, the MAC releases (tri-states) the MDIO line during the first turnaround bit, and the PHY begins driving the second turnaround bit (typically a logic 0) within 0 to 300 ns of the subsequent MDC rising edge. This mechanism ensures clean transitions on the bidirectional MDIO line. Error handling in Clause 22 relies on preamble detection for frame validity, with the PHY ignoring transactions lacking the required 32-bit all-ones preamble, prompting the MAC to retry the access. These timing constraints collectively support robust operation in noisy environments typical of Ethernet PHY management.

Frame Structure and Packet Format

The Clause 22 MDIO frame structure defines a fixed 64-bit format for management transactions over the serial bus, enabling reliable read and write access to PHY registers. The frame begins with a 32-bit preamble consisting of all logic 1s, which serves to synchronize the PHY's deserializer to the MDC clock, ensuring proper bit alignment before the control information is transmitted. This preamble is required prior to each management transaction. Following the preamble, a 14-bit control field specifies the transaction details: a 2-bit start delimiter (ST) fixed at 01 to demarcate the frame boundary, a 2-bit operation code (OP) indicating the access type (10 for read, 01 for write), a 5-bit PHY address (PHYAD) selecting the target device from 0 to 31, and a 5-bit register address (REGAD) identifying the specific register within the PHY from 0 to 31. The PHY address 00000 (0) functions as a broadcast address, allowing the transaction to reach all connected PHYs simultaneously, while individual addresses 00001 to 11111 (1-31) target specific devices. Standard register examples include address 0 for the basic mode control register (used for configuration such as speed selection and loopback) and address 1 for the basic mode status register (providing link status and capabilities). The control field is followed by a 2-bit turnaround (TA) field to manage bus contention and direction change, particularly for read operations, and concludes with a 16-bit data field holding the register value (MSB first). For write operations, the station management entity (STA, typically the MAC) drives the TA as 10 and immediately follows with the 16-bit data value to be written into the register. For read operations, the STA drives the first TA bit as 1 and tri-states the MDIO line (entering high-impedance, Z) for the second bit; the addressed PHY responds by driving a 0 on that second bit to acknowledge and avoid contention, then drives the 16-bit register value in the data field. After the data, the MDIO line returns to idle (tri-stated). This structure ensures orderly bus arbitration on the bidirectional MDIO line without additional signaling.
FieldBitsDescriptionExample Values
Preamble (PRE)32All 1s for synchronization1111... (32 times)
Start (ST)2Frame delimiter01
Operation (OP)2Access type10 (read), 01 (write)
PHY Address (PHYAD)5Target PHY (0 = broadcast)00000 to 11111
Register Address (REGAD)5Target register (e.g., 0 = control, 1 = status)00000 to 11111
Turnaround (TA)2Bus direction management10 (write, STA-driven); 1Z/0 (read, with PHY driving 0 on second bit)
Data16Register valueVariable (read from or written to register)

Access Commands and Operations

In Clause 22 of IEEE 802.3, access commands are defined through a set of opcodes that determine the type of register operation performed over the MDIO interface. These opcodes occupy the two bits immediately following the start field in the management frame and include: 00 for Address, which sets the register address for subsequent data operations without incrementing; 01 for Write, which writes 16 bits of data to the specified register; 10 for Read, which reads 16 bits from the specified register without incrementing the address; and 11 for Read Increment, which reads 16 bits from the current register address and then increments it for the next operation. Key registers accessed via these commands provide essential control and status functions for the PHY. Register 0, known as the Control register, includes bits for core operations such as bit 15 (Reset: writing 1 initiates a self-clearing reset of the PHY), bit 14 (Loopback: 1 enables internal loopback mode for testing), bits 13 and 6 (Speed Selection: combinations select operating speeds like 10 Mbps, 100 Mbps, or 1000 Mbps), and bit 12 (Auto-Negotiation Enable: 1 enables the auto-negotiation process). Register 1, the Status register, reports link conditions including bit 2 (Link Status: 1 indicates the link is up) and bit 5 (Auto-Negotiation Complete: 1 signals successful completion of auto-negotiation). Registers 4 and 5 support auto-negotiation: Register 4 (Auto-Negotiation Advertisement) allows the local PHY to advertise its capabilities such as supported speeds and duplex modes, while Register 5 (Auto-Negotiation Link Partner Base Page Ability) captures the abilities advertised by the link partner. The operational flow begins with the station (typically the MAC) transmitting a management frame by serially driving data onto the MDIO line, synchronized to the rising edges of the MDC clock signal. The targeted PHY latches the PHY address, opcode, and register address on successive rising edges of MDC; if the PHY address matches, it processes the command and, for reads, drives response data onto MDIO during the designated slots. In cases of invalid register addresses or unmatched PHY addresses, the PHY ignores the frame or returns all zeros on reads to indicate an error. Clause 22 imposes limitations on scalability and flexibility, supporting a maximum of 32 PHY devices (addressed via a 5-bit PHYAD field, 0 to 31) and 32 registers per PHY (via a 5-bit REGAD field, 0 to 31), with no provisions for addressing extensions or additional register space. Management frames are broadcast across the shared MDIO bus to all connected PHYs, but only the device with the matching PHYAD responds, enabling multi-device topologies while relying on address filtering. Common operational uses of these commands include enabling auto-negotiation by writing 1 to bit 12 of Register 0 via a Write opcode (01), which initiates capability exchange with the link partner. Additionally, link status polling involves repeated Read commands (opcode 10) to Register 1, checking bit 2 for a value of 1 to confirm an active link, often performed periodically by the station to monitor connectivity.

Clause 45 Enhancements

Key Differences from Clause 22

Clause 45 of the IEEE 802.3 standard was developed to address the limitations of Clause 22 in managing more complex physical layer (PHY) devices required for 10 Gigabit Ethernet and higher speeds, supporting multi-chip and multi-lane PHY configurations typical in backplane and high-speed applications. Unlike Clause 22, which was suited for simpler Gigabit Ethernet PHYs with limited register needs, Clause 45 enables access to a vastly expanded register space while maintaining backward compatibility through specific operational modes. In terms of frame structure, Clause 45 employs a two-phase approach consisting of a fixed 64-bit address frame followed by one or more fixed 64-bit data frames, which can be used for 16-bit transfers or multiple frames for 32-bit or 64-bit data, contrasting with Clause 22's fixed 64-bit frames that combine address and data in a single operation. This separation allows for more efficient handling of complex transactions, with Clause 45 frames using a start code of "00" to distinguish them from Clause 22's "01," and incorporating opcode fields with different interpretations for diverse operations. Addressing in Clause 45 utilizes a two-step process: first selecting the PHY device via a 5-bit port address (PRTAD), then targeting a specific MDIO Manageable Device (MMD) using a 5-bit device address (DEVAD, ranging from 0 to 31), followed by a 16-bit register address that supports up to 65,536 registers per MMD—far exceeding Clause 22's constraints of 32 PHYs and 32 registers each. This hierarchical scheme accommodates thousands of registers across multiple MMDs, such as PMA/PMD, PCS, and PHY XS, essential for managing intricate 10G+ PHYs. Additionally, Clause 45 supports MDC clock frequencies up to 4.25 MHz, enabling faster register access compared to Clause 22's 2.5 MHz limit. These modes ensure seamless integration in mixed environments while enabling advanced features like indirect addressing for Clause 22-style access to Clause 45 registers. Key advantages of Clause 45 include enhanced support for backplane applications and multi-lane PHYs through dedicated MMDs for lane-specific management. Additionally, it features a lower-voltage electrical interface (down to 1.2 V) compatible with modern CMOS processes, unlike Clause 22's higher-voltage requirements, facilitating integration in high-density systems.

Addressing Mechanisms and Device Access

Clause 45 of the IEEE 802.3 standard introduces the concept of MDIO Manageable Devices (MMDs), which are independent sublayers within a physical layer (PHY) entity that can be individually addressed and managed via the MDIO interface. Each PHY can contain up to 32 MMDs, identified by a 5-bit device address (DEVAD) ranging from 0 to 31, with specific assignments such as DEVAD 1 for PMA/PMD, 3 for PCS, 4 for PHY XS, 5 for DTE XS, and 7 for auto-negotiation. These MMDs support an extended register space of up to 65,536 registers each, addressed using a 16-bit register address (ADDR) from 0 to 65,535, enabling detailed control and status monitoring for complex high-speed Ethernet PHYs. The overall addressing hierarchy combines a 5-bit port address (PRTAD) for up to 32 PHYs on the MDIO bus, the DEVAD for the target MMD, and the 16-bit ADDR for the specific register within that MMD. Access to these registers occurs through a two-phase mechanism: an initial address frame sets the 16-bit ADDR for the specified PRTAD and DEVAD, followed by a data frame that performs the read or write operation on that address. Each frame is 64 bits long, beginning with a 32-bit preamble of all ones for synchronization, followed by a 2-bit start field (ST = 00 to indicate Clause 45 operation), a 2-bit operation code (OP), the 5-bit PRTAD, the 5-bit DEVAD, a 2-bit turnaround (TA) field, and a 16-bit data or address field transmitted MSB first. The OP codes specify the frame type: 00 for address (loading the ADDR), 01 for write (transferring 16 bits of data to the ADDR), 11 for read (retrieving 16 bits from the ADDR), and 10 for post-read-increment-address (reading data and then incrementing the ADDR by 1, up to a maximum of 65,535). The TA field manages bus direction: for reads and post-increment reads, the MDIO line is high-impedance for the first bit (allowing the MMD to drive 0 for the second), while for writes and address frames, the station management entity (STA) drives 10. To ensure backward compatibility with Clause 22, Clause 45 maps the original Clause 22 register set (addresses 0-31) to MMD 1 (DEVAD=1), where the 16-bit ADDR uses the Clause 22 register number in the lower 5 bits and zeros in the upper 11 bits. This allows Clause 45 interfaces to access legacy registers without modification, though voltage translation may be required for mixed Clause 22 and 45 devices. Access rules require the MDIO line to return to an idle state of high-impedance (pulled high by a system pull-up resistor) between frames, with a minimum inter-frame idle of at least one MDC clock cycle (400 ns at 2.5 MHz) to ensure proper bus settling and synchronization. MMDs must respond to all PRTAD and DEVAD combinations, returning zeros for undefined registers, and the post-read-increment operation supports sequential reads by automatically advancing the ADDR after each read completion.

Extended Commands and Register Management

Clause 45 of IEEE 802.3 introduces extended commands through a set of opcodes that enable two-phase access to registers, allowing for a larger address space compared to Clause 22. The opcodes are defined as follows: 00 for address frames, which set the target register address without data transfer; 01 for write data frames, which follow an address frame to write 16-bit data to the specified register; 11 for read data frames, which retrieve 16-bit data from the addressed register in response; and 10 for increment address operations, which advance the register address by one after a read or write for sequential access. Register organization in Clause 45 is structured around Management Data Input/Output Manageable Devices (MMDs), each with a dedicated 16-bit address space supporting up to 65,536 registers per MMD. MMD 1 provides compatibility with Clause 22 legacy registers, mapping traditional PHY control and status functions to its address space for backward interoperability, and handles Physical Medium Attachment/Physical Medium Dependent (PMA/PMD) functions, particularly for 10 Gb/s and higher rates, including transmitter and receiver parameters. MMD 7 is allocated for Auto-Negotiation, with vendor-specific extensions possible in higher address ranges, while vendor-specific MMDs (30 and 31) allow proprietary implementations. MMD 3 handles Physical Coding Sublayer (PCS) functions. Key registers within these MMDs support advanced Ethernet management. In MMD 7, auto-negotiation expansion registers (e.g., addresses 7.0.7 through 7.0.15) enable capability advertisement and selection for higher speeds like 40 Gb/s and 100 Gb/s, including base-R FEC options. Fault signaling is managed via status registers such as MMD 1.3.10 (receive fault) and MMD 1.3.11 (transmit fault), which latch errors for persistent indication until cleared. Power management features appear in control registers like MMD 1.0.11 (low-power mode enable), allowing energy-efficient states for idle links. Operations in Clause 45 accommodate high-speed PHYs by supporting 64-bit data through paired 32-bit register accesses or multiple frames, essential for configuring wide data paths in multi-lane systems. Error handling includes returning all zeros for invalid opcodes or unsupported registers, with status bits (e.g., MMD 1.1.2 for MDIO error latching) providing diagnostic feedback. These extended commands and registers are critical for 100 Gb/s Ethernet as defined in IEEE 802.3ba, where MMD 3 and 7 registers configure Forward Error Correction (FEC) modes and lane alignment status (e.g., via MMD 3.24.12). Similarly, in 400 Gb/s Ethernet per IEEE 802.3bs, Clause 45 manages FEC decoding, multi-lane synchronization, and power states across up to 16 lanes using expanded MMD address spaces.

References

  1. https://www.totalphase.com/support/articles/200349206-mdio-background/
  2. https://docs.nxp.com/bundle/AN14509/page/topics/mdio_interface.html
  3. https://community.cadence.com/cadence_blogs_8/b/fv/posts/importance-of-mdio-interface-for-ethernet
  4. https://www.ieee802.org/3/ak/public/jan03/WP2p0_cls45.pdf
  5. https://www.ti.com/lit/an/spracc8a/spracc8a.pdf
  6. https://www.st.com/resource/en/technical_note/tn1305-network-management-interfaces-stmicroelectronics.pdf
  7. https://standards.ieee.org/standard/802_3-2018.html
  8. https://standards.ieee.org/ieee/802.3/10422/
  9. https://www.ieee802.org/3/dm/public/0725/wienckowski_3dm_02_07292025.pdf
  10. https://ieeexplore.ieee.org/document/10472445
  11. https://www.prodigytechno.com/protocols/mdio-management-data-input-output
  12. http://magrawal.myweb.usf.edu/dcom/Ch3_802.3-2005_section2.pdf
  13. https://grouper.ieee.org/groups/802/3/10G_study/email/msg04549.html
  14. https://www.ti.com/lit/gpn/TLK100
  15. https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ApplicationNotes/ApplicationNotes/AN4754-Using-MCHP-Bridge-Controllers-with-External-Ethernet-PHYs-DS00004754.pdf
  16. https://www.ti.com/lit/gpn/DP83849C
  17. https://www.ieee802.org/3/NGAUTO/public/adhoc/perezaranda_NGAUTOah_190417.pdf
  18. https://community.nxp.com/t5/i-MX-Processors/MDIO-timing-on-i-MX6SX/td-p/631294
  19. https://www.intel.com/content/www/us/en/docs/programmable/683402/22-4-21-1-0/mdio-frame-format.html
  20. https://www.maxlinear.com/ds/618152_gpy111_pef7071vv16_hd_rev1.5.pdf
  21. https://docs.amd.com/r/en-US/pg138-axi-ethernet/Using-the-MII-Management-to-Access-Internal-or-External-PHY-Registers
  22. https://docs.amd.com/r/en-US/pg047-gig-eth-pcs-pma/Register-0-Control-Register
  23. https://guide.intrepidcs.com/docs/RAD-Gigastar/Advanced_Features.html
  24. https://www.ieee802.org/3/af/comments/d3.0/law_1_0102.pdf
  25. https://www.ieee802.org/3/efm/public/nov02/oam/pannell_oam_1_1102.pdf
  26. http://magrawal.myweb.usf.edu/dcom/Ch3_802.3-2005_section4.pdf
  27. https://www.intel.com/content/www/us/en/docs/programmable/683130/22-1/mdio-frame-format-clause-45.html
  28. https://www.ieee802.org/3/ca/public/meeting_archive/2018/11/remein_3ca_2a_1118.pdf
  29. https://www.ieee802.org/3/ap/public/comment_adhoc/P802.3ap_cls45_new_1005.pdf
  30. https://www.ieee802.org/3/ba/public/jul09/P8023ba-D21-Final_Responses_byClsa.pdf
  31. https://grouper.ieee.org/groups/802/3/bj/comments/P8023bj-D2p0-Comments_Final_byCls.pdf
  32. https://www.ieee802.org/3/bs/comments/P802d3bs_D3p0_comments_final_a_Cl.pdf
Add your contribution
Related Hubs
User Avatar
No comments yet.