Community hub
Recent from talks
Knowledge base stats:
Talk channels stats:
Members stats:
Ribbon cable
A ribbon cable is a cable with many conducting wires running parallel to each other on the same flat plane. As a result, the cable is wide and flat. Its name comes from its resemblance to a piece of ribbon.
Ribbon cables are usually seen for internal peripherals in computers, such as hard drives, CD drives and floppy drives. On some older computer systems (such as the BBC Micro and Apple II) they were used for external connections as well. The ribbon-like shape interferes with computer cooling by disrupting airflow within the case and also makes the cables awkward to handle, especially when there are a lot of them; as a result, round cables have almost entirely replaced ribbon cables for external connections and are increasingly being used internally as well.
The original form of ribbon cable was two-conductor 300 ohm twin lead cable used for radio and television, which is also called "ribbon cable". However the more modern forms more commonly called "ribbon cable" typically have many more than just two conductors.
Many-wire ribbon cable was invented in 1956 by Cicoil Corporation, a company based in Chatsworth, California. The company's engineers figured out how to use a new material, silicone rubber, to 'mold' a flat cable containing multiple conductors of the same size. Since the cable looked like a flat ribbon or duct tape, it was named a ribbon cable. The ribbon cable allowed companies like IBM and Sperry / Univac to replace bulky, stiff round cables with sleek, flexible ribbon cables.[citation needed]
The early ribbon cables were used in the mainframe computer industry, on card readers, card punching machines, and tape machines. Subsequently, ribbon cables were manufactured by a number of different companies, including 3M. Methods and materials were developed to simplify and reduce the cost of ribbon cables, by standardizing the design and spacing of the wires, and the thickness of the insulation, so that they could be easily terminated through the use of insulation-displacement connectors (IDC). The simplicity of the cables, their low profile (compared to contemporary alternatives), and low cost due to standardization, meant ribbon cables were long used in computers, printers, and many electronic devices.
To reduce the risk of reversed connections one edge of the cable is usually marked with a red stripe. By convention the edge with the stripe is connected to pin 1 on the connector. This method of identification is fine for cables that just consist of two or more IDC connectors with every connector connecting to every wire, but is somewhat less helpful when individual wires or small groups of wires must be terminated separately.
To make it easier to identify individual conductors in a cable; ribbon-cable manufacturers introduced rainbow ribbon cable, which uses a repeating pattern of colors borrowed from the standard resistor color code (Brown is pin 1 or pin 11 or pin 21, etc. Red is pin 2 or pin 12 or pin 22, etc.). It is sometimes known affectionately to its users as hippie cable due to its distinct appearance.
Ribbon cables are usually specified by two numbers: the spacing or pitch of the conductors, and the number of conductors or ways. A spacing of 0.05 inch (1.27 mm) is the most usual, allowing for a two-row connector with a pin spacing of 0.1 inch (2.54 mm). These types are used for many types of equipment, in particular for interconnections within an enclosure. For personal computers, this size was used in floppy-disk-drive cables and older or custom Parallel ATA cables.
Hub AI
Ribbon cable AI simulator
(@Ribbon cable_simulator)
Ribbon cable
A ribbon cable is a cable with many conducting wires running parallel to each other on the same flat plane. As a result, the cable is wide and flat. Its name comes from its resemblance to a piece of ribbon.
Ribbon cables are usually seen for internal peripherals in computers, such as hard drives, CD drives and floppy drives. On some older computer systems (such as the BBC Micro and Apple II) they were used for external connections as well. The ribbon-like shape interferes with computer cooling by disrupting airflow within the case and also makes the cables awkward to handle, especially when there are a lot of them; as a result, round cables have almost entirely replaced ribbon cables for external connections and are increasingly being used internally as well.
The original form of ribbon cable was two-conductor 300 ohm twin lead cable used for radio and television, which is also called "ribbon cable". However the more modern forms more commonly called "ribbon cable" typically have many more than just two conductors.
Many-wire ribbon cable was invented in 1956 by Cicoil Corporation, a company based in Chatsworth, California. The company's engineers figured out how to use a new material, silicone rubber, to 'mold' a flat cable containing multiple conductors of the same size. Since the cable looked like a flat ribbon or duct tape, it was named a ribbon cable. The ribbon cable allowed companies like IBM and Sperry / Univac to replace bulky, stiff round cables with sleek, flexible ribbon cables.[citation needed]
The early ribbon cables were used in the mainframe computer industry, on card readers, card punching machines, and tape machines. Subsequently, ribbon cables were manufactured by a number of different companies, including 3M. Methods and materials were developed to simplify and reduce the cost of ribbon cables, by standardizing the design and spacing of the wires, and the thickness of the insulation, so that they could be easily terminated through the use of insulation-displacement connectors (IDC). The simplicity of the cables, their low profile (compared to contemporary alternatives), and low cost due to standardization, meant ribbon cables were long used in computers, printers, and many electronic devices.
To reduce the risk of reversed connections one edge of the cable is usually marked with a red stripe. By convention the edge with the stripe is connected to pin 1 on the connector. This method of identification is fine for cables that just consist of two or more IDC connectors with every connector connecting to every wire, but is somewhat less helpful when individual wires or small groups of wires must be terminated separately.
To make it easier to identify individual conductors in a cable; ribbon-cable manufacturers introduced rainbow ribbon cable, which uses a repeating pattern of colors borrowed from the standard resistor color code (Brown is pin 1 or pin 11 or pin 21, etc. Red is pin 2 or pin 12 or pin 22, etc.). It is sometimes known affectionately to its users as hippie cable due to its distinct appearance.
Ribbon cables are usually specified by two numbers: the spacing or pitch of the conductors, and the number of conductors or ways. A spacing of 0.05 inch (1.27 mm) is the most usual, allowing for a two-row connector with a pin spacing of 0.1 inch (2.54 mm). These types are used for many types of equipment, in particular for interconnections within an enclosure. For personal computers, this size was used in floppy-disk-drive cables and older or custom Parallel ATA cables.