Soil liquefaction occurs when a cohesionless saturated or partially saturated soil substantially loses strength and stiffness in response to an applied stress such as shaking during an earthquake or other sudden change in stress condition, in which material that is ordinarily a solid behaves like a liquid. In soil mechanics, the term "liquefied" was first used by Allen Hazen in reference to the 1918 failure of the Calaveras Dam in California. He described the mechanism of flow liquefaction of the embankment dam as:

If the pressure of the water in the pores is great enough to carry all the load, it will have the effect of holding the particles apart and of producing a condition that is practically equivalent to that of quicksand... the initial movement of some part of the material might result in accumulating pressure, first on one point, and then on another, successively, as the early points of concentration were liquefied.

The phenomenon is most often observed in saturated, loose (low density or uncompacted), sandy soils. This is because a loose sand has a tendency to compress when a load is applied. Dense sands, by contrast, tend to expand in volume or 'dilate'. If the soil is saturated by water, a condition that often exists when the soil is below the water table or sea level, then water fills the gaps between soil grains ('pore spaces'). In response to soil compressing, the pore water pressure increases and the water attempts to flow out from the soil to zones of low pressure (usually upward towards the ground surface). However, if the loading is rapidly applied and large enough, or is repeated many times (e.g., earthquake shaking, storm wave loading) such that the water does not flow out before the next cycle of load is applied, the water pressures may build to the extent that it exceeds the force (contact stresses) between the grains of soil that keep them in contact. These contacts between grains are the means by which the weight from buildings and overlying soil layers is transferred from the ground surface to layers of soil or rock at greater depths. This loss of soil structure causes it to lose its strength (the ability to transfer shear stress), and it may be observed to flow like a liquid (hence 'liquefaction').

Although the effects of soil liquefaction have been long understood, engineers took more notice after the 1964 Alaska earthquake and 1964 Niigata earthquake. It was a major cause of the destruction produced in San Francisco's Marina District during the 1989 Loma Prieta earthquake, and in the Port of Kobe during the 1995 Great Hanshin earthquake. More recently soil liquefaction was largely responsible for extensive damage to residential properties in the eastern suburbs and satellite townships of Christchurch during the 2010 Canterbury earthquake and more extensively again following the Christchurch earthquakes that followed in early and mid-2011. On 28 September 2018, an earthquake of 7.5 magnitude hit the Central Sulawesi province of Indonesia. Resulting soil liquefaction buried the suburb of Balaroa and Petobo village 3 metres (9.8 ft) deep in mud. The government of Indonesia is considering designating the two neighborhoods of Balaroa and Petobo, that have been totally buried under mud, as mass graves.^{[needs update]}

The building codes in many countries require engineers to consider the effects of soil liquefaction in the design of new buildings and infrastructure such as bridges, embankment dams and retaining structures.

Soil liquefaction occurs when the effective stress (shear strength) of soil is reduced to essentially zero. This may be initiated by either monotonic loading (i.e., a single, sudden occurrence of a change in stress – examples include an increase in load on an embankment or sudden loss of toe support) or cyclic loading (i.e., repeated changes in stress condition – examples include wave loading or earthquake shaking). In both cases a soil in a saturated loose state, and one which may generate significant pore water pressure on a change in load are the most likely to liquefy. This is because loose soil has the tendency to compress when sheared, generating large excess porewater pressure as load is transferred from the soil skeleton to adjacent pore water during undrained loading. As pore water pressure rises, a progressive loss of strength of the soil occurs as effective stress is reduced. Liquefaction is more likely to occur in sandy or non-plastic silty soils but may in rare cases occur in gravels and clays (see quick clay).

A 'flow failure' may start if the current strength of the soil falls below the strength required to maintain the equilibrium of a slope or footing of a structure. This can occur due to monotonic (single-event) loading or cyclic loading, and can be sudden and catastrophic. A historical example is the Aberfan disaster. Casagrande referred to this type of phenomena as 'flow liquefaction', although a state of zero effective stress is not required for this to occur.

'Cyclic liquefaction' is the state of soil when large shear strains have accumulated in response to cyclic loading. A typical reference strain for the approximate occurrence of zero effective stress is 5% double amplitude shear strain. This is a soil test-based definition, usually performed via cyclic triaxial, cyclic direct simple shear, or cyclic torsional shear type apparatus. These tests are performed to determine a soil's resistance to liquefaction by observing the number of cycles of loading at a particular shear stress amplitude required to induce 'fails'. Failure here is defined by the aforementioned shear strain criteria.