The General Electric Passport is a turbofan developed by GE Aerospace for large business jets. It was selected in 2010 to power the Bombardier Global 7500 and 8000, first run on June 24, 2013, and first flown in 2015. It was certified in April 2016 and powered the Global 7500 first flight on November 4, 2016, before its 2018 introduction. It produces 14,000 to 20,000 lbf (60 to 90 kN) of thrust, a range previously covered by the General Electric CF34-10. A smaller scaled CFM LEAP, it is a twin-spool axial engine with a 5.6:1 bypass ratio, a 45:1 overall pressure ratio and one-piece 52 in (130 cm) titanium fan blisk with 18 blades.

The GE eCore research program, which developed a common architecture for business, narrowbody and regional jets, resulted in the CFM LEAP engine which replaced the CFM56 on the Boeing 737 MAX and Airbus A320neo. After a market study, GE pursued the long-range, large business jet requirement and selected a 14,000–20,000 lbf (62–89 kN) thrust range using technology it had developed for its commercial and military engine programs. Preliminary design work started in 2009. In 2010, Bombardier Aerospace selected the engine with a 16,500 lbf (73 kN) rating for the Global 7000 announced at the same year NBAA convention. Testing of the engine core began in 2010. On May 16, 2011, the TechX was renamed the Passport.

In 2011, rig testing started for components such as the combustor and high-pressure turbine. In 2012, a fan blade-off test was done to confirm whether the fan case could stop blade parts from passing through the case and causing further damage. By 2013, testing of engines had started at the GE outdoor testing site at Peebles, Ohio. In 2014 bird ingestion and endurance tests were done. In 2015, the Passport first flew installed on the GE Boeing 747-100 flying testbed based at Victorville, California. Icing and water ingestion tests up to simulated altitudes of 51,000 feet were done at the U.S. facility in Tennessee.

In April 2016, it was FAA Certified after 3,380 hours and 3,385 cycles of testing. The Global 7000 made its maiden flight with it on November 4, 2016. It flew 100 hours on the Boeing 747 before logging more than 900 hours aboard the Global 7000 prototypes. By May 2017, the engines had completed 3,100h in ground and flight test.

On 15 August 2017, the Global 7000 second prototype's right engine suffered an in-flight flameout at FL410, after “high vibration and high inter-turbine temperature readings”; subsequently, the airplane returned to Wichita Airport (290 km away) for a single engine landing. It was traced to a mis-assembled part and a fleet-wide inspection revealed it was a one-off error.

In autumn 2017, GE was building the flight test engines for Bombardier while preparing for early manufacturing. By service entry in 2018, 4,000 hours and 8,000 cycles of testing should be completed.

In 2021, General Electric tendered Passport to the USAF to be assessed in a contest against Rolls-Royce and Pratt & Whitney to reengine the B-52H Stratofortress. The contract was awarded to Rolls-Royce.

The engine is a twin-spool, axial-flow turbofan with a high bypass ratio of 5.6:1 and an overall pressure ratio of 45:1. The front fan is attached to the three-stage low-pressure compressor; the 23:1 pressure ratio 10-stage high-pressure compressor includes five blisk stages for weight reduction. The low-emission combustor has a case with integrated OGV diffuser for weight reduction. There is a two-stage high-pressure and four-stage low-pressure turbine. The engine and aircraft accessory drive extracts energy from the high-pressure, high-speed rotor. It is equipped with a dual-channel Full Authority Digital Engine Control (FADEC) control system, providing fault isolation and engine functionality and diagnostics capability.