Hubbry Logo
No. 68 AT grenadeNo. 68 AT grenadeMain
Open search
No. 68 AT grenade
Community hub
No. 68 AT grenade
logo
7 pages, 0 posts
0 subscribers
Be the first to start a discussion here.
Be the first to start a discussion here.
No. 68 AT grenade
No. 68 AT grenade
No. 68 AT grenade
View on Wikipedia
from Wikipedia

The Grenade, Rifle No. 68 / Anti-Tank was a British anti-tank rifle grenade used during the Second World War and was one of the first operational weapons to utilise the shaped charge principle.

Key Information

Design

[edit]
A member of the Home Guard demonstrates a Lee-Enfield rifle equipped to fire an anti-tank grenade, Dorking, 3 August 1942.

British research into shaped charges in the inter-war period brought about some useful progress but did not result in any weapons. Development of the grenade started in late 1939, after a demonstration arranged for a British military commission of a series of anti-tank rifle grenades and artillery warheads at the Swiss Army Proving Ground at Thun in Switzerland, which had been designed by Henry Mohaupt. Guessing that Mohaupt's weapons were using the hollow charge principle, the British abandoned negotiations and began development of a rifle grenade based on their own previous work.[1]

The No. 68 has some claim to have been the first high-explosive anti-tank (HEAT) device in use. The design of the warhead was simple and was capable of penetrating 52 mm (2.0 in) of armour.[2]

The fuze of the grenade was armed by removing a pin in the tail which prevented the firing pin from flying forward. The grenade was launched from a rifle cup. The simple fins gave it some stability in the air and, provided the grenade hit the target at the proper angle (90 degrees), the charge would be effective. Detonation occurred on impact, when a striker in the tail of the grenade overcame the resistance of a creep spring and was thrown forward into a stab detonator.[3]

The grenade was fired, as was the No. 36M Mills bomb, from a specially adapted Lee-Enfield Rifle No. 1 EY,[a] often converted from a rifle that was unfit for general use and had been marked "DP" for drill purpose. The converted rifles were strengthened by adding an extra bolt to secure the breech mechanism to the stock, and by a cord binding which was fastened around the forestock. A special Ballistite high-explosive cartridge was required to propel the grenade. The grenade itself was held in place by the 2+1⁄2 inches (64 mm) discharger cup No. 1 Mk I. With the weapon's introduction into Home Guard use, the Adaptor No. 1 and the Discharger No. 2 Mk I were introduced, which allowed grenades to be launched from the M1917 Enfield rifle with which they were equipped, although a contemporary manual warned that rifles used for that purpose were likely to be "somewhat spoilt as a precision weapon".[5]

Service

[edit]

The No. 68 grenade entered service with the British Army in November 1940.[1] However, it proved to be not much better than the inadequate Boys anti-tank rifle and could not be improved as the size of the explosive charge was limited by the diameter of the discharger cup,[6] It was introduced into service with the Home Guard in February 1941 and was retained until the force stood-down in 1944.[7]

A British manual of 1942, reflecting experience gained in the field, stated that the effective range of the grenade was 50 to 70 yards (45 to 65 metres) and would be best employed against the rear armour of enemy tanks after they had been allowed to pass.[8]

Notes

[edit]

References

[edit]
[edit]
Revisions and contributorsEdit on WikipediaRead on Wikipedia

No. 68 AT grenade

View on Grokipedia
from Grokipedia
The No. 68 AT grenade, officially designated the Grenade, Rifle No. 68 / Anti-Tank, was a British () introduced during as one of the earliest operational shaped-charge munitions in . It featured a hollow-charge that, upon impact, generated a focused jet of molten metal to penetrate armored fighting vehicles, with capabilities of up to 50 mm of armor at a 0° and 40 mm at 30°. Weighing approximately 0.89 kg and measuring 168 mm in length with a 63.2 mm diameter, it was fin-stabilized in early variants and launched from a .303-inch via a cup discharger attachment or the Northover Projector used by units, achieving an effective range of 50–75 yards. Developed in response to the threat of early German Panzer tanks, the No. 68 represented the first practical application of the hollow-charge principle in British munitions, entering service in November 1940 with initial production of 10,000 units. It evolved through five marks: the Mark I with stabilizing fins and a ; Mark II featuring a mazak body without fins; Mark III incorporating a larger explosive pellet and improved liner; Mark IV with a mazak ; and Mark V using a steel , with some production occurring in the United States. The warhead was filled with 5.5 ounces of high explosive, such as Lyddite, Pentolite, /BWX, PE, or CE/TNT, and employed an impact with a graze action mechanism involving a shear wire and for arming after launch. Primarily issued to British and forces for infantry anti-tank roles, the grenade saw frontline use until around 1942, after which it was largely relegated to training and reserve stocks as German tank armor thickened beyond its penetration limits and more advanced weapons like the emerged. Production scaled massively, reaching 2.6 million units in 1941 and 5.3 million in 1942, ensuring widespread availability until manufacturing ceased in 1945. Despite its limitations against later armored threats, the No. 68's innovative design influenced subsequent weaponry and marked a pivotal step in anti-tank .

Development and Production

Origins and Development

Prior to the outbreak of World War II, British military authorities grew increasingly concerned about the vulnerability of infantry to rapidly advancing armored vehicles, as tank armor thicknesses had exceeded the capabilities of standard small arms and early anti-tank rifles like the Boys, prompting the search for a lightweight, rifle-launched projectile capable of penetrating armored targets from a safe distance. Development of the No. 68 AT grenade began in 1940 at the Woolwich Arsenal under the British . This effort was directly influenced by demonstrations of technology conducted by Swiss engineer Henry Mohaupt, whose 1939 and demonstrations of technology in 1940 influenced British researchers to pursue similar effects in fin-stabilized rifle grenades rather than pursuing licensing agreements. Key contributions came from Woolwich researchers including Evans, Ubbelohde, Taylor, Tuck, Mott, and others. The grenade was officially introduced in November 1940 as the Grenade, Rifle No. 68 / Anti-Tank, representing the first operational military use of a hollow charge warhead in a fin-stabilized design, launched from a cup discharger attached to the Lee-Enfield rifle. Early testing phases, conducted at British military proving grounds following Mohaupt's demonstrations, validated the design's effectiveness, with trials demonstrating penetration of up to 50 mm (2 inches) of armor plate at a 90-degree impact , though performance dropped to around 40 mm at 30-degree , establishing key milestones for its approval and initial production.

Manufacturing and Variants

Production of the No. 68 AT grenade began ramping up in late 1940 following its approval, with handled by various British firms to meet wartime demands. By , millions of units had been produced, enabling widespread issuance to frontline troops before transitioning to reserves. The grenade utilized standard materials suited for , including an (Mazak) bell-shaped body for the and a tail unit with four stabilizing vanes, often constructed from or lightweight metal s in later marks. The hollow charge was filled with approximately 5.5 ounces (156 grams) of high explosive, typically Composition A (/wax 91/9), though early variants used Lyddite, Pentolite, or other mixtures like C.E./TNT. Several minor variants emerged through Marks I to VI, focusing on enhancements to the assembly, cavity liner, and tail construction for improved reliability without altering the core design. For instance, the Mk I featured small tail vanes and a hemispherical liner, while the Mk IV integrated the tail and gas check from Mazak, and the Mk VI—produced in the United States—used a tail tube with spot-welded fins. No major redesigns occurred during the war, preserving production efficiency. To support training, an inert drill version known as the No. 68 Drill was introduced, externally identical to the live but lacking any explosive filler and using safe substitutes like rubber components. Manufactured in by firms such as A. & F. Pears Limited and the Peterborough Die Casting Company, it allowed realistic practice with the rifle discharger. The grenades were distributed across forces, including significant quantities to Canadian units for anti-tank training and operations.

Design and Functionality

Components and Construction

The No. 68 AT grenade features a bell-shaped body constructed from or die-cast Mazak (a ), measuring 6.6 inches (168 mm) in length and 2.5 inches (63.2 mm) in diameter, with a total filled weight of 1 lb 15.5 oz (0.89 kg). The body is externally threaded for a and internally threaded for the assembly, allowing secure integration of components during . The core of the grenade is its hollow charge warhead, comprising the bell-shaped body filled with 5.5 oz (156 g) of explosive such as Lyddite, Pentolite, C.E./TNT (30/70 mix), or RDX/BWX (91/9 mix), topped with a small amount of TNT for stability. At the open nose end, a thin metal cavity liner—hemispherical in early marks like Mk I, or cylindro-conoidal in later marks like Mk III—forms the shaped charge cone to direct the explosive force. A body cap secures the liner and a thin metal disc (brass, tinned plate, or steel) over the nose. The tail unit, made of die-cast Mazak, includes four straight metal stabilizing vanes for flight stability and a central recess housing the impact mechanism. The consists of a rust-proofed striker or needle, held in place by a passing through the tail and a shear wire, with a detonator holder containing a 5-grain A.Z. and a C.E. pellet. A plate, of in Mk V or integral Mazak casting in Mk IV, attaches to the tail base via rivets, crimping, or screws to interface with the rifle's gases. For launch, the grenade's tail rod-like extension fits into the No. 1 Mk I cup discharger mounted on the muzzle of a Lee-Enfield rifle (such as the No. 4 Mk I), propelled by the pressure from a .303-inch blank cartridge containing 30 grains of ballistite. Safety is ensured by the pin, which blocks striker movement until intentionally withdrawn, and the shear wire, which resists premature release but breaks on sufficient impact. The overall assembly prioritizes robust, threaded connections and cast components for reliable field use.

Operational Mechanism and Performance

The No. 68 AT grenade is launched by attaching it to a cup discharger fitted on the muzzle of a .303-inch Lee-Enfield rifle, with the safety pin removed prior to firing; propulsion is provided by a .303-inch blank cartridge, which expels the grenade in an arcing trajectory requiring the firer to elevate the rifle for distance adjustments. The effective range is typically 50 to 75 yards (46 to 69 meters), though some accounts extend this to 100 yards (91 meters) under optimal conditions, limited by the grenade's low velocity and the need for precise aiming to achieve perpendicular impact on armored targets. In flight, the grenade is stabilized by four straight tail vanes that prevent tumbling, ensuring a relatively straight path despite the ballistic arc; the tail assembly includes a gas check to seal against the discharger during launch. Upon impact, a mechanical fuze activates via setback and graze action: initial launch force shears a copper wire to arm the striker, which is then held by a creep spring until impact drives it into the detonator, igniting the main charge without delay. This initiates the shaped charge warhead, utilizing the Munroe effect to collapse a metal liner into a high-velocity jet that penetrates armor. Performance against targets centers on the directional nature of the , which produces a minimal lethal radius for anti-personnel effects but excels in armor penetration: it can defeat up to 50 mm (2 inches) of homogeneous armor plate at a 90-degree of impact, reducing to approximately 40 mm at 30 degrees due to the jet's sensitivity to obliquity. The warhead's 5.5 ounces (156 grams) of explosive filling, typically /wax, Pentolite, or Lyddite, focuses energy forward, limiting fragmentation and to mere inches beyond the jet path. Ballistic constraints, including the arcing flight path and requirement for near-perpendicular strikes, further restrict effectiveness against moving or obliquely angled vehicles.

Operational History

Introduction and World War II Use

The Grenade, Rifle No. 68 / Anti-Tank was officially introduced to infantry units in November 1940 as an urgent response to the growing threat posed by German Panzer divisions in and . Developed as the first operational shaped-charge weapon in British service, it equipped riflemen with a portable means to engage armored vehicles at short ranges, filling a critical gap left by the obsolescing . This introduction occurred amid the early pressures of the war, enabling infantry sections to carry a squad-level anti-tank capability without relying on heavier artillery support. Training protocols emphasized safe and accurate handling, with No. 68 drill grenades issued for practice to simulate live firings without risk. Soldiers were instructed to use the rifle's cup discharger, aiming primarily at vulnerable points such as tracks or from the rear or sides where armor was thinnest, at effective ranges of 50 to 75 yards. Lessons from official pamphlets stressed loading behind cover, using cartridges for propulsion, and practicing rapid fire with assistant loaders to simulate combat conditions. Improvised wooden drill grenades were permitted when standard ones were unavailable, ensuring widespread familiarity among troops. The grenade saw frontline combat with British and forces until around 1942, primarily in anti-tank roles against early-war German armor. Specific instances of its use in major battles are not well-documented. It was issued to British and forces, with production scaling to millions of units by war's end to support frontline distribution.

Post-War Service and Withdrawal

Following the end of , the No. 68 AT grenade saw no documented active service in British or forces. The grenade, which had been shifted from frontline use to Home Guard units in 1942 for defense against potential invasion, was fully withdrawn from service in 1945. Production ceased the same year, with approximately 8 million units manufactured in the and additional quantities produced in the United States for supply to Britain and . Remaining stockpiles from wartime production were decommissioned , with many converted to inert versions for purposes, as surviving examples indicate.

Legacy and Impact

Limitations and Drawbacks

The No. 68 AT 's fuze system, a simple graze-action mechanism relying on a shear wire and striker, required removing a tail prior to firing, which exposed the grenade to potential premature from rough handling, vibration, or environmental factors like wind gusts en route to the target. This design necessitated careful user handling. Its limited effective range, typically 50 to 75 yards when fired from an "EY" rifle, further hampered tactical utility, as the low-velocity launch made the grenade susceptible to wind drift and ballistic drop-off beyond this distance. Accuracy was notably poor at the upper end of this range due to the flat trajectory and the need for a prone firing position, often reducing practical engagement distances to as little as 50 yards in later assessments to ensure hits on moving armored targets. These constraints forced infantry to close dangerously near enemy vehicles, exposing users to small-arms fire and machine-gun suppression. Vulnerability to user error was a significant drawback, as the shaped charge warhead demanded near-perpendicular impact (ideally 0 degrees) for optimal penetration of up to 50 mm of armor plate, dropping to 40 mm at a 30-degree angle of obliquity. Oblique strikes or impacts on spaced armor reduced effectiveness dramatically, rendering the grenade largely useless against heavier tanks like the German , whose side armor exceeded 3 inches (80 mm) in many areas. This precision requirement, combined with the grenade's rudimentary design, limited its battlefield impact against evolving armored threats. Safety hazards arose during transport, storage, and arming, where the exposed after pin removal posed risks of accidental initiation if the grenade was jostled or dropped, particularly in scenarios involving repeated handling and rifle mounting. This underscored the need for stringent safety protocols that complicated logistics for and regular units alike. Compared to subsequent anti-tank weapons, the No. 68 demonstrated clear inferiority, offering far less standoff range than the (effective direct fire up to 115 yards) or the American (up to 275 yards), which also provided greater penetration and ease of use without requiring rifle integration. These later systems addressed the grenade's core flaws in mobility, accuracy, and reliability, leading to its phased withdrawal in favor of more versatile launchers.

Influence on Subsequent Weapons

The No. 68 AT grenade holds pioneering status as the world's first operational high-explosive anti-tank (HEAT) rifle grenade, introduced into British service in November 1940, which directly influenced the development of similar Allied weapons during World War II. Its shaped charge warhead, utilizing the Munroe effect to focus explosive energy into a penetrating jet, demonstrated the feasibility of man-portable anti-tank capabilities against increasingly armored vehicles, prompting the United States to adapt similar technology for the M9 bazooka warhead in 1942, where British expertise in hollow-charge design was shared through Lend-Lease collaboration. This early success validated rifle-launched HEAT munitions as a viable interim solution until more advanced systems emerged. The grenade's technological legacy extended into post-war designs, where its core principle was refined and adopted in subsequent British and international anti-tank s. It was superseded by the improved No. 85 in 1943, which enhanced penetration efficiency to about 1.5 charge diameters, building directly on the No. 68's foundational liner and explosive configuration. Further evolutions included the No. 94 (Energa) introduced in the early 1950s, which incorporated stabilized flight and greater standoff distance while retaining the HEAT mechanism pioneered by the No. 68, and influenced broader adoption in (RPG) systems like the Soviet RPG-2. These advancements traced back to wartime lessons from the No. 68, emphasizing conical liners for jet formation. Doctrinally, the No. 68 shifted anti-tank tactics toward lightweight, rifle-fired munitions that enabled squad-level engagement of armored targets at ranges up to 100 yards, reducing reliance on cumbersome and informing the design of Cold War-era portable systems like the spigot mortar, which evolved from the grenade's limitations to provide 115mm penetration. This emphasis on man-portable launchers laid groundwork for guided missile technologies, prioritizing mobility in anti-armor roles. In , the No. 68 is recognized as a key innovation in application despite its operational constraints, with examples preserved in institutions such as the , where drill and live variants illustrate its role in early development. Its indirect influence persists in modern fin-stabilized munitions, such as those used in the Carl Gustaf , which adopted WWII-era warheads scaled for 84mm caliber to achieve multi-layer armor defeat.
Add your contribution
Related Hubs
User Avatar
No comments yet.