Hubbry Logo
Group Rally5Group Rally5Main
Open search
Group Rally5
Community hub
Group Rally5
logo
8 pages, 0 posts
0 subscribers
Be the first to start a discussion here.
Be the first to start a discussion here.
Group Rally5
Group Rally5
from Wikipedia
Group Rally5
Motor racing formula
CategoryRallying
Country/RegionInternational
ChampionshipsWRC, Regional, National
Inaugural2019 (2008 as R1)
StatusActive
DrivetrainTwo Wheel Drive
Power to weight6.4kg/hp
AptitudeAccess

Group Rally5 is a technical specification of rally car determined by the FIA for use in its international rallying competitions: World Rally Championship (WRC) and regional championships. National rallying competitions also allow Group Rally5 cars to compete. There are no subclasses of the group therefore all Group Rally5 cars can compete in the same category. 'Rally5' may be used alone with the same definition. The group was launched in 2019 after the introduction of the Rally Pyramid initiative to reorganise the classes of car and championships in international rallying was approved in June 2018.[1]

The formula for Group Rally5 cars was taken from R1 class of Group R with the defining ruleset interchanging the terms, this meant that any existing R1 car homologated or approved since their introduction in 2008 could continue to be used in Rally5 level competition.[2] The subclasses defined in R1 however have effectively merged and capacity of permitted turbocharged engines have increased to 1333cc.[2]

In July 2024, the FIA announced slightly modified Group Rally5 cars will be eligible to race in circuit touring car racing under the name of TC Lite 5 (TCL5) from 2025.[3][4]

Definition

[edit]

Group Rally5 cars are defined in FIA document Appendix J - Article 260 as Touring Cars or Large Scale Series Production Cars, supercharged Petrol engine (including rotary engines), 2-wheel drive (front or rear wheel drive). A production touring car with at least 2500 identical units manufactured must be homologated in Group A, with all the requirements that make it a Group Rally5 car homologated in an extension.[2] They have a power to weight ratio of 6.4kg/hp.[1]

Rally5 rules are relaxed in comparison to the other Groups Rally formulae making it the most cost efficient and accessible. Only the bodyshell (with safety cage), the seat mountings and the harness need to be homologated, the latter two already having their own Appendix J ruleset outside of Rally5. Bodyshells homologated under Group Rally4 regulations are also permitted in Group Rally5 therefore potentially expanding the range of cars available. Most components of the original Group A model can be used and in many cases are free to replace, however in such cases the performance criteria of Rally5 must always be met.

Key Specific Regulations for Cars in Group Rally5[2]
Drivetrain Minimum

Weight

Engine

Capacity

Aspiration Fuel Maximum

Cylinders

Turbo

Restrictor

Wheels

Gravel

Wheels

Asphalt

Production

Requirement

2WD 1030 kg Up to 1600cc Normal Petrol 6 As manufactured 6"x15" 6.5"x16" 2500
Up to 1067cc Turbo
1080 kg 1067-1333cc

FIA Competition

[edit]

Rally5 cars are placed in FIA 'RC5' sporting class alone.

Eligibility in FIA WRC Championships 2023
Class Group WRC M T WRC2 WRC3 Masters Junior
RC5 Rally5 Yes Yes
Eligibility in FIA Regional Championships 2023
Class Group ALL ERC ERT ARC MERC APRC NACAM CODASUR
Absolute Teams ERC3 ERC4 Jun Jun ARC2 ARC3 ARC4 Jun MERC2 MERC3 MERC4 Jun APRC3 APRC4 Jun NAC3 NAC4 Jun COD2 COD3 COD4
RC5 Rally5 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes

Cars

[edit]
Manufacturer Car Debut Homologation Basis Image
France Citroën DS3 R1 2012 FIA - A5739
DS3 VTI 120 So Chic
1598cc Normal
Monte-Carlo WRC 2014 ES2 - 12048975956
United Kingdom Ford Fiesta Rally5[5] 2020 FIA - A5775
Fiesta ST-Line (Fiesta Mk7)
999cc Turbo
United Kingdom Ford Fiesta R1 2012 FIA - A5729
Fiesta 1.6 (Fiesta Mk6)
1597cc Normal
2021 Rally Bohemia - Kalina
France Renault Clio Rally5[6] 2020 FIA - A5779
Clio R.S. Line TCE 1.3EDC
1331cc Turbo
France Renault Twingo R1 2010 FIA - A5731
Twingo "Renault Sport"
1598cc Normal
2013 Rallye Sunseeker (10367080843)
Japan Toyota Vitz 2012 FIA - A5742
Vitz (NCP131)
1501cc Normal
Japan Mazda 2 R1 2020 FIA - no homologation
Approved for use in FIA NACAM
Built by GHR Motorsport[7][8][9][10]
Japan Suzuki Swift Rally5 - FIA - no homologation

Project of Suzuki Motorsport[11]

Source: FIA Homologation List 2021[12]

In addition to the above, bodyshells (and safety cage) homologated in Group Rally4 since 2020 would also be accepted subject to meeting Rally5 criteria elsewhere. For example, where original parts must be used, or power and weight limits met:

See also

[edit]

References

[edit]
[edit]
Revisions and contributorsEdit on WikipediaRead on Wikipedia
from Grokipedia
Group Rally5 is a technical classification of rally cars established by the (FIA) for participation in international rally events, serving as the foundational level of the FIA Rally Pyramid to facilitate accessible entry into competitive . These vehicles are derived from touring cars or large-scale series production models featuring petrol engines—including rotary engines—and configurations, either front- or , with a minimum of four seats as per standards. Introduced as part of the FIA's efforts to structure a clear progression pathway from novice to elite levels in , Group Rally5 emphasizes affordability, , and performance balance for beginners while adhering to strict production-based modifications. Cars in this group are divided into subclasses based on engine specifications: normally aspirated engines up to 1,600 cm³ or supercharged engines up to 1,333 cm³, with the original supercharging system required to be retained and no additional devices permitted. Minimum weights range from 1,030 kg for normally aspirated or smaller supercharged variants to 1,080 kg for larger supercharged engines, ensuring competitive equity on and tarmac surfaces. Safety is paramount, with mandatory features including a homologated cage welded to the bodyshell, FIA-approved five-point harnesses, and reinforced anchorages, all detailed in the vehicle's Rally5 form (VRa5). modifications are limited to preserve series-production integrity, such as free-form suspension spring and bolted reinforcement bars within specified tolerances, while ground clearance must meet or exceed the homologated value. Eligible models, homologated via national sporting authorities or directly by the FIA, include popular front-wheel-drive superminis like the Rally5, which exemplify the category's role in nurturing talent through national and regional championships before advancing to higher groups like Rally4 or Rally3. In addition to standard Rally5 cars, the FIA introduced the Rally5-Kit subcategory in 2024 to broaden accessibility, allowing conversions of non-homologated production cars into compliant rally vehicles using approved kits for safety and performance components, further democratizing the sport. In October 2025, the FIA approved Group E-Rally5 as an electric variant, featuring electric powertrains with battery capacities up to or over 60 kWh, , and a minimum of four seats, supporting sustainable growth in the rally pyramid. This evolution supports the pyramid's goal of sustainable growth, with Rally5 events often serving as feeders for FIA rounds and beyond.

Overview

Definition and Purpose

Group Rally5 is a two-wheel-drive (2WD) category within the FIA's , serving as the entry-level class for rally cars homologated under Appendix J, Article 260 of the , with the Rally5-Kit subcategory regulated under Article 260B. Introduced in 2019, it replaced the previous R1 subcategory in Group R to streamline and modernize the classification system for international . This category emphasizes vehicles derived from production models, with limited modifications to ensure safety and competitiveness at an introductory level. The primary purpose of Group Rally5 is to lower the financial and technical in , making the sport accessible to amateur and junior drivers through cost-effective regulations focused on production-based components. By prioritizing simplicity and affordability, it targets regional and national competitors, fostering grassroots participation and providing a clear pathway for progression within the . This aptitude level, designated as "Access," supports one-make series and local assemblies to promote global development without requiring extensive engineering resources. Key performance controls include a minimum of 6 kg/hp to maintain balanced and controlled speeds suitable for beginners, alongside mandatory 2WD configurations for front- or setups. under Article 260B allows for Rally5-Kit variants, enabling national sporting authorities to approve conversions of standard production cars with predefined modification kits, further enhancing accessibility.

Historical Development

Group Rally5 emerged as the successor to the R1 class within the FIA's Group R regulations, which were first introduced in to provide a kit-based framework for production-derived rally cars, focusing on naturally aspirated two-wheel-drive vehicles as an accessible entry point for competitors. This class addressed the need for cost-effective modifications to standard cars, building on the safer and categories that followed the FIA's 1986 ban on the high-risk regulations after a series of fatal accidents, including the deaths of and Sergio Cresto during the . A pivotal milestone occurred in June 2018 when the FIA's World Motor Sport Council approved the initiative, renaming and restructuring rally categories to modernize access-level competition, with Rally5 officially replacing R1 and full implementation beginning in 2019. This evolution shifted from Group R's flexible kit approach toward Rally5's more standardized process, emphasizing production-based vehicles to lower barriers for newcomers while maintaining safety and performance consistency. In 2024, the FIA introduced the Rally5-Kit update, permitting conversions of production cars equipped with turbocharged 1.6-liter or naturally aspirated 2-liter engines, further broadening eligibility without requiring full . The Rally5 category formed the base of the 2019 Rally Pyramid restructuring, which streamlined the hierarchy from elite Rally1 at the top to entry-level Rally5, aiming to boost global participation by simplifying progression paths and adapting to changes in an era still recovering from the post-Group B decline in manufacturer involvement and competitor numbers. Existing cars homologated under the R1 class were grandfathered into Rally5, allowing continued use, though all new builds must adhere to the updated standards to ensure ongoing accessibility and regulatory coherence.

Technical Specifications

Eligibility Criteria

Group Rally5 vehicles must be derived from series-production touring cars homologated under FIA Group A regulations, which require a minimum production of 2,500 identical units within 12 consecutive months to ensure accessibility and cost control at the entry level of the . The homologation process is managed through the FIA's Appendix J, where applications are submitted via national sporting authorities (ASNs) to the FIA using specific forms such as the VRa5-Kit for modifications, with approvals valid for 12 years after the end of production of the model and subject to fees outlined in the FIA tariff list. involves inspections by FIA technical delegates at events to verify compliance, ensuring all vehicles meet structural and safety standards before competition. Driver eligibility for Group Rally5 events is open to holders of appropriate national or international FIA competition licenses suitable for access-level rallies, with no prior professional experience required to encourage participation. Participants must adhere to FIA medical standards, including a certificate of aptitude, and age requirements vary by national authority and license grade, typically 16 years or older for drivers in international events, with co-drivers often starting at 14-16 years depending on the ASN. Modification limits emphasize safety and standardization, permitting only kit-based upgrades from FIA-approved lists, including compulsory elements like integrated roll cages (homologated by ASNs to FIA standards, with materials limited to steel up to 4mm thick or aluminum up to 12mm), fire suppression systems compliant with FIA 8865-2018, and five-point harnesses. Optional enhancements, such as one-way adjustable dampers or sequential gearboxes, must also be pre-homologated via the VRa5-Kit form and cannot alter core production components like the engine block or chassis without specific FIA approval. These restrictions maintain parity and safety while allowing conversions through the Rally5-Kit program, which enables standard two-wheel-drive production cars (up to 2.0L naturally aspirated or 1.6L forced induction engines) to be adapted to Rally5 specifications at a controlled cost of approximately €15,000-€18,000. Transitional rules support ongoing accessibility by allowing pre-existing FIA-homologated vehicles from the former Group R1 category (renamed Rally5 in 2020) to remain eligible under their original approvals until the end of their validity period, tied to the model's production lifecycle plus up to 12 years post-production. The introduction of the Rally5-Kit in 2024 facilitates conversions from unmodified production cars, bridging older stock to new grassroots entries without a strict cutoff, though performance balancing via air restrictors and minimum weights applies to all.

Performance and Design Regulations

Group Rally5 vehicles are governed by strict performance and design regulations outlined in the FIA's Appendix J, Article 260 (standard Rally5) and Article 260B (Rally5-Kit), which emphasize affordability, safety, and parity while deriving from production car architectures. These rules limit engine configurations to ensure power outputs remain accessible for entry-level competitors, capping at approximately 160-180 horsepower through mandatory electronic and air restrictors. Standard Rally5 engines must feature a maximum of four cylinders, with options for up to 1,600 cm³ normally aspirated or up to 1,333 cm³ supercharged/turbocharged units; Rally5-Kit expands to up to 2,000 cm³ naturally aspirated (with restrictor if exceeding 170 hp) or 1,620 cm³ , all homologated via the FIA's VRa form to maintain series-derived components like pistons and crankshafts. The is restricted to , with being the preferred configuration to align with common production layouts, prohibiting any four-wheel-drive conversions. Gearboxes are limited to a sequential or dog-engagement type with no more than five forward speeds plus reverse, and differentials are confined to basic mechanical limited-slip units without active or electronic controls. This setup prioritizes simplicity and cost control, ensuring that power delivery remains predictable for novice drivers while adhering to a minimum diameter of 183 for durability. Chassis and body designs must retain a production silhouette, utilizing the production steel monocoque structure that complies with the original manufacturer's specifications, with allowances for limited reinforcements at suspension points using steel up to 4 mm thick or aluminum up to 12 mm. The minimum vehicle weight is set at 1,030 kg for normally aspirated variants (or higher for forced induction; excluding crew but including 160 kg ballast simulation, verified with or without fluids as specified) to enforce a power-to-weight ratio of at least 6.4 kg/hp, verified through dynamometer testing during homologation and scrutineering. Aerodynamic modifications are minimal, restricted to basic front and rear spoilers without adjustable elements, and the overall body must accommodate four seats per Group A standards. Safety regulations mandate a full FIA-homologated with minimum tube dimensions of 45 mm x 2.5 mm for main structures, integrated five-point harnesses, and seats homologated to FIA standards (e.g., 8855-2021) with minimum weight exceeding 10 kg. Hydraulic handbrakes are required, and tanks are limited to 30 liters capacity using FIA-approved baffled units to control costs and refueling logistics. Tires must be selected from FIA-homologated rally lists, fitted to rims ranging from 13 to 15 inches, with specifications limited to 6-inch width on 15-inch diameters (minimum 8 kg) and asphalt to 6.5-inch on 16-inch (minimum 7.5 kg) for balanced grip without excessive specialization. These measures collectively define the performance envelope, balancing competitive viability with enhanced driver protection.

Competitions and Usage

FIA World Rally Championship Involvement

Group Rally5 cars are eligible to participate in FIA World Rally Championship (WRC) events, provided they are homologated from January 1, 2019, and conform to the 2025 Appendix J, Article 260 specifications. However, these vehicles do not compete in the premier WRC category, which is reserved for Rally1 cars, nor in WRC2, limited to Rally2 homologation. Instead, Rally5 cars are eligible in the RC5 class within WRC events, providing an entry-level opportunity for production-derived vehicles to gain experience on WRC stages as a pathway for emerging talent, separate from the WRC3 support championship which is reserved for Rally3 cars. Rally5 cars also play a role in pre-event activities, including shakedowns and testing, which are integral to WRC preparation. Shakedowns, conducted the day before the ceremonial start, provide a final opportunity to fine-tune setups on a short similar to the rally's terrain, with Rally5 entrants subject to the same scrutineering and tyre allocation rules as higher categories—such as up to 12 gravel tyres. Testing is restricted to one day per driver and seven days annually across all categories, ensuring equitable access while Rally5 vehicles must comply with standards for reconnaissance cars. Regulatory alignment for Rally5 in WRC events mandates strict adherence to WRC-specific appendices in the , including Appendix J for technical conformity and Appendix L for administrative requirements. For rallies, setups permit one tyre specification with two compounds, allowing eight alternate compound tyres, while tarmac events require tyres with a minimum tread depth of 1.6 mm over three-quarters of the surface. considerations limit Rally5 participation to select stages, governed by general WRC protocols under Article 53 and Appendix III, emphasizing access-level protections for lower-powered cars without dedicated high-speed barriers. Introduced in 2019, Group Rally5 replaced the prior Group R1 designation in the FIA , standardizing two-wheel-drive entry-level competition under a unified technical framework. This shift aligned with the FIA's restructuring to lower barriers for juniors, though specific entry growth metrics in support categories remain tied to overall participation. Rally5 vehicles must meet performance and design regulations outlined in Appendix J, such as engine and limits, to ensure parity in mixed-class events. Rally5 cars are also eligible in support series like the FIA WRC Masters Cup. For 2025, enhancements to Rally5-Kit rules, effective from homologations dated January 1, 2024, under Appendix J Article 260B, expand eligibility for kit-converted production cars, promoting broader accessibility in support rallies without introducing hybrid elements. These updates include provisions for removable underbody protections and standardized rim sizes—6" x 15" for and 6.5" x 16" for tarmac—to facilitate in entry-level while maintaining cost controls.

Regional and National Applications

Group Rally5 serves as a core class in various FIA regional championships, particularly within the FIA (ERC), where it features prominently in the junior categories alongside Rally4 vehicles to support emerging talent development. In the ERC, Rally5 cars are eligible for events under the streamlined ERC Junior structure, which emphasizes for younger drivers through mandatory quotas that prioritize participants under 25 years old. This integration helps bridge to higher levels, with Rally5 forming a key component of the production-based machinery allowed across the championship's diverse rally formats, including and asphalt stages. Similarly, in the FIA (APRC), Rally5 is incorporated into access events and junior development programs, aligning with the championship's focus on regional talent pipelines and sustainable growth in and . These applications enforce FIA Regional Rally Car (RRC) specifications, ensuring Rally5 vehicles meet standardized technical eligibility for international while adapting to local event conditions. Junior quotas in APRC events often mandate Rally5 participation to foster skill progression, contributing to the overall pyramid structure that feeds into global series. At the national level, Rally5 has been adapted as an entry-level division in several countries, with localized rules enhancing accessibility. In 's Championnat de France des Rallyes, Rally5 vehicles, such as the Rally5, compete in the and Asphalt categories, where they have secured multiple championships and serve as the primary option for two-wheel-drive entrants. These national series incorporate tailored tire and fuel regulations to suit domestic conditions, promoting widespread participation while maintaining FIA standards. In the United Kingdom's (BRC), Rally5 designates the BRC5 category, forming the foundation for junior and production-based classes, with no control tire requirements to encourage broad engagement across the season's mixed-surface rounds. Participation in Rally5 has shown steady growth through 2025, driven by its role in events that provide pathways to regional and international competition. For instance, the 2025 Rallye Monte-Carlo featured 12 Rally5 entries, highlighting its increasing presence in high-profile national and regional rallies as an affordable stepping stone. Emphasis on these lower-tier events has helped expand the class's footprint, with Rally5 vehicles emphasizing cost-effectiveness to attract new competitors and sustain development from local series upward. Regional variations in Rally5 applications include allowances for evolutions based on the formula, the class's predecessor, which some areas adapt for compatibility with existing fleets while adhering to updated FIA technical regulations. This has led to challenges, such as uneven manufacturer involvement, prompting greater dependence on third-party suppliers for parts and development in less-supported markets.

Notable Examples

Homologated Vehicles

Group Rally5 vehicles are primarily based on compact production hot hatches, ensuring accessibility for entry-level rally competitors while meeting FIA homologation requirements for two-wheel-drive configurations. The class emphasizes front-wheel-drive layouts with optimized to enhance handling on and tarmac stages. As of 2025, several Rally5 models are homologated by the FIA, with updates published annually in the official homologation lists. Among the key models, the Rally5, developed by in collaboration with Ford, offers a 1.0L turbocharged three-cylinder delivering approximately 150 hp, emphasizing reliability and cost-effectiveness for junior drivers. Assembled using OMSE kits, it utilizes a compact with , McPherson suspension, and ventilated discs, optimizing 2WD traction through balanced weight distribution around 1,030 kg minimum. The Renault Clio Rally5, homologated in 2020, features a supercharged 1.3L producing around 180 hp with a five-speed sequential gearbox, designed for versatility across rally surfaces. Produced by with production numbers meeting FIA thresholds, it incorporates McPherson front suspension and torsion beam rear for stable handling in 2WD setup. Other examples include the Sport Rally5-Kit, a naturally aspirated variant with a 1.6L limited to 1600 cm³ capacity, providing an affordable option for regional events through approved kit conversions. Additionally, select older Group R1 carryovers such as the R1 remain eligible with minimal updates to meet Rally5 criteria. Manufacturer involvement is predominantly European, with Ford and leading development, supplemented by kit suppliers like and R-Technology for customization. These vehicles prioritize compact designs with aesthetics, ventilated disc brakes, and suspension systems tuned for 2WD dynamics, ensuring broad accessibility while adhering to production-based .

Key Teams and Drivers

Toksport WRT, a prominent Turkey-based team, has been instrumental in Group Rally5 competitions through its organization of the ERC Clio Trophy series, utilizing identical Renault Clio Rally5 cars on Michelin tires across multiple (ERC) events. The program, launched in , has delivered several victories and provided arrive-and-drive opportunities for young drivers, enabling cost-effective participation with prizes including progression to higher categories like Rally4. M-Sport, via its affiliate operations such as M-Sport Poland, supports Rally5 development by preparing and supplying Rally5 vehicles to customer teams and privateers in regional and ERC events, fostering talent pipelines through partnerships like the FIA Rally Star initiative. These efforts emphasize accessible engineering for entry-level 2WD rally cars, helping teams maintain competitive edges without excessive investment. Among key drivers, Italian Andrea Mabellini stands out as the 2021 ERC Trophy by WRT champion, where he secured three wins before advancing to Rally4 machinery for full ERC campaigns in 2022, demonstrating the category's role in career progression. Similarly, French driver Tom Pellerey claimed the 2024 French Two-Wheel Drive Gravel Rally Championship title in a Rally5, marking the third different winner in four years for the model and highlighting its reliability in national junior applications. Finnish driver Roope Korhonen exemplifies pathways from junior rallying to elite levels, having built experience in lower FIA categories before securing the 2023 WRC-3 title and achieving a maiden WRC2 victory at the 2025 Secto Rally Finland, with ongoing ERC appearances in higher-spec cars. Rally5 participants often feed into the FIA Junior WRC and Rally Star programs, where success in events like the Junior ERC—contested in Rally4 and Rally5 machinery—can lead to WRC opportunities, as seen with 13 rookies registered for the 2025 season. Group Rally5 remains privateer-dominated, with teams operating on modest seasonal budgets under €100,000, reliant on sponsorships from tire suppliers like for series-specific support, which lowers barriers for emerging talents. In , diversity is growing through initiatives like the WRC Promoter's Beyond Rally Women's Driver Development Programme, which selected 15 female finalists—including participants targeting Rally5 levels—for training, with drivers like Raftery competing in ERC4 classes that encompass Rally5 vehicles.

References

Add your contribution
Related Hubs
User Avatar
No comments yet.