Hubbry Logo
GWR 1500 ClassGWR 1500 ClassMain
Open search
GWR 1500 Class
Community hub
GWR 1500 Class
logo
8 pages, 0 posts
0 subscribers
Be the first to start a discussion here.
Be the first to start a discussion here.
GWR 1500 Class
GWR 1500 Class
GWR 1500 Class
View on Wikipedia
from Wikipedia

Great Western Railway 1500 Class
No. 1502 at Didcot 1957
Type and origin
Power typeSteam
DesignerFrederick Hawksworth
BuilderSwindon Works
Order numberLot 373
Build date1949
Total produced10
Specifications
Configuration:
​
 • Whyte0-6-0PT
 • UICCh2tg
Gauge4 ft 8+1⁄2 in (1,435 mm) standard gauge
Driver dia.4 ft 7+1⁄2 in (1.410 m)
Minimum curve3+1⁄2 chains (231 ft; 70 m)
Wheelbase12 ft 10 in (3.91 m)
Loco weight58 long tons 4 cwt (130,400 lb or 59.1 t) (62.9 short tons)
Fuel typeCoal
BoilerGWR Standard No. 10[1]
Boiler pressure200 lbf/in2 (1.4 MPa)
CylindersTwo, outside
Cylinder size17.5 in × 24 in (444 mm × 610 mm)
Valve gearWalschaerts
Valve typepiston valves
Performance figures
Tractive effort22,515 lbf (100.15 kN)
Career
OperatorsBritish Railways, National Coal Board
Power classGWR: C
BR: 4F
Numbers1500–1509
Axle load classGWR: Red
LocaleWestern Region
WithdrawnBR: 1959–1963,
NCB: 1970
DispositionOne preserved, remainder scrapped

The Great Western Railway (GWR) 1500 Class is a class of 0-6-0PT type steam locomotive. Despite being a GWR Hawksworth design, all ten (nos 1500–1509) were completed under the administration of the Western Region of British Railways in 1949, just after Nationalisation.

Overview

[edit]

Coming from a railway company with a well-developed standardisation policy, the 15xx was an unconventional break. Unlike almost all previous panniers they had outside cylinders, Walschaerts valve gear, and a very short wheelbase of 12 ft 10 in (3.91 m) to go round curves of 3.5 chains (231 ft; 70 m). Above footplate level they were very similar to the 9400 class, and shared the same Standard No. 10 boiler. The major difference was below the (very small) footplate, where they resembled the USATC S100 Class that the GWR and other railways had used during the Second World War.

Although a functional design, the class had limited usefulness as they were route-restricted by their high weight and were unsuitable for fast running because of their short wheelbase. Largely confined to empty stock workings at London Paddington station, their lives were short; for example 1509 lasted barely ten years in BR service. Four of the class, 1506 to 1509, were based in Wales, Newport Pill, Ebbw Junction & Cardiff Canton, 1508[2] was withdrawn from that last shed. Like the 1600 and 9400 classes, their construction now appears to have been of doubtful value.

The onset of dieselisation and the decline in traffic on the railway network meant the 1500s were withdrawn and scrapped while still in workable condition. However No. 1501 has seen regular use at the Severn Valley Railway in preservation, much longer than its life in BR ownership.

Year Quantity in
service at
start of year		 Quantity
withdrawn		 Locomotive number(s)
1959 10 1 1509
1960 9 0 –
1961 9 2 1501-2
1962 7 2 1505/8
1963 5 5 1500/3-4/6-7

Preservation

[edit]
1501 after restoration in 2012 and wearing the early BR lined black scheme

1501 was one of the first of the class to be withdrawn in 1961, but was sold along with 1502 and 1509 to the National Coal Board for use at Coventry Colliery. The three locos were sent to Andrew Barclay Sons & Co., in Kilmarnock, Scotland for overhaul before delivery to the NCB. All three locomotives were purchased in 1970 by the Severn Valley Railway. Locomotives 1502 and 1509 were used as sources of spares for the restoration of 1501. The remains of 1502 and 1509 were scrapped at Cashmore's, Great Bridge in October 1970.

In 2006 No. 1501's boiler certificate expired and it was withdrawn from traffic. The locomotive was overhauled and steamed again in August 2012. It was repainted in British Railways lined black colour scheme with the early BR emblem on its tanks, a livery not normally used on shunting locomotives but carried by classmates 1501 and 1503 while at Old Oak Common.[3] It was withdrawn from service again at the start of 2023 and will require a full overhaul before any further use. [4]

See also

[edit]
  • GWR 0-6-0PT – list of classes of GWR 0-6-0 pannier tank, including table of preserved locomotives

References

[edit]
[edit]
Revisions and contributorsEdit on WikipediaRead on Wikipedia

GWR 1500 Class

View on Grokipedia
from Grokipedia
The GWR 1500 Class was a class of ten pannier tank steam locomotives designed by Frederick Hawksworth as heavy shunters for the Great Western Railway (GWR), featuring outside cylinders and in a departure from traditional GWR inside-cylinder designs, though all examples were built by the at in 1949. These locomotives, numbered 1500–1509 and classified as 4F, measured 4 feet 7.5 inches in driving wheel diameter, with a boiler pressure of 200 psi, 17.5-inch by 24-inch outside cylinders, and a tractive effort of 22,515 pounds, enabling them to handle demanding shunting tasks such as moving long trains of empty carriages. Their short 12-foot-10-inch wheelbase and lack of a running plate facilitated tight curve navigation in yards, while welded construction and a 1,350-gallon water capacity supported extended operations without frequent servicing. Primarily allocated to Old Oak Common depot for shunting passenger stock to and from London Paddington, some also operated in the Newport area on freight and local duties. Introduced amid post-World War II shortages, the class drew from earlier GWR designs like the 94xx but incorporated innovations for maintenance ease, with drawings dating back to 1944. Weighing 58 tons 4 , they proved versatile for yard work and occasional trips, though their specialized role limited broader deployment. Withdrawals began in 1959 with 1509, continuing until the last four were retired by December 1963 amid the dieselization of British Railways. Three examples (, , and 1509) were sold to the for industrial use, with only No. preserved today at the (as of 2025).

Background and Design

Development Context

The GWR 1500 Class was designed by Frederick William Hawksworth, the Chief Mechanical Engineer (CME) of the Great Western Railway (GWR) from 1941 to 1948, marking it as the final new pannier tank class introduced under his tenure. Conceived in the waning years of the GWR's independent operation, the class was ordered on December 31, 1947, under GWR Lot 373, just before the of British railways on January 1, 1948, although construction did not commence until after that date. This timing positioned the 1500 Class as a transitional design, developed amid growing pressures from dieselization initiatives that ultimately rendered steam shunting locomotives like these somewhat obsolete by the time of their completion in 1949. The primary purpose of the 1500 Class was to serve as a heavy shunting capable of operating continuously for 24 hours without requiring pit servicing for maintenance, addressing the demands of intensive yard work at major depots such as near and Newport. Its short of 12 feet 10 inches enabled negotiation of tight curves with a minimum radius of 3.5 chains (approximately 231 feet), making it suitable for congested freight and carriage sidings where maneuverability was essential. This focus on reliability and ease of access reflected the GWR's need for efficient, low-maintenance engines to handle the increasing volume of shunting tasks in the post-war era. Drawing influences from earlier GWR pannier tank designs such as the 1366 and 5700 classes as well as the Transportation Corps (USATC) S100 class, the 1500 Class incorporated modifications for improved performance in shunting roles, including the adoption of outside cylinders—a departure from the typical inside-cylinder configuration of most GWR panniers. This arrangement, inspired by the S100's design, enhanced accessibility to mechanical components and reduced maintenance downtime, allowing for quicker inspections and repairs without extensive disassembly, which was particularly advantageous for round-the-clock operations. Despite these advancements, the design's steam-based technology faced rapid obsolescence due to the parallel advancement of diesel shunters, which offered greater efficiency and lower operating costs.

Key Design Features

The GWR 1500 Class locomotives featured a pannier tank (PT) , which omitted leading or trailing wheels to enhance stability and reduce the risk of on tight curves with radii as small as 3.5 chains (231 feet). This configuration, combined with a notably short of 12 feet 10 inches (3.91 m), was specifically engineered for superior maneuverability in confined shunting yards and curved sidings, allowing the locomotives to navigate sharp turns more effectively than larger GWR tank classes. A key innovation was the adoption of outside cylinders measuring 17.5 inches by 24 inches, paired with , marking a departure from the GWR's traditional inside-cylinder designs prevalent in earlier pannier tanks. This external placement facilitated easier access for valve maintenance and repairs, particularly beneficial for the intensive shunting duties these locomotives were intended for, as it eliminated the need to dismantle internal components during servicing. The pannier tanks were strategically positioned directly over the firebox, promoting a low center of gravity for improved stability during heavy shunting operations while providing substantial capacity of 1,350 imperial gallons of water and 3.25 long tons of coal. This arrangement maximized fuel and water storage without compromising the locomotive's compact footprint, enabling extended periods of operation without frequent replenishment. The frame employed high-strength steel plates in a predominantly welded construction, rather than the riveted designs of prior GWR locomotives, enhancing durability and rigidity under the stresses of repeated heavy loads and impacts common in yard work. Complementing this were unique short overhangs at both ends, achieved by the absence of a running plate and the compact tank positioning, which further minimized the locomotive's overall length and reduced vulnerability to buffer damage or on restricted tracks. In terms of power classification, the class was rated 'C' under GWR standards and equivalent to BR's 4F category, reflecting its capability for medium-powered shunting and light freight tasks.

Construction and Specifications

Building Details

The GWR 1500 Class locomotives, numbering ten in total (1500–1509), were constructed entirely at Swindon Works following the nationalization of the Great Western Railway on 1 January 1948, under the auspices of British Railways Western Region. Designed by Frederick Hawksworth as a final GWR project, the class was authorized under Lot 373, with production commencing shortly after the transition to BR administration. All units adhered strictly to this lot's specifications, ensuring uniformity in design and construction without any production variations between individual locomotives. The standard GWR numbering sequence was retained for the class, reflecting continuity in identification practices despite the change in ownership. Production followed a sequential timeline at . The first locomotive, No. 1500, was outshopped in June 1949, marking the class's entry into the post-nationalization era of manufacturing. Subsequent units were completed progressively: Nos. 1501 and 1502 in , Nos. 1503–1505 in August, and Nos. 1506–1509 in September, culminating with No. 1509 in September 1949, spanning approximately four months. This schedule allowed for efficient assembly using established facilities. The locomotives featured welded construction for key components. Upon outshop, all units received the British Railways lined black with the early BR emblem on the side tanks—a scheme unusual for shunting locomotives. This finish predominated from 1949 until 1957, after which examples incorporated the later BR crest during overhauls for modernization alignment. Numbering was applied in brass digits on the cab sides, consistent with BR Western Region conventions while preserving the original GWR series.

Technical Specifications

The GWR 1500 Class locomotives were equipped with the GWR Standard No. 10 , operating at a of 200 lbf/in², featuring a total heating surface of 1,470 sq ft, a grate area of 10 sq ft, and a incorporating 180 tubes. The class utilized two outside cylinders measuring 17.5 in × 24 in, delivering a of 22,515 lbf at 85% of , with employed for the motion. Key dimensions included driving wheels of 4 ft 7½ in diameter, a total weight of 58 long tons 4 cwt, and a length over buffers of 28 ft 2½ in. Fuel and water capacities comprised 3.25 long tons of coal and 1,350 imp gal of water, while the axle load stood at 19 long tons 8 cwt (approximate). The locomotives adhered to the standard gauge of 4 ft 8½ in, with adhesion weight of 58 long tons 4 cwt (total weight).
SpecificationDetails
Boiler TypeGWR Standard No. 10
Boiler Pressure200 lbf/in²
Total Heating Surface1,470 sq ft
Grate Area10 sq ft
Superheater Tubes180
CylindersTwo outside, 17.5 in × 24 in
Tractive Effort22,515 lbf (at 85% boiler pressure)
Driving Wheel Diameter4 ft 7½ in
Total Weight58 long tons 4 cwt
Length over Buffers28 ft 2½ in
Coal Capacity3.25 long tons
Water Capacity1,350 imp gal
Axle Load19 long tons 8 cwt (approximate)
Gauge4 ft 8½ in (standard)
Adhesion Weight58 long tons 4 cwt

Operational History

Service on British Railways

The GWR 1500 Class locomotives entered service on British Railways in 1949, shortly after , and were primarily employed on the Western Region for shunting and light freight duties during the transition from to diesel traction. These tank engines, designed with a short to navigate tight curves in busy terminal areas, proved effective for handling empty coaching stock (ECS) workings, particularly between yard and . Their robust of 22,515 lbf enabled them to manage long trains of empty stock, making them a staple for passenger-related shunting tasks amid the post-war rail network's demands. Most of the class was allocated to (shed code 81D), where they performed heavy shunting in the major yard, supporting both freight and passenger operations. A smaller number, locomotives 1506–1509, were allocated to sheds from introduction, including Newport Pill (86B), Cardiff Canton (86C), and Newport Ebbw Junction (86A), for similar yard duties. The class reached its peak utilization in the mid-1950s, when power was still prevalent but facing increasing diesel competition, allowing the 1500s to fill critical roles in shunting both freight wagons and passenger stock across key Western Region facilities. Livery during this period began with British Railways unlined black upon entry in 1949, but a few examples received the briefly in the 1950s, reflecting transitional BR Western Region practices for certain pannier tanks.

Post-Nationalization Use

Following their withdrawal from British Railways service, three locomotives of the GWR 1500 Class—numbers , , and 1509—were sold to the (NCB) in early 1961 for industrial shunting duties at Coventry Colliery (also known as Keresley Colliery) near . These engines were selected due to their compact design and suitability for tight clearances in coal yard operations, where they handled wagon movements within the colliery sidings and along a two-mile to Three Spires Junction. Prior to entering NCB service, the trio underwent overhauls at W.G. Bagnall's works in and Andrew Barclay Sons & Co. in , , to prepare them for industrial conditions. The locomotives served the NCB for approximately eight years, with 1501 operating until September 1969, after which it was replaced by diesel shunters. Numbers and 1509 continued in use slightly longer, providing spare parts to support 1501 before their own withdrawal and scrapping in October 1970. Adaptations for industrial work were minimal, primarily consisting of repainting into an unlined maroon livery and likely adjustments to lighting for non-railway operations, with no evidence of major mechanical rebuilds. This limited service reflected the class's robustness in low-speed shunting but was curtailed by the broader shift away from steam in the late , driven by rising maintenance costs and dwindling spare parts availability amid dieselization. The last NCB withdrawal of a 1500 Class occurred around 1970, marking the end of their industrial career.

Withdrawal and Legacy

Disposal Process

The withdrawal of the GWR 1500 Class locomotives from British Railways (BR) service began in August 1959 with No. 1509, which was taken out of traffic at Newport Ebbw Junction shed while still under 10 years old. Subsequent withdrawals followed rapidly due to the BR modernisation plan, which prioritized diesel locomotives for shunting duties; the more economical 350 hp diesel shunters, such as the Class 08, rendered the steam-powered 1500 Class obsolete despite their relatively short service lives averaging 12–14 years. By December 1963, the entire class had been withdrawn, with the final examples (Nos. 1500, 1503, 1506, and 1507) removed from shed. For instance, No. was withdrawn in January 1961 after 11 years and 5 months of service. The primary reasons for the class's early withdrawal included the rapid adoption of diesel shunters, which offered lower operating costs and greater reliability for yard work, alongside the 1500 Class's limited annual mileage—a consequence of their specialized shunting role that contributed to their quick obsolescence before reaching full mechanical lifespan. No locomotives were exported; instead, three were sold to the (NCB) between 1960 and 1961 for industrial use at Coventry Colliery, specifically Nos. 1501, 1502, and 1509, which were overhauled at Andrew Barclay Sons & Co. in before delivery. These NCB locomotives remained in service until 1969–1970, with Nos. 1502 and 1509 ultimately providing spare parts to sustain No. 1501's operation. The remaining locomotives were scrapped shortly after withdrawal, with the majority processed in the early . For example, Nos. 1502 and 1509 were cut up at Cashmore's scrapyard in Great Bridge in October 1970 following their cannibalization for parts. Other members of the class, including Nos. , 1503, 1504, 1506, 1507, and 1508, met similar fates at various BR-approved scrapyards, such as those operated by Cashmore's, with disposals completed by 1964 to clear storage at sites like .

Performance Evaluation

The GWR 1500 Class demonstrated notable strengths in shunting operations, particularly its high that enabled effective handling of short-haul tasks such as moving long rakes of empty coaching stock over distances up to 57 miles on minimal water supplies. Crews appreciated its reliability, as the design allowed for 24-hour shunting duties without the need for frequent pit oiling, contributing to its robust performance in confined yard environments. Despite these advantages, the class faced significant limitations stemming from its heavy weight of 58 tons 4 cwt and short 12-foot-10-inch , which resulted in route restrictions under the GWR's Red classification, barring it from many lighter branch lines and yards. The compact design, including long overhangs at the ends, further constrained its versatility on sharp curves, while the short contributed to mediocre overall performance, including poor starting characteristics due to limited . Additionally, its higher fuel demands compared to emerging diesel alternatives undermined long-term economic viability in an era of modernization. Historical assessments highlight the 1500 Class as a product designed too late in the steam era, with all ten locomotives entering service in 1949 under British Railways, just as dieselization accelerated. Trials revealed subpar acceleration relative to established predecessors like the 5700 Class, rendering it less competitive for general shunting, and by the mid-1950s, it was deemed obsolete against 350 hp BR Class 08 diesel shunters that offered lower operating costs and greater flexibility. The class's brief service life of around 11 years underscored the challenges of transitioning from steam, with withdrawals beginning in 1959. In legacy terms, the 1500 Class symbolizes the GWR's final attempts at steam innovation under Frederick Hawksworth amid rapid electrification and diesel adoption, its short lifespan illustrating the inefficiencies that hastened steam's decline on British Railways.

Preservation

The Preserved Locomotive

No. 1501, the sole surviving locomotive of the GWR 1500 Class, was withdrawn from British Railways service in January 1961 after primarily working as a shunter at Old Oak Common depot. It was then sold to the in February 1961 and operated at Keresley Colliery near until becoming redundant in September 1969. The purchased the locomotive in 1970, and it arrived by road at on 17 October 1970, having sustained minor damage during transit. Restoration efforts commenced soon after arrival, initially at before moving to in 1977, with key milestones including the boiler lift on 30 April 1982 and re-wheeling on 9 September 1983. Further work, including retubing in 2001–2002 and re-tyring in 2004, culminated in the first steaming on 29 May 1997, allowing it to enter passenger service on the in September 1997. It hauled regular passenger trains, earning the nickname "the " among volunteers for its powerful performance despite its compact size, and accumulated approximately 98,933 miles in preservation by the end of 2019. The also made guest appearances at other heritage lines, such as in 1998 and the Railway in 1999. A major overhaul began in late 2006, with the locomotive withdrawn from traffic on 31 December 2006, and it returned to service after completion on 15 August 2012. No. participated in the Railway's 50th anniversary celebrations in 2020, operating during the preserved line's milestone events. It incorporated components recovered from its scrapped class sisters to support ongoing maintenance. The certificate expired on 2 January 2023, leading to withdrawal after its final passenger workings. As of November 2025, No. remains out of service and is stored under cover at Locomotive Works, where preliminary conservation work by volunteers is underway in preparation for a full overhaul. The Tank Association, its owning group, intends to return the to operational status following the overhaul, though no specific timeline has been confirmed.

Spares and Artifacts

Following the withdrawal of locomotives Nos. 1502 and 1509 in , along with No. , the trio was sold to the for industrial use at Colliery. While No. underwent overhaul by Andrew Barclay Sons & Co., Nos. and 1509 served primarily as donors of spare parts to support its operation, including components such as wheels and motion assemblies. These locomotives remained in storage until October 1970, when the remnants of Nos. and 1509 were scrapped at Cashmore's yard in Great Bridge, West Midlands, after their usable parts had been salvaged. The recovered spares from Nos. 1502 and 1509 played a key role in the long-term preservation of No. 1501 at the Severn Valley Railway (SVR). Specific items, such as a replacement return crank from No. 1509, were fitted in 2020, ensuring compatibility with the class's unique outside cylinder design. Remaining components continue to be stored at the SVR's Bewdley facility for potential future maintenance needs. Legacy items include technical drawings of the 1500 Class, such as engine diagrams for the 0-6-0T configuration with outside Walschaerts valve gear, archived in the Swindon Works collection at the National Railway Museum. These resources support ongoing research and model-making efforts, though physical scale models of the class are primarily modern reproductions rather than historical artifacts.
Add your contribution
Related Hubs
User Avatar
No comments yet.