Hubbry Logo
Trailing-arm suspensionTrailing-arm suspensionMain
Open search
Trailing-arm suspension
Community hub
Trailing-arm suspension
logo
8 pages, 0 posts
0 subscribers
Be the first to start a discussion here.
Be the first to start a discussion here.
Trailing-arm suspension
Trailing-arm suspension
Trailing-arm suspension
View on Wikipedia
from Wikipedia
Trailing-arm (or link) landing gear leg on a Cessna 404 aircraft

A trailing-arm suspension, also referred to as trailing-link, is a form of vehicle suspension. In a motor vehicle it places one or more horizontal arms (or "links") perpendicular to and forward of the axle on the chassis or unibody, which are connected to the axle or wheels with pivot joint(s). These are typically used on the rear axle or wheels of vehicles, but also found in both front and main landing gear of aircraft.

A "semi trailing-arm" (or semi trailing-link) is a common form of independent rear suspension on automobiles, particularly those with front wheel drive (where it allows a flatter rear floor pan).

Leading arms are similar horizontal arms, perpendicular to the axle, but connecting the wheels to the vehicle structure via pivot joints to the rear of them. These are typically used on the front axle or wheels, as on the Citroën 2CV and its derivatives, and on the Citroën DS, as well as on the M422 Mighty Mite jeep.

Types

[edit]
Trailing arm rear suspension of FF cars
Rear suspension of Renault 4 and Renault 5
Semi-trailing arm suspension

Trailing-arm

[edit]

Trailing-arm designs in live axle setups often use just two or three links and a Panhard rod to locate the wheel laterally. A trailing arm design can also be used in an independent suspension arrangement. Each wheel hub is located only by a large, roughly triangular arm that pivots at one point, ahead of the wheel. Seen from the side, this arm is roughly parallel to the ground, with the angle changing based on road irregularities. A twist-beam rear suspension is very similar except that the arms are connected by a beam, used to locate the wheels and which twists and has an anti-roll effect.

Some aircraft also use trailing arms in their landing gear, with oleo struts for shock absorption. A trailing arm landing gear results in smoother landings and a better ride when taxiing compared to other types of landing gear.[1]

Semi-trailing arm

[edit]

A semi-trailing arm suspension is a supple independent rear suspension system for automobiles where each wheel hub is located only by a large, roughly triangular arm that pivots at two points. Viewed from the top, the line formed by the two pivots is somewhere between parallel and perpendicular to the car's longitudinal axis; it is generally parallel to the ground. Trailing-arm and multilink suspension designs are much more commonly used for the rear wheels of a vehicle where they can allow for a flatter floor and more cargo room. Many small, front-wheel drive vehicles feature a MacPherson strut front suspension and trailing-arm rear axle.

See also

[edit]

References

[edit]
Revisions and contributorsEdit on WikipediaRead on Wikipedia

Trailing-arm suspension

View on Grokipedia
from Grokipedia
Trailing-arm suspension is a suspension configuration where one or more longitudinal arms, known as trailing arms, pivot from a point on the forward of the to connect to the hub or , primarily allowing vertical movement while constraining fore-aft motion. This design can be implemented as an , where each moves separately, or as part of a dependent system with a solid linking both wheels. The arms typically incorporate bushings at the pivot points to absorb vibrations and handle forces from , braking, and cornering, often paired with coil springs, springs, or torsion bars for load support and shock absorbers for damping. In independent trailing-arm setups, common in rear suspensions of passenger cars, the geometry maintains near-zero camber and changes during vertical travel, providing stable handling without significant variation—typically limited to a few millimeters over typical suspension stroke. Dependent versions, such as those using a live , employ trailing arms to locate the axle longitudinally while a track bar or manages lateral positioning, ensuring the wheels remain perpendicular to the road surface under load. Key design parameters include arm length, pivot angle (near horizontal for minimal ), and spring stiffness (e.g., 18,600 N/m for balanced ride), optimized via quarter-car models to balance comfort and roadholding. This suspension type offers simplicity and low manufacturing cost, making it economical for mass-produced vehicles; however, independent forms often have higher unsprung mass than multi-link systems, potentially impacting ride quality. However, it provides limited camber gain during cornering, potentially leading to understeer, and in dependent configurations, transmits road shocks across both wheels due to the rigid axle. Trailing-arm suspensions have been widely applied since the early in economy like the , off-road vehicles for their durability over rough terrain, and modern rear-drive setups in light trucks, where variants like semi-trailing arms (angled at 50-70 degrees from horizontal) improve lateral compliance.

Introduction

Definition and Principles

Trailing-arm suspension is a suspension configuration that can be independent or dependent, in which one or more , oriented horizontally and aligned longitudinally with the , pivot at their forward end to the or body , while the hub or assembly is attached at the rearward end of the arm. This configuration allows the to "trail" behind the pivot point, enabling vertical movement to absorb road undulations while constraining the wheel's path primarily to a fore-aft direction. The is commonly applied to rear suspensions but can also appear in front applications, providing a balance of simplicity, cost-effectiveness, and packaging efficiency in . At its core, the principles of trailing-arm suspension emphasize longitudinal compliance, where the arm's flexibility—often enhanced by rubber bushings at the pivot—allows it to yield slightly under fore-aft forces from road impacts, braking, or acceleration, thereby isolating the vehicle body from harsh vibrations and improving ride comfort. Lateral stability is maintained through the arm's rigidity in the , supplemented by additional components such as a or transverse links that prevent excessive side-to-side motion under cornering loads or crosswinds. This separation of compliance directions ensures the suspension absorbs vertical and longitudinal disturbances effectively while preserving handling precision. The pivot axis of the trailing arm is typically aligned parallel to the vehicle's transverse axis, often at or near level, which governs the 's kinematic path during vertical as a centered on the pivot. As the encounters a bump, it moves upward and slightly rearward along this arc, minimizing unwanted camber or alterations and promoting consistent contact with the road surface. This contributes to stable by limiting lateral deflection without overly constraining vertical compliance. Unlike leading-arm suspensions, where the pivot is behind the wheel (with the arm leading forward to the wheel) and can induce greater body pitch under certain loads, the trailing-arm arrangement positions the pivot ahead of the wheel, which directs torque reactions to counteract rear squat during acceleration and front dive during braking, thereby enhancing overall pitch control. This design was first utilized in early 20th-century vehicles to address ride and handling challenges in emerging automobiles.

Historical Context

The concept of trailing-arm suspension emerged in the early , with roots in where trailing-arm designs were applied to landing for improved shock absorption and smoother . By the late , this configuration appeared in lighter , such as the Ercoupe, providing a compliant that minimized jolts during ground operations. In and , initial patents and prototypes explored similar pivoting arm mechanisms for vehicle wheels to handle longitudinal forces more effectively. For instance, in incorporated trailing-arm elements in their rear suspension to enhance stability at high speeds. Following , trailing-arm suspension gained traction in European automotive production, transitioning from experimental racing use to practical road car designs. pioneered the semi-trailing arm variant in the late 1950s with models like the , which featured this setup for its rear suspension to balance cost and performance. By the 1960s, expanded its application to the Neue Klasse sedans, such as the 1500 series introduced in 1962, and the 02 series in 1966, where semi-trailing arms supported the differential on a subframe for refined handling. Concurrently, the design evolved into racing contexts, with late-1960s Formula 1 cars adopting simplified trailing-arm setups at the rear to integrate with emerging stressed-skin chassis, prioritizing lightweight construction and ease of maintenance under the era's regulations. The 1970s marked a breakthrough in , as trailing-arm systems became integral to compact economy cars. Volkswagen's Golf Mk1, launched in , employed a semi-independent rear suspension with dual trailing arms linked by a torsion beam, enabling efficient packaging and cost-effective independent wheel control for front-wheel-drive layouts. This configuration proliferated in European vehicles, offering a compromise between simplicity and ride quality. By the 1990s, trailing-arm suspensions began declining in premium segments as multi-link systems offered superior camber control and adjustability, becoming the standard for performance-oriented cars from manufacturers like and . However, the design persisted into the 2020s in budget sedans, light trucks, and off-road vehicles, where its durability and low manufacturing cost remain advantageous for rugged applications.

Design and Mechanics

Key Components

The trailing arm serves as the primary in a trailing-arm suspension , functioning as a longitudinal link that pivots from a chassis-mounted point forward of the to control vertical movement and absorb longitudinal forces such as and braking. Typically constructed as a tubular or boxed beam, it connects to the hub or at its rearward end, allowing the to follow the road surface while maintaining alignment. Bushings or pivot joints at the forward attachment point enable controlled articulation, reducing by accommodating compliance in multiple planes. Supporting elements include coil springs or leaf springs mounted directly to the trailing arm, which provide the restorative force to support and isolate road irregularities from the . Shock absorbers, or dampers, are paired with these springs and attached to the arm to control oscillatory motion, dissipating energy from bumps and ensuring stable handling. Control links, such as lateral or rods, connect to the arm or hub to manage sideways forces and prevent excessive lateral shift of the , contributing to overall stability. Material selection for the trailing arm balances strength, weight, and application demands; high-strength steel, such as AISI 4130, is commonly used for its superior durability and resistance to fatigue in off-road or heavy-duty environments where impacts and torsional loads are prevalent. In contrast, aluminum alloys like 6061-T6 or 7075-T6 are favored for performance-oriented vehicles to reduce unsprung mass, improving responsiveness and without compromising structural integrity under typical loads. Assembly configurations vary by design intent: a single trailing arm per wheel is standard in independent suspension setups, allowing each wheel to articulate separately for better ride quality. In solid axle applications, paired trailing arms—one on each side—connect to a common housing, providing synchronized movement suited to load-bearing or scenarios.

Kinematics and Geometry

In trailing-arm suspension, the kinematic model describes the wheel's motion as a centered on the pivot point of the , with the radius equal to the length LAL_A. This arc path results from the 's about its fixed pivot, typically oriented longitudinally, allowing primarily vertical wheel displacement while constraining lateral and fore-aft movements. The vertical displacement zSz_S of the during by uAu_A from its static position uA0u_{A0} is approximated by zS=LA(sin⁡uA−sin⁡uA0)/cos⁡fAxz_S = L_A (\sin u_A - \sin u_{A0}) / \cos f_{Ax}, where fAxf_{Ax} is the slope of the pivot axis. This inherently produces anti-dive and anti-squat properties, particularly at the rear , where the percentage is influenced by the 's inclination θ\theta to the horizontal longitudinal axis; for a simplified model, anti-squat percentage approximates 100×tan⁡θ100 \times \tan \theta, counteracting body pitch under by directing reaction through the suspension pivot. Key geometry parameters include the instant center, height, and camber gain. The instant center lies at the intersection of the trailing arm's pivot axis with the plane or , varying slightly with suspension bump due to the arc motion, which defines the effective point for forces during dynamic events. height is typically at or near ground level for a pure trailing-arm setup, calculated as approximately 12T×BScd0\frac{1}{2} T \times BScd0 where TT is track width and BScd0=HS/RSBScd0 = H_S / R_S (with HSH_S as suspension height and RSR_S as swing arm radius), influencing load transfer and stability; adjustments via pivot slope tan⁡fAx\tan f_{Ax} can raise this height to mitigate effects. Camber gain during suspension travel is minimal or zero in a true trailing-arm configuration, as the remains to the arm throughout its arc, resulting in ϵBC1≈0\epsilon_{BC1} \approx 0 per unit vertical displacement, unlike designs with angled links that induce camber changes. Equations for bump steer minimization and wheelbase variation further characterize the system's behavior. , the unintended steering change with suspension travel, is inherently low in trailing-arm designs due to the fixed pivot geometry, with the linear coefficient ϵBS1=−fAx/RP\epsilon_{BS1} = -f_{Ax}/R_P (where RPR_P is the pivot radius) approaching zero for horizontal arms, allowing precise linkage placement to keep it under 0.5° per inch of travel. Wheelbase variation arises from the arc's longitudinal component; for small deflection angles ϕ\phi, the change ΔL\Delta L is given by ΔL=LA(1−cos⁡ϕ)\Delta L = L_A (1 - \cos \phi), shortening the effective in compression and lengthening it in rebound, typically by 1-2% over full travel in passenger vehicles to maintain stability without excessive scrub. The also affect the tire and handling under cornering by modulating scrub and alignment. The arc path induces minimal lateral scrub radius ϵBScd0,Y=HS/RS\epsilon_{BScd0,Y} = H_S / R_S, preserving uniformity and reducing tire wear, while the low camber variation ensures consistent vertical load distribution during roll. In cornering, this promotes neutral handling by keeping the instant center low, minimizing lateral force variations at the tire-road interface and enhancing grip predictability, though higher-speed turns may amplify fore-aft shifts, subtly influencing understeer tendencies.

Types

Trailing Arm

The trailing arm suspension employs a single horizontal that pivots from a forward-mounted point on the , with the carrier or attached directly at the rearward end of the arm. This setup constrains the 's motion primarily to vertical travel along an arc, making it particularly suitable for solid rear suspensions where and cost-effectiveness are prioritized. A key characteristic of this configuration is the minimal lateral forces exerted on the pivot bushing, as the arm's longitudinal orientation aligns forces from road inputs and primarily along its length. This allows for the use of softer rubber bushings at the pivot, enhancing ride compliance and reducing harshness without compromising structural integrity. The design is frequently integrated with leaf-spring systems in applications, where the springs handle vertical loads and the trailing arm manages fore-aft positioning for heavy-duty stability. In terms of , the wheel path traces a centered on the pivot, which introduces minor variations under suspension deflection but maintains consistent camber and angles. Maintenance considerations focus on the pivot bushings, which endure significant from longitudinal loads during , braking, and reaction, potentially leading to increased vibration, noise, or misalignment if not inspected regularly. Replacement typically involves pressing out worn bushings and ensuring proper alignment to restore original .

Semi-Trailing Arm

The semi-trailing arm suspension variant features a pivoted at an angle of 50 to 70 degrees from the horizontal longitudinal axis, distinguishing it from the purely horizontal trailing arm by enabling simultaneous longitudinal and lateral control in independent rear suspension systems. This angled configuration allows the arm to resist both fore-aft forces and lateral loads during cornering, contributing to more refined in rear-wheel-drive applications. A key trait of the semi-trailing arm is its inherent camber gain during body roll, where suspension compression induces negative camber at the outer wheel, counteracting the positive camber from vehicle lean and optimizing tire patch contact in corners to enhance grip and reduce uneven tire wear. This is frequently integrated with strut or coil-over shock absorbers for vertical , providing a compact and cost-effective solution for while maintaining acceptable ride quality. Notable implementations include the BMW 3 Series (E21 chassis, launched in 1975), which employed semi-trailing arms at the rear paired with coil springs and dampers to balance sporty handling with everyday usability. The Porsche 911 also utilized semi-trailing arm rear suspensions across multiple generations, leveraging the geometry for agile rear-end response in high-performance sports cars. An evolutionary advancement came with Porsche's , introduced in 1978 on the 928 model as a refined semi-trailing arm setup featuring a decoupled inner pivot bushing to minimize toe-out under braking and , thereby reducing rear-end lift and improving stability without altering the core angled arm principle.

Applications

Automotive Vehicles

Trailing-arm suspension has been widely implemented in passenger cars, particularly for rear axles in compact models seeking cost-effective independent wheel motion. In the , models produced after 1968 adopted independent rear suspension (IRS) featuring semi-trailing arms, which allowed each rear wheel to move independently for improved handling and ride comfort compared to the earlier swing-axle design. Similarly, early generations of the , starting from the first generation in 1972, utilized independent rear suspension with trailing arms and coil springs, enabling compact packaging and economical production while providing better stability over bumps than rigid axles. In trucks and SUVs, trailing-arm configurations often pair with solid axles to handle heavy loads while maintaining durability. The Ford F-Series, for instance, employs solid rear axles supported by leaf springs and trailing arms in certain setups, distributing weight effectively for towing and hauling capacities up to several thousand pounds without compromising axle alignment under stress. Modern applications in electric vehicles highlight trailing-arm suspension's adaptability to unique packaging needs, such as integrating large battery packs. The Tesla Model 3's rear suspension incorporates multi-link independent design with lower trailing arms, optimizing space beneath the floorpan for the battery while delivering precise control for high-performance driving in models produced through the 2020s. Aftermarket tuning further extends trailing-arm use in off-road vehicles like the , where upgraded adjustable trailing arm kits replace stock components to enhance articulation by up to 20-30% during extreme traversal, reducing bind and improving consistency. Semi-trailing arm variants were used in early generations of sports cars, such as the (1963–1998), for balanced dynamics.

Other Uses

In motorcycles, particularly dirt bikes, the rear suspension commonly employs a design, which functions as a trailing-arm system to enhance compliance. The pivots at the frame's lower rear section and extends backward to support the rear , allowing it to move vertically while maintaining alignment during rough off-road conditions. This configuration provides better absorption of impacts from uneven surfaces, improving rider control and stability in motocross applications, as seen in models like the Yamaha YZ series, where the integrates with a rear shock for adjustable . Off-road vehicles such as all-terrain vehicles (ATVs) utilize independent to achieve greater wheel travel over rough terrain. Aftermarket upgrades, such as trailing-arm conversions for the Ranger, replace traditional A-arm setups with elongated single trailing arms that pivot directly from the , enabling each rear wheel to articulate independently for enhanced ground contact and reduced body roll. This design increases suspension travel—often up to several inches more than configurations—while providing superior stability and comfort during low-speed navigation or high-impact jumps. Trailing-link landing gear appears in various small , where it serves as a suspension mechanism for during landings on uneven runways. The design features an L-shaped arm with a forward pivot point connected to an , which compresses air and oil to dampen vertical impacts and allow the to trail backward slightly upon . This geometry dissipates energy more smoothly than rigid or spring-based systems, reducing vibrations and structural stress; examples include the , which benefits from its forgiving performance on grass or gravel strips. Early rear suspensions incorporated trailing-link mechanisms to optimize pivot efficiency in full-suspension frames. The 1985 MCR Descender, one of the first such bikes, used a trailing-link setup with a central pivot and large air shock, delivering about 6 inches of to absorb bumps while minimizing energy loss during pedaling. This approach allowed the rear to follow terrain variations closely, enhancing traction and control on rough descents without excessive chain tension or bob.

Performance Characteristics

Advantages

Trailing-arm suspension offers significant advantages in design and cost-effectiveness compared to more complex systems like multi-link or double-wishbone setups. With fewer components—typically a single per along with basic bushings and springs—it requires less material and assembly time during , leading to lower production expenses. This simplicity also translates to reduced needs, as there are fewer joints and linkages prone to or misalignment, making it a practical choice for mass-produced vehicles. The compact of the trailing-arm configuration enhances , occupying minimal lateral and allowing for greater interior volume, such as expanded rear seating or cargo areas. This benefit is particularly pronounced in rear-engine layouts, where the integrates seamlessly without encroaching on components, optimizing overall . In terms of , the trailing-arm's orientation provides inherent longitudinal compliance, enabling the suspension to flex and absorb fore-aft forces from acceleration and braking. This natural characteristic helps mitigate wheel hop by maintaining consistent contact with the road, contributing to improved straight-line stability and traction, especially in high-torque applications like . Additionally, the system's lighter construction—due to reduced part count and often lower unsprung mass—yields weight savings over alternatives like double-wishbone suspensions, which can enhance and overall vehicle responsiveness in economy-oriented designs.

Disadvantages

Trailing-arm suspensions suffer from limited camber control owing to their inherently fixed geometry, which causes the wheels to remain vertical during pure vertical movements but develop undesirable positive camber on the outside wheel during body roll in corners. This camber gain reduces the tire's with the road, compromising cornering grip and stability. In semi-trailing arm variants, such camber variations can amount to approximately 0.8 degrees over the suspension travel range. The geometric constraints imposed by the arm's angle further restrict precise camber tuning under dynamic loads. These systems are also prone to bump steer susceptibility, as vertical wheel motions induce unintended toe changes without supplementary control links to mitigate them. In semi-trailing arm designs, the arm's swing during bump or rebound can produce small toe-in variations, leading to unpredictable handling inputs that affect straight-line stability and cornering precision. Additionally, trailing-arm setups often exhibit higher levels of (NVH), particularly in stiffer configurations, as they transmit road imperfections more readily than more compliant multi-link alternatives. Rubber bushings in these systems, while providing some isolation, can still propagate vibrations and road noise into the , degrading overall ride quality. In high-performance applications, trailing-arm suspensions have become obsolete since the early 2000s, supplanted by multi-link systems that offer greater adjustability and kinematic refinement for demanding handling requirements in modern sports cars.

References

  1. https://www.ijert.org/research/design-of-trailing-arm-suspension-IJERTV3IS060127.pdf
  2. https://www.cedengineering.com/userfiles/Automotive%20Suspension%20Systems.pdf
  3. https://www.autozine.org/technical_school/suspension/tech_suspension21.htm
  4. https://scholar.uc.edu/downloads/37720d96w?locale=en
  5. https://2021.help.altair.com/2021/hwdesktop/mv/topics/motionview/rear_trailing_arm_r.htm
  6. https://www.sciencedirect.com/topics/engineering/suspension-arm
  7. https://www.sciencedirect.com/topics/engineering/rear-suspension
  8. https://www.researchgate.net/publication/351992694_Design_Analysis_and_Optimization_of_Trailing_Arm_with_Two_Link_Suspension_System
  9. https://www.sciencedirect.com/topics/engineering/suspension-geometry
  10. https://www.hotcars.com/semi-trailing-arm-suspension-the-pros-and-cons/
  11. https://www.aopa.org/news-and-media/all-news/2019/june/flight-training-magazine/how-it-works-landing-gear
  12. https://www.audi-mediacenter.com/en/press-releases/history-of-the-four-rings-4093
  13. https://www.curbsideclassic.com/curbside-classics-european/cohort-classic-1961-bmw-600-the-four-passenger-isetta-stretch/
  14. http://www.classicandsportscar.com/features/bmw-1500-different-klasse
  15. https://www.heritagepartscentre.com/us/blog/vw-golf-mk1-history-us.html
  16. https://www.delphiautoparts.com/en-gb/mom/how-to/article/what-is-suspension
  17. https://www.kfz-tech.de/Engl/Biblio/Fahrwerk/FahrwerkG02.htm
  18. https://www.irjet.net/archives/V11/i4/IRJET-V11I4164.pdf
  19. https://www.fordmuscle.com/tech-stories/brakes-suspension/a-guide-to-buying-aftermarket-rear-control-arms/
  20. http://wanderlodgegurus.com/database/Theory/Suspension%20Geometry%20%26%20Computation%20Dixon.pdf
  21. https://engineering.purdue.edu/pup/wp-content/uploads/2013/12/Lumkes_CIGR_2012_BUV_belts.pdf
  22. https://www.carparts.com/blog/bad-trailing-arm-symptoms/
  23. https://www.sciencedirect.com/topics/engineering/suspension-linkage
  24. http://e30sport.net/tech_articles/susp-tech/rear_curves/page-2.htm
  25. https://www.bluestradatours.com/car-suspension-kinematics-schemes/
  26. https://www.hagerty.com/media/market-trends/hagerty-insider/market-spotlight/bmws-first-3-series-e21-is-quietly-climbing/
  27. https://bringatrailer.com/2019/01/31/middle-child-syndrome-the-underrated-bmw-e21/
  28. https://newsroom.porsche.com/en/innovation/engineering/porsche-928-weissach-axle-transaxle-chassis-technology-front-engine-15493.html
  29. https://prestigeandperformancecar.com/porsche/porsche-weissach-axle-tech-guide/
  30. https://image.mamotorworksmedia.com/production/website/articlefiles/TAFiles/VW_Suspension_Types.pdf
  31. https://global.honda/en/about/history-digest/75years-history/chapter3/section2_2/page2.html
  32. https://www.theautopian.com/why-the-current-ford-f-150-is-actually-three-trucks-in-one-suspension-secrets/
  33. https://service.tesla.com/docs/Model3/ServiceManual/en-us/GUID-1E92D102-7343-4034-ADF8-0280F94751FE.html
  34. https://core4x4.com/
  35. https://www.cycleworld.com/story/blogs/ask-kevin/motorcycle-swingarms-explained/
  36. https://www.digrigpowersports.com/blog/polaris-ranger-trailing-arm-conversion/
  37. https://www.boldmethod.com/learn-to-fly/systems/trailing-link-landing-gear-smoother-landing/
  38. https://www.theproscloset.com/blogs/news/five-vintage-full-suspension-bikes
  39. https://www.gswautoparts.com/the-how-why-of-trailing-arm-suspension/
  40. https://www.sciencedirect.com/science/article/pii/B9780128126936000079
  41. https://www.sciencedirect.com/science/article/pii/B9780750651318500117
Add your contribution
Related Hubs
User Avatar
No comments yet.