Hubbry Logo
Brace (tool)Brace (tool)Main
Open search
Brace (tool)
Community hub
Brace (tool)
logo
8 pages, 0 posts
0 subscribers
Be the first to start a discussion here.
Be the first to start a discussion here.
Brace (tool)
Brace (tool)
Brace (tool)
View on Wikipedia
from Wikipedia
A brace with various bits

A brace is a hand tool used with a bit (drill bit or auger) to drill holes, usually in wood. Pressure is applied to the top while the handle is rotated. If the bit's lead and cutting spurs are both in good working order, the user should not have to apply any pressure other than for balance: the lead will pull the bit through the wood. The earliest carpenter's braces equipped with a U-shaped grip, that is with a compound crank, appeared between 1420 and 1430 in Flanders.[1]

Types

[edit]

Bits used to come in a variety of types but the more commonly used Ridgeway and Irwin-pattern bits also rely on a tip called a snail, which is a tapered threaded screw that pulls the bit forward.

Handle

[edit]

The U-shaped handle is a crank. It gives the brace much greater torque than other kinds of hand-powered drills. A brace and bit can be used to drill wider and deeper holes than can a geared hand-powered drill. The cost of the greater torque is lower rotational speed; it is easy for a geared hand drill to achieve a rotational speed of several hundred revolutions per minute, while it would require considerable effort to achieve even 100 rpm with a brace.

Spindle

[edit]

The front of the brace consists of a chuck spindle with V-shaped brackets or clamps inside. Turning the spindle of the chuck in a clockwise direction tightens the drill bit in the chuck; turning counterclockwise loosens the bit for removal.

A carpenter using a brace


The U-shaped crank has a wooden spindle on it and—along with the top spindle—is allowed to freely turn under the hands without stressing the hands, thus preventing blisters.

Gear release

[edit]

In most modern braces, immediately behind the chuck is a three position gear release that allows ratcheting of the handle when in tight spots. Turning the gear release from the center position allows ratcheting the brace in the required direction. Turning the gear release fully clockwise lets it remove wood in a clockwise direction with the ratchet action going counterclockwise. Placing the gear release fully counterclockwise allows turning the brace and bit in a counterclockwise direction, usually to remove the drill bit from the hole. The center position of the gear release prohibits the ratcheting effect.


Alternative names

[edit]

The brace has other names. Bit brace is the most often used name, but carpenter's brace, ratchet brace (if a ratchet mechanism is incorporated into the design), and swing brace are also commonly used.

See also

[edit]
  • Hand drills for some related tools, including the type sometimes known as a wheel brace.

Citations

[edit]
  1. ^ White 1962, p. 112

General and cited references

[edit]
Revisions and contributorsEdit on WikipediaRead on Wikipedia

Brace (tool)

View on Grokipedia
from Grokipedia
A brace, also known as a bit brace or bitstock, is a hand-operated woodworking tool designed for boring holes in wood by manually rotating a drill bit or auger. It functions as a crank mechanism that allows the user to apply rotational force efficiently, making it essential for tasks such as preparing mortise-and-tenon joints, inserting screws, or drilling for dowels. The tool's versatility extends beyond boring, as it can also hold accessories like screwdrivers or dowel pointers for additional woodworking operations. The brace evolved from earlier boring methods, with its crank principle traceable to ancient Chinese mechanisms, though the modern form emerged in during the 1400s. By the , wooden braces were common across and the British Isles, often featuring simple lever-wedge systems to secure bits. The Sheffield-style brace, standardized around 1750 with a wooden and metal , later saw improvements in durability with reinforcements by the early , while 19th-century innovations in the United States introduced metallic constructions and patented chucks for improved bit retention. Mass production of steel braces, including ratchet-equipped models, proliferated after the , peaking with refinements like ball bearings and nickel plating by 1900. Structurally, a typical brace comprises a head (or ) gripped by the palm and fingers for control, a central shank that transmits , and a at the base to clamp the bit's tang via adjustable jaws. The crank arm, attached to the shank, enables the user to turn the tool with one hand while stabilizing the head with the other, producing a "sweep" that determines the tool's reach—commonly ranging from 6 to 10 inches. Ratchet braces incorporate a pawl and gear system for unidirectional , allowing efficient in confined spaces near edges or corners without full circular swings. Although largely supplanted by power drills in contemporary , the brace remains valued for its precision in fine craftsmanship, restoration work, and situations requiring controlled to avoid splintering delicate woods. Its enduring design underscores the transition from manual to mechanized tools in history.

Overview

Definition

A brace is a hand-held boring tool used primarily to drill holes in , consisting of a U- or bow-shaped frame, a crank handle for rotation, and a to secure drill bits or augers. It operates by applying downward on the frame's head while manually turning the crank to rotate the bit, enabling controlled penetration into the material. The tool's design emphasizes high generation at low rotational speeds through the mechanical advantage of the crank, making it ideal for boring larger-diameter holes that exceed the capacity of standard hand drills. This manual cranking method allows users to apply substantial force without electrical power, typically achieving speeds sufficient for efficient cutting in but prioritizing power over rapid rotation. Bit braces first emerged in during the 15th century as an advancement in . Also known as a bit brace, carpenter's brace, or swing brace, it differs from power drills and geared hand drills by relying entirely on human effort for rotation without electric motors or internal gear mechanisms to amplify speed. This distinction positions the brace as a low-speed, high-torque alternative suited for precision work in confined spaces or off-grid environments.

Basic Operation

To operate a brace, first insert the bit into the and secure it by tightening . Position the bit's tip on the workpiece, using an awl to mark the center point for accuracy, then apply steady downward pressure on the pommel with the non-dominant hand while cranking the with the dominant hand to rotate and advance the bit into the material. Torque is generated by applying rotational to the U-shaped , leveraging the brace's frame to pull the bit forward via its lead screw mechanism, allowing the user to bore deeper holes with controlled effort. The low rotational speed, typically achieved manually, enables precise depth control by monitoring and counting handle turns, making it suitable for drilling holes ranging from 1/4 to 2 inches in diameter, often with auger bits for wood. For safety, maintain straight alignment throughout the process—using aids like squares or reflective surfaces if needed—to prevent bit binding, breakage, or workpiece damage; avoid excessive pressure, especially as the bit nears breakthrough, to minimize tear-out or splitting.

History

Early Origins

The earliest precursors to the modern brace tool emerged in prehistoric practices, where simple boring mechanisms were developed to create holes in wood, , and other materials. These rudimentary devices, such as pointed bone awls or flaked stone piercers rotated or pushed by hand, date back thousands of years and represent the foundational techniques for manual . Flaked stone tools further illustrate early experimentation with rotation-based boring during the . The crank principle underlying later braces can be traced to ancient Chinese mechanisms, predating European developments. In ancient civilizations, these concepts evolved into more sophisticated bow-driven and T-handled boring tools, particularly in Egyptian and Roman around 2000 BCE. Egyptian carpenters employed bow drills—consisting of a wooden shaft with a flint or point, rotated via a bowstring for efficient hole-making—as evidenced by carvings from the pre-dynastic and periods (c. 3500–2500 BCE). These tools allowed for precise boring in scarce hardwoods like , essential for furniture and architectural elements. Roman artisans advanced this with iron pod augers and bits fitted to T-handles, enabling deeper and more controlled penetration in timber, as archaeological finds from military camps (c. 700 BCE–75 CE) demonstrate their widespread use in and . The medieval period marked the transition to brace-like tools, with the first recognizable U-shaped metal braces appearing in during the late 14th and early 15th centuries, initially for demanding tasks in and . Illuminated manuscripts and contemporary depictions, such as those showing using a brace for boring, confirm their adoption around – in regions like and the , where they facilitated in large-scale wooden structures. These early braces featured a cranked for rotational force, building on Roman auger designs but adapted for greater leverage in guild-based workshops. Constructed primarily from wood for the frame and early iron for the chuck and spindle, these braces used bow or straight handles to generate torque without advanced mechanisms. By the mid-15th century, their integration into European carpentry guilds standardized basic forms, spreading across trade networks and influencing tool evolution toward more efficient ratcheting variants in subsequent eras.

Modern Evolution

The brace underwent significant advancements during the 18th and 19th centuries, transitioning from primarily wooden constructions to more durable designs suited for industrial use. In the late 18th and early 19th centuries, English manufacturers in Sheffield began standardizing wooden braces with brass reinforcements for added strength, while mechanisms like lever-wedges evolved into pressure-spring buttons for easier bit retention. By the early 19th century, the introduction of ratchet mechanisms addressed the challenge of drilling in confined spaces, with the first American patent for such a device granted to Henry Porter in 1857, enabling partial rotations without full swings. This innovation, along with a shift toward all-metal construction—often featuring steel frames and nickel-plating for corrosion resistance while retaining beechwood or rosewood handles for grip and balance—enhanced the tool's durability and precision in woodworking tasks. In the , American manufacturers played a pivotal role in commercializing and refining the brace, leading to widespread adoption. Key producers included , which by 1915 offered 135 variations in its catalog, ranging from standard ratcheting models to specialized angular braces, reflecting the tool's versatility in and . Stanley Tools also contributed significantly, helping standardize the "American Pattern" brace with a universal chuck design that accommodated various bit shanks, such as augers and ship augers, promoting interchangeability across trade applications. These developments, driven by techniques post-Civil War, solidified the brace as an essential in workshops. The marked the peak popularity of the brace followed by its gradual decline amid the rise of powered alternatives. Widespread use persisted through the early decades, particularly in and fine woodworking, until the 1950s when electric power drills offered greater speed and convenience, reducing demand for hand braces from over 100 catalog models in the to just 13 by at Millers Falls. Post-World War II innovations, such as push-button quick-release chucks, briefly modernized the tool by simplifying bit changes, but these enhancements could not compete with battery-powered options. By mid-century, production shifted toward specialized or export markets. In the , the brace occupies a niche role among hand-tool enthusiasts and restoration specialists, with limited new production focused on high-quality reproductions. Companies like Garrett Wade offer faithful recreations of classic ratcheting designs, emphasizing ergonomic handles and universal chucks for traditional techniques where power tools are impractical, such as in tight spaces or off-grid settings. This resurgence underscores the brace's enduring value in precision, low-impact , appealing to a valuing artisanal methods over mass .

Design and Components

Frame and Handle

The frame of a brace tool consists of a curved U- or bow-shaped metal body, typically constructed from , that connects the assembly to the spindle while providing structural leverage for applying rotational force during operations. This design ensures stability and transmits efficiently from the user's input to the bit, with the frame's arc allowing for a sweeping motion that enhances control in tasks. Handle configurations include a fixed pommel or crank-style head at the rear for delivering downward pressure to advance the bit, paired with a rotating crossbar or D-shaped grip at the front for manual rotation. These handles often feature ergonomic wooden construction, such as beechwood, to offer a secure, non-slip hold and reduce fatigue during prolonged use. The overall sweep length of the frame—measuring the of the rotational path—typically ranges from 6 to 12 inches, with 10 inches being the most common, striking a balance between maneuverability and power delivery. The frame's geometry leverages the wheel-and-axle principle, where the handle acts as the wheel and the spindle as the , generating to multiply applied force and facilitate delivery into dense materials like hardwoods. Longer sweeps, such as 12 inches, amplify this for aggressive boring in heavy-duty applications, whereas shorter 6-inch variants prioritize precision in confined or detailed work. Compact models thus suit fine craftsmanship, while extended frames support broader leverage needs without compromising the tool's core ergonomic profile.

Chuck and Spindle

The spindle serves as the central rotating shaft in a brace tool, connecting the frame to the and transmitting rotational force from the handle-driven crank to the attached bit for . This component is typically a hollow, cylindrical element with longitudinal slots to accommodate the 's jaws, allowing for radial movement while maintaining structural integrity during operation. To ensure smooth motion and minimize friction, many designs incorporate ball bearings or similar supports at the spindle's mounting points within the frame, enabling efficient transfer without binding. The chuck, located at the distal end of the spindle, is the bit-holding mechanism designed to securely grip various shank configurations. Common designs include the universal chuck or two-jaw type, featuring V-shaped clamps or jaws that conform to the square tang of the bit for a firm, non-slip hold. These jaws, often spring-loaded for quick release, are adjusted by rotating a shell or using a key in a clockwise direction to tighten, with serrated or grooved faces enhancing grip on tapered shanks. In four-jaw variants, the rectangular base aligns with square shanks up to 8 mm, centering the bit precisely to prevent wobbling during use. Bit engagement occurs through the chuck's jaws clamping onto the bit's tapered square tang, providing compatibility with self-feeding mechanisms on bits such as the Irwin pattern, where the lead screw at the bit tip draws it into the material as rotation progresses. This secure fit ensures the bit remains aligned and stable, transmitting full rotational force without slippage, even under high torque. Maintenance of the chuck and spindle involves regular lubrication to reduce friction and prevent wear. Oil or grease should be applied to the spindle bearings, jaw threads, and tapered slopes of the clamps, as these areas experience rubbing during adjustment and rotation. Common failures arise from clamp wear, leading to loose bit retention; cleaning the jaw housing and re-greasing can extend component life, but worn parts may require replacement to maintain precision.

Ratchet Mechanism

The ratchet mechanism in a brace tool enables directional control for in confined spaces, where a full 360-degree of the is impractical, such as near walls or in corners. It functions by allowing one-way of the spindle through engagement of geared teeth, permitting oscillatory cranking motions that advance the bit incrementally while preventing back- in the engaged direction. This optional gearing supports three primary modes—clockwise , counterclockwise , and a locked or free-spinning mode for continuous full-circle operation—selected via a three-position mechanism, enhancing efficiency in tight workspaces. The design typically incorporates an internal toothed gear ring, often termed the ratchet wheel, mounted on the shank connected to the chuck and spindle, with a pawl system that engages the teeth to enforce unidirectional motion. In classic configurations, such as those patented in the late 19th century, a compound pawl or lever plate is spring-loaded against the wheel, featuring multiple engagement surfaces: inclined faces for ratcheting in either direction and a straight face for locking into grooves to allow bidirectional full rotation without ratcheting. This pawl is housed within a ratchet box or sleeve integrated into the brace's frame and handle assembly, secured by pins, springs, and sometimes a threaded nut for adjustment to minimize play. The mechanism's teeth and pawls produce a characteristic clicking sound as the pawl slides over the teeth during the return stroke in ratcheting mode, providing auditory feedback on engagement. Operation involves adjusting a selector or knob on the ratchet housing to the desired mode before applying downward pressure on the brace's head while oscillating the bow handle. In modes, forward motion drives the bit via pawl-tooth , while the return stroke slips the pawl over the teeth with a click; the locked mode disengages the for standard full-sweep use. Regular is essential, with a few drops of oil applied to the pawls, their pivot points, and between the ratchet and housing to ensure smooth and prevent binding. While effective, the ratchet mechanism adds noticeable weight to the brace compared to non-ratcheting models, potentially increasing user fatigue during prolonged use, and is prone to jamming or excessive wear if not periodically lubricated or maintained, as debris or dried residues can impede pawl movement.

Types of Braces

Standard Ratchet Brace

The standard ratchet brace is the most prevalent variant of the carpenter's brace, characterized by its all-metal construction, typically featuring a 10-inch body made of nickel-plated for durability and resistance. It includes a ratcheting mechanism that allows for continuous rotation in confined spaces, a universal capable of gripping various bit shanks such as round (up to 1/2 inch), square, or taper types, and ergonomic wooden handles—often or teakwood—for comfortable operation. The tool's sweep, or crank radius, commonly measures 8 to 10 inches per full turn, enabling efficient boring without excessive arm movement. This design provides significant advantages in general , offering versatility for tasks like pilot holes or enlarging openings, while delivering high suitable for creating holes over 1 inch in in hardwoods, where power drills may struggle without slippage. The ratchet feature enhances control in tight corners, and the ball-bearing head reduces for smoother, less fatiguing use compared to non-ratcheting models. Prominent examples from the early include the Millers Falls No. 71, available in 8-, 10-, and 12-inch sweeps with a teakwood head and handle, ball-bearing construction, and plating for a premium finish. Equivalent models, such as the Stanley No. 923, shared similar specifications with a concealed ratchet, mirror-polished body, and handles, produced from 1905 onward to meet demands for reliable hand-powered . Sizing of the standard ratchet brace is primarily determined by the sweep, which directly influences torque output: larger sweeps (e.g., 10-12 inches) generate greater for heavy-duty boring in dense materials, while smaller ones (8 inches) prioritize maneuverability and precision in detailed work. This scalability made the tool a staple in workshops, balancing power and accessibility without requiring .

Socket and Specialized Braces

The socket brace features a specialized designed to accommodate hexagonal shank bits or extensions, allowing for efficient bit changes and compatibility with non-standard tooling. This design is particularly advantageous for overhead or awkwardly angled tasks, where the brace's crank can be positioned horizontally for better control and reduced fatigue. The slide-handle brace incorporates an adjustable steadying handle, often referred to as a pommel, that can be positioned along the frame to vary and leverage. This adaptability makes it ideal for fine tasks requiring precise control, such as detailed or smaller diameter holes, by allowing users to optimize the handle's placement for comfort and power application. Early examples, like those from Goodell-Pratt, offered up to eight handle positions to suit different operational needs. Universal joint braces integrate a flexible , such as a linkage, to enable at non-perpendicular angles or around corners without compromising alignment. Patented designs like Charles Amidon's (U.S. Patent No. 298,542) allowed for both and geared mechanisms, facilitating access in tight spaces common to or frame construction. These braces maintain rotational efficiency while accommodating up to 90-degree offsets, proving invaluable for intricate layouts. Modern adaptations of these specialized braces include quick-release mechanisms, such as hex bit holders with set screws for rapid bit swaps, catering to hobbyists seeking efficiency with contemporary hex-shank tooling. Additionally, reversible ratchet systems in updated models accommodate left-handed users by allowing or counterclockwise operation without disassembly, extending in diverse environments.

Compatible Bits

Auger Bits

Auger bits are the primary boring tools designed for use with hand braces, featuring a that spirals around a central lead , known as the snail point, which self-feeds into the wood by drawing the bit forward as it rotates. The lead also ensures precise centering and prevents the bit from wandering during initial entry. At the rear, a square tang secures into the brace's , providing a firm grip for manual rotation. These bits are typically constructed from high-carbon steel for durability and edge retention, with common diameters ranging from 1/4 inch to 1-1/2 inches to accommodate various needs. Two prominent patterns dominate traditional auger bit designs: the Jennings pattern, with a single open-center flute for efficient chip removal in various woods, and the Irwin pattern, characterized by a single solid-center flute for deep, aggressive cutting and added rigidity in dense woods. Both patterns include a single at the tip to score the hole's perimeter and twin cutters that shear the wood fibers cleanly. Sharpening auger bits requires attention to the spur, cutters, and lead screw to maintain efficiency. The inside edges of the spur and the top faces of the cutters are filed flat using a mill file, ensuring they remain perpendicular to the flute for even scoring and shearing. Nicks on the lead screw can be cleaned by running it through a pre-drilled hole lubricated with polishing compound, preserving its self-feeding action without altering its pitch. Proper sharpening extends the bit's life and prevents binding, as dull edges can cause the lead screw to overheat or deflect. In performance, auger bits excel at producing straight, clean holes in , leveraging the lead screw's guidance and the flute's chip clearance to achieve depths up to 18 inches without deviation. This design minimizes tear-out along the hole walls, yielding smooth bores ideal for or structural applications, though they perform best at low rotational speeds to avoid overheating the . Compared to twist drills, augers remove material more efficiently in deep operations, but their manual compatibility with braces limits speed in favor of control and precision.

Spoon and Other Bits

Spoon bits are characterized by their curved, gouge-like cutting edge, which enables rapid boring of relatively rough holes primarily in softwoods and green wood. These bits excel in producing clean entry and exit holes, even at steep angles, making them ideal for tasks like drilling angled mortises in chairmaking, such as for Windsor chair spindles. Available in sizes ranging from 5/16 inch to 1 inch in diameter, spoon bits typically feature a simple, elongated spoon-shaped profile without a lead screw, allowing for controlled depth without breakthrough risk. Beyond spoon bits, braces accommodate various specialized bits for diverse woodworking needs. Countersink bits create conical recesses to seat screw heads flush with or below the wood surface, facilitating concealed fasteners in and . Gimlet bits, with their self-tapping screw-like point, are designed for quick pilot holes in preparation for nails or screws, particularly effective in softwoods for small-diameter work up to 3/8 inch. Reamers enlarge or taper existing holes to precise fits, often used in chairmaking or furniture assembly to match tenons snugly. Tenon cutters, meanwhile, shape the ends of stock into tapered or straight tenons for mortise-and-tenon , producing uniform cylindrical or polygonal forms essential for traditional frame construction. Most of these bits, including , gimlet, and varieties, are forged from high-carbon steel to maintain sharpness during hand-powered operation. Some designs incorporate extensions—threaded rods or adapters—to reach greater depths in confined spaces, extending effective boring length beyond the brace's natural throw. While versatile in softwoods, bits and similar non-helical types are less efficient in hardwoods, where they may bind or tear out more readily compared to auger bits suited for deeper, straighter work.

Applications

Traditional Woodworking

In traditional woodworking, the brace served as an essential tool for joinery, particularly in drilling precise holes for mortise-and-tenon joints and dowels used in furniture and cabinetry construction during the 18th and 19th centuries. Its crank mechanism allowed woodworkers to apply controlled pressure and torque, enabling accurate depth control to prevent over-boring and ensure tight fits in assemblies like table legs or frame components. This precision was critical in pre-industrial workshops, where the brace facilitated the creation of interlocking joints without modern machinery. The brace excelled in specialized applications such as chair making and , where it was employed to bore angled holes using spoon bits, which cut cleanly even at steep angles for tenon insertions in turned legs or structural fastenings. In boat construction, back to medieval practices and continuing through the , the tool's high capability handled dense hardwoods like , producing crisp chips and smooth holes for fastenings in hull framing or planking. These attributes made it indispensable for crafts requiring durability against twisting forces in curved or irregular timber. Within period techniques, the brace was integral to guild-based , often used in tandem with planes and saws to shape and assemble pieces in a sequential . Notable examples include the 18th-century Dominy craftsmen of , who relied on braces—known as bitstocks—to drill holes for furniture and , as evidenced by their preserved tool collection at the Museum. This hands-on method supported efficient production in small-scale shops, complementing other hand tools for comprehensive craftsmanship.

Modern and Specialized Uses

In contemporary hand-tool , the brace remains valued for its precision in green woodworking and restoration projects, where power tools' heat could warp or damage sensitive timber. For instance, spoon bits paired with a brace excel at boring clean holes in freshly cut greenwood without generating excessive friction or heat, preserving the wood's natural moisture content during tasks like chair leg tenoning. This method is particularly prominent in chairmaking workshops, where participants use braces to drill angled mortises in unseasoned wood, achieving greater control over hole depth and alignment compared to powered alternatives. Beyond traditional , the brace finds application in specialized fields requiring finesse in confined or delicate settings. In electrical installations, such as those by historical telephone linemen, compact ratcheting braces enabled precise hole boring through walls and framing in tight spaces without the bulk of power tools. Key advantages of the brace in modern contexts include its cordless and battery-free design, ideal for remote or off-grid sites like outdoor restorations or field expeditions, where power access is limited. Additionally, the tool provides superior ergonomic control for angled or stopped holes, enabling woodworkers to maintain consistent pressure and direction for precise outcomes in intricate . Among antique tool enthusiasts, vintage braces—particularly those from makers like Stanley or Millers Falls—are highly collectible for their craftsmanship and historical significance, often fetching premiums at auctions due to well-preserved ratchet mechanisms and exotic wood handles. For hobbyists seeking functional alternatives, modern reproductions and new-production braces, compatible with legacy bits, are available from specialty suppliers, bridging traditional design with contemporary use in home workshops.

References

  1. https://www.gutenberg.org/files/20846/20846-h/20846-h.htm
  2. https://www.woodmagazine.com/woodworking-tools/hand/bit-braces-and-hand-drills
  3. https://www.gutenberg.org/files/27238/27238-h/27238-h.htm
  4. https://www.popularwoodworking.com/tools/arts-mysteries-boring-in-the-18th-century/
  5. https://www.finewoodworking.com/1988/08/01/the-brace-and-bit
  6. https://etc.usf.edu/clipart/galleries/1503-drills-and-drill-bits
  7. https://www.asec.purdue.edu/tractor/Notes/NotesS11-2%20-%20Hand%20Tools.pdf
  8. https://www.popularwoodworking.com/techniques/the-essential-brace-bit/
  9. https://craftisian.com/entries/1677-part-8-tips-and-tricks-on-using-a-hand-brace
  10. https://www.wagnermeters.com/moisture-meters/wood-info/history-of-woodworking/
  11. https://repository.si.edu/bitstream/handle/10088/30446/1966_Bulletin_177-232.pdf?sequence=1&isAllowed=y
  12. https://solar.lowtechmagazine.com/2010/12/hand-powered-drilling-tools-and-machines/
  13. https://oldtoolheaven.com/millers-falls/brace/brace.htm
  14. https://mathesontools.weebly.com/blog/braces-part-i
  15. https://garrettwade.com/woodworking/drilling/hand-drills-braces/
  16. https://wiki.dtonline.org/index.php/Carpenter%27s_Brace
  17. https://commonwoodworking.com/swing-brace-guide/
  18. https://woodandshop.com/woodworking-hand-tool-buying-guide-hand-drills-braces-bits/
  19. https://www.tooltique.co.uk/shop/vintage-skinner-carpenters-brace-beechwood-handles-10-swing-good-condition/
  20. https://paulsellers.com/2014/12/questions-answered-on-brace-and-bits/
  21. https://patents.google.com/patent/US609478A/en
  22. https://oldtoolheaven.com/millers-falls/brace/FeaturedBraces.htm
  23. https://www.fine-tools.com/Jaw-Brace-with-Four-Jaw-Chuck-and-plastic-Knob-and-Grip/301185
  24. https://toolsforworkingwood.com/store/blog/1178
  25. https://paulsellers.com/2019/06/bits-and-braces/
  26. https://patents.google.com/patent/US438338A/en
  27. https://www.lumberjocks.com/threads/source-for-ratchet-pawl-for-stanley-brace.49196/
  28. https://ncwoodworker.net/forums/index.php?threads/new-life-to-an-old-tool-re-furbishing-a-bit-brace.54345/
  29. https://www.ukworkshop.co.uk/threads/brace-non-ratchet.96519/
  30. https://toolsforworkingwood.com/store/blog/1176
  31. https://ia800404.us.archive.org/13/items/StanleyToolsCatalogNo.34/Stanley0001.pdf
  32. https://ia601204.us.archive.org/27/items/illustratedcatal00john_2/illustratedcatal00john_2.pdf
  33. https://www.leevalley.com/en-us/shop/tools/hand-tools/drills/113164-three-jaw-chuck-brace
  34. https://www.classicboat.co.uk/practical-advice/traditional-tools/the-brace-and-the-bit/
  35. https://oldtoolheaven.com/related/goodell-pratt-braces.htm
  36. https://oldtoolheaven.com/millers-falls/galleries/Amidon/Amidongallery.htm
  37. https://www.fine-tools.com/Brace-Accessory-1-4-inch-6.35-mm-hex-internal-Bit-Holder-with-Screw-and-conical-square-Shaft/300222
  38. https://garrettwade.com/product/versatile-9-inch-socket-brace
  39. https://craftisian.com/entries/1676-part-7-sharpening-an-auger-bit
  40. https://www.icscuttingtools.com/pdfs/auger-bit-sharpening.pdf
  41. https://www.tongyutools.com/wood-drill-bits/Wood_Auger_Drill_Bits/Hand_Use_Aug/2021/0513/429.html
  42. https://www.leevalley.com/en-us/shop/tools/power-tool-accessories/drill-bits/45003-single-flute-auger-bits
  43. https://sawmillcreek.org/threads/jenning-vs-irwin.240981/
  44. https://chgans.design.blog/2020/06/06/irwin-auger-bits/
  45. https://www.popularwoodworking.com/tools/tool-test-jennings-pattern-auger-bits-for-braces-2/
  46. https://journeymansjournel.wordpress.com/2020/08/08/the-sharpening-of-bits/
  47. https://workshopcompanion.com/know-how/tools/sharpening/drill-bits.html
  48. https://sawmillcreek.org/threads/auger-bit-lead-screw.49558/
  49. https://www.youtube.com/watch?v=q7V0hG2ZX_I
  50. https://www.findbuytool.com/en-ca/blogs/university/spade-bit-vs-auger-bit-vs-forstner-which-one-is-better
  51. https://toolsriseon.com/auger-bit-vs-drill-bit/
  52. https://handtoolwoodworking.com/the-lore-of-the-spoon-bit/
  53. https://handtoolwoodworking.com/review-of-chairmaking-drill-bits/
  54. https://www.finewoodworking.com/1983/12/01/spoon-bits
  55. https://blog.lostartpress.com/2018/05/27/an-excellent-countersink/
  56. https://blog.vintagetoolpatch.com/2022/03/13/gimlet-bits.html
  57. https://www.renaissancewoodworker.com/gimlet-bits-anyone/
  58. https://handtoolwoodworking.com/tenon-cutters/
  59. https://www.amazon.com/Carbon-Wooden-Machined-Drills-Gimlet/dp/B0CWLL8CNG
  60. https://www.lumberjocks.com/threads/types-of-brace-bits.316970/
  61. https://dominycollections.winterthur.org/tools-of-the-trade/woodworking/bit/
  62. https://www.popularwoodworking.com/editors-blog/new-spoon-bits-from-gramercy-tools/
  63. https://www.classicrotaryphones.com/forum/index.php?topic=13626.0
  64. https://www.antiqbuyer.com/past-sale-archives/antique-tools/drill.htm
Add your contribution
Related Hubs
User Avatar
No comments yet.