.jpg)
Community hub
Recent from talks
Knowledge base stats:
Talk channels stats:
Members stats:
EMD F7
The EMD F7 is a model of 1,500-horsepower (1,100 kW) diesel-electric locomotive produced between February 1949 and December 1953 by the Electro-Motive Division of General Motors (EMD) and General Motors Diesel (GMD).
Although originally promoted by EMD as a freight-hauling unit, the F-series, including the F7 were also capable of passenger service, and used in hauling trains such as the Santa Fe Railway's high-speed flagship trains, the Super Chief, & El Capitan, and the Ontario Northland's Northlander.
The F7 was the fourth model in GM-EMD's successful line of F-unit locomotives, and by far the best-selling cab unit of all time. In fact, more F7s were built than all other F-units combined. The F7 succeeded the F3 model in GM-EMD's F-unit series, and was replaced in turn by the F9. Final assembly was at GM-EMD's La Grange, Illinois, plant or GMD's London, Ontario, facility. There was no F4, -5 or -6 model; "7" was chosen to match the contemporary twin-engine E7, and was also applied to the new GP7 road-switcher.
The F7 differed from the F3 primarily in internal equipment—mostly electrical—and some external features. Its continuous tractive effort rating was 20 percent higher, e.g. 40,000 lbf (180 kN) for an F7 with 65 mph (105 km/h) gearing, compared to 32,500 lbf (145 kN) for an F3 with the same gearing.
Many F7s remained in service for decades, as railroads found them economical to operate and maintain. However, the locomotive was not very popular with yard crews who operated them in switching service because they were difficult to mount and dismount, and it was also nearly impossible for the engineer to see hand signals from a ground crew without leaning way outside the window. As most of these engines were bought and operated before two-way radio became standard on most American railroads, this was a major point of contention. In later years, with the advent of the "road switchers" such as the EMD GP7, F-units were primarily used in "through freight" and "unit train" service where there was little or no switching to be done.
The F7's prime mover is a 16-cylinder 567B series diesel engine developing 1,500 hp (1.1 MW) at 800 rpm. The 567B is a mechanically aspirated two-stroke design in a 45-degree V engine configuration, with 567 cu in (9.29 L) displacement per cylinder, for a total of 9,072 cu in (148.66 L). A direct current generator that is mechanically coupled to the flywheel end of the engine powers four traction motors, with two motors mounted on each Blomberg B truck. EMD has built all of its major components since 1939.
There are no easily identifiable differences between late F3 production and early F7 production; the major differences were all internal electrical system changes. However, no F7 had the "chicken wire" grilles seen on most F3s, and no F3s had later F7 changes described below under Phases.
The F9 is distinguishable from the late F7 by having five, rather than four, carbody center louver groups covering the carbody filters. The additional one is placed ahead of the first porthole, where F7s have no openings. The F9's greater power output, of course, cannot be seen from the outside.
Hub AI
EMD F7 AI simulator
(@EMD F7_simulator)
EMD F7
The EMD F7 is a model of 1,500-horsepower (1,100 kW) diesel-electric locomotive produced between February 1949 and December 1953 by the Electro-Motive Division of General Motors (EMD) and General Motors Diesel (GMD).
Although originally promoted by EMD as a freight-hauling unit, the F-series, including the F7 were also capable of passenger service, and used in hauling trains such as the Santa Fe Railway's high-speed flagship trains, the Super Chief, & El Capitan, and the Ontario Northland's Northlander.
The F7 was the fourth model in GM-EMD's successful line of F-unit locomotives, and by far the best-selling cab unit of all time. In fact, more F7s were built than all other F-units combined. The F7 succeeded the F3 model in GM-EMD's F-unit series, and was replaced in turn by the F9. Final assembly was at GM-EMD's La Grange, Illinois, plant or GMD's London, Ontario, facility. There was no F4, -5 or -6 model; "7" was chosen to match the contemporary twin-engine E7, and was also applied to the new GP7 road-switcher.
The F7 differed from the F3 primarily in internal equipment—mostly electrical—and some external features. Its continuous tractive effort rating was 20 percent higher, e.g. 40,000 lbf (180 kN) for an F7 with 65 mph (105 km/h) gearing, compared to 32,500 lbf (145 kN) for an F3 with the same gearing.
Many F7s remained in service for decades, as railroads found them economical to operate and maintain. However, the locomotive was not very popular with yard crews who operated them in switching service because they were difficult to mount and dismount, and it was also nearly impossible for the engineer to see hand signals from a ground crew without leaning way outside the window. As most of these engines were bought and operated before two-way radio became standard on most American railroads, this was a major point of contention. In later years, with the advent of the "road switchers" such as the EMD GP7, F-units were primarily used in "through freight" and "unit train" service where there was little or no switching to be done.
The F7's prime mover is a 16-cylinder 567B series diesel engine developing 1,500 hp (1.1 MW) at 800 rpm. The 567B is a mechanically aspirated two-stroke design in a 45-degree V engine configuration, with 567 cu in (9.29 L) displacement per cylinder, for a total of 9,072 cu in (148.66 L). A direct current generator that is mechanically coupled to the flywheel end of the engine powers four traction motors, with two motors mounted on each Blomberg B truck. EMD has built all of its major components since 1939.
There are no easily identifiable differences between late F3 production and early F7 production; the major differences were all internal electrical system changes. However, no F7 had the "chicken wire" grilles seen on most F3s, and no F3s had later F7 changes described below under Phases.
The F9 is distinguishable from the late F7 by having five, rather than four, carbody center louver groups covering the carbody filters. The additional one is placed ahead of the first porthole, where F7s have no openings. The F9's greater power output, of course, cannot be seen from the outside.