Hubbry Logo
search
logo
SI derived unit avatar
SI derived unit
SI derived unit
current hub
S

SI derived unit

logo
Community Hub0 Subscribers
Read side by side
SI derived unit
View on Wikipedia
from Wikipedia

SI derived units are units of measurement derived from the seven SI base units specified by the International System of Units (SI). They can be expressed as a product (or ratio) of one or more of the base units, possibly scaled by an appropriate power of exponentiation (see: Buckingham π theorem). Some are dimensionless, as when the units cancel out in ratios of like quantities. SI coherent derived units involve only a trivial proportionality factor, not requiring conversion factors.

The SI has special names for 22 of these coherent derived units (for example, hertz, the SI unit of measurement of frequency), but the rest merely reflect their derivation: for example, the square metre (m2), the SI derived unit of area; and the kilogram per cubic metre (kg/m3 or kg⋅m−3), the SI derived unit of density.

The names of SI coherent derived units, when written in full, are always in lowercase. However, the symbols for units named after persons are written with an uppercase initial letter. For example, the symbol for hertz is "Hz", while the symbol for metre is "m".[1]

Special names

[edit]

The International System of Units assigns special names to 22 derived units, which includes two dimensionless derived units, the radian (rad) and the steradian (sr).

Named units derived from SI base units[2]
Name Symbol Quantity Equivalents SI base unit
Equivalents
hertz Hz frequency 1/s s−1
radian rad angle m/m 1
steradian sr solid angle m2/m2 1
newton N force, weight kg⋅m/s2 kg⋅m⋅s−2
pascal Pa pressure, stress N/m2 kg⋅m−1⋅s−2
joule J energy, work, heat m⋅N, C⋅V, W⋅s kg⋅m2⋅s−2
watt W power, radiant flux J/s, V⋅A kg⋅m2⋅s−3
coulomb C electric charge or quantity of electricity s⋅A, F⋅V s⋅A
volt V voltage, electrical potential difference, electromotive force W/A, J/C kg⋅m2⋅s−3⋅A−1
farad F electrical capacitance C/V, s/Ω kg−1⋅m−2⋅s4⋅A2
ohm Ω electrical resistance, impedance, reactance 1/S, V/A kg⋅m2⋅s−3⋅A−2
siemens S electrical conductance 1/Ω, A/V kg−1⋅m−2⋅s3⋅A2
weber Wb magnetic flux J/A, T⋅m2,V⋅s kg⋅m2⋅s−2⋅A−1
tesla T magnetic induction, magnetic flux density V⋅s/m2, Wb/m2, N/(A⋅m) kg⋅s−2⋅A−1
henry H electrical inductance V⋅s/A, Ω⋅s, Wb/A kg⋅m2⋅s−2⋅A−2
degree Celsius °C temperature relative to 273.15 K K K
lumen lm luminous flux cd⋅sr cd
lux lx illuminance lm/m2 cd⋅m−2
becquerel Bq radioactivity (decays per unit time) 1/s s−1
gray Gy absorbed dose (of ionizing radiation) J/kg m2⋅s−2
sievert Sv equivalent dose (of ionizing radiation) J/kg m2⋅s−2
katal kat catalytic activity mol/s s−1⋅mol.

By field of application

[edit]

Kinematics

[edit]
Name Symbol Quantity Expression in terms
of SI base units
metre per second m/s speed, velocity m⋅s−1
metre per second squared m/s2 acceleration m⋅s−2
metre per second cubed m/s3 jerk, jolt m⋅s−3
metre per second to the fourth m/s4 snap, jounce m⋅s−4
kilogram metre per second to the third kg⋅m/s3 yank m⋅kg⋅s−3
radian per second rad/s angular velocity s−1
radian per second squared rad/s2 angular acceleration s−2
hertz per second Hz/s frequency drift s−2
cubic metre per second m3/s volumetric flow m3⋅s−1

Mechanics

[edit]
Name Symbol Quantity Expression in terms
of SI base units
square metre m2 area m2
cubic metre m3 volume m3
newton-second N⋅s momentum, impulse m⋅kg⋅s−1
newton metre second N⋅m⋅s angular momentum m2⋅kg⋅s−1
newton-metre N⋅m = J/rad torque, moment of force m2⋅kg⋅s−2
newton per second N/s yank m⋅kg⋅s−3
reciprocal metre m−1 wavenumber, optical power, curvature, spatial frequency m−1
kilogram per square metre kg/m2 area density m−2⋅kg
kilogram per cubic metre kg/m3 density, mass density m−3⋅kg
cubic metre per kilogram m3/kg specific volume m3⋅kg−1
joule-second J⋅s action m2⋅kg⋅s−1
joule per kilogram J/kg specific energy m2⋅s−2
joule per cubic metre J/m3 energy density m−1⋅kg⋅s−2
newton per metre N/m = J/m2 surface tension, stiffness kg⋅s−2
watt per square metre W/m2 heat flux density, irradiance kg⋅s−3
square metre per second m2/s kinematic viscosity, thermal diffusivity, diffusion coefficient m2⋅s−1
pascal-second Pa⋅s = N⋅s/m2 dynamic viscosity m−1⋅kg⋅s−1
kilogram per metre kg/m linear mass density m−1⋅kg
kilogram per second kg/s mass flow rate kg⋅s−1
watt per steradian square metre W/(sr⋅m2) radiance kg⋅s−3
watt per steradian cubic metre W/(sr⋅m3) radiance m−1⋅kg⋅s−3
watt per metre W/m spectral power m⋅kg⋅s−3
gray per second Gy/s absorbed dose rate m2⋅s−3
metre per cubic metre m/m3 fuel efficiency m−2
watt per cubic metre W/m3 spectral irradiance, power density m−1⋅kg⋅s−3
joule per square metre second J/(m2⋅s) energy flux density kg⋅s−3
reciprocal pascal Pa−1 compressibility m⋅kg−1⋅s2
joule per square metre J/m2 radiant exposure kg⋅s−2
kilogram square metre kg⋅m2 moment of inertia m2⋅kg
newton metre second per kilogram N⋅m⋅s/kg specific angular momentum m2⋅s−1
watt per steradian W/sr radiant intensity m2⋅kg⋅s−3
watt per steradian metre W/(sr⋅m) spectral intensity m⋅kg⋅s−3

Chemistry

[edit]
Name Symbol Quantity Expression in terms
of SI base units
mole per cubic metre mol/m3 molarity, amount of substance concentration m−3⋅mol
cubic metre per mole m3/mol molar volume m3⋅mol−1
joule per kelvin mole J/(K⋅mol) molar heat capacity, molar entropy m2⋅kg⋅s−2⋅K−1⋅mol−1
joule per mole J/mol molar energy m2⋅kg⋅s−2⋅mol−1
siemens square metre per mole S⋅m2/mol molar conductivity kg−1⋅s3⋅A2⋅mol−1
mole per kilogram mol/kg molality kg−1⋅mol
kilogram per mole kg/mol molar mass kg⋅mol−1
cubic metre per mole second m3/(mol⋅s) catalytic efficiency m3⋅s−1⋅mol−1

Electromagnetics

[edit]
Name Symbol Quantity Expression in terms
of SI base units
coulomb per square metre C/m2 electric displacement field, polarization density m−2⋅s⋅A
coulomb per cubic metre C/m3 electric charge density m−3⋅s⋅A
ampere per square metre A/m2 electric current density m−2⋅A
siemens per metre S/m electrical conductivity m−3⋅kg−1⋅s3⋅A2
farad per metre F/m permittivity m−3⋅kg−1⋅s4⋅A2
henry per metre H/m magnetic permeability m⋅kg⋅s−2⋅A−2
volt per metre V/m electric field strength m⋅kg⋅s−3⋅A−1
ampere per metre A/m magnetization, magnetic field strength m−1⋅A
coulomb per kilogram C/kg exposure (X and gamma rays) kg−1⋅s⋅A
ohm metre Ω⋅m resistivity m3⋅kg⋅s−3⋅A−2
coulomb per metre C/m linear charge density m−1⋅s⋅A
joule per tesla J/T magnetic dipole moment m2⋅A
square metre per volt second m2/(V⋅s) electron mobility kg−1⋅s2⋅A
reciprocal henry H−1 magnetic reluctance m−2⋅kg−1⋅s2⋅A2
weber per metre Wb/m magnetic vector potential m⋅kg⋅s−2⋅A−1
weber metre Wb⋅m magnetic moment m3⋅kg⋅s−2⋅A−1
tesla metre T⋅m magnetic rigidity m⋅kg⋅s−2⋅A−1
ampere radian A⋅rad magnetomotive force A
metre per henry m/H magnetic susceptibility m−1⋅kg−1⋅s2⋅A2

Photometry

[edit]
Name Symbol Quantity Expression in terms
of SI base units
lumen second lm⋅s luminous energy s⋅cd
lux second lx⋅s luminous exposure m−2⋅s⋅cd
candela per square metre cd/m2 luminance m−2⋅cd
lumen per watt lm/W luminous efficacy m−2⋅kg−1⋅s3⋅cd

Thermodynamics

[edit]
Name Symbol Quantity Expression in terms
of SI base units
joule per kelvin J/K heat capacity, entropy m2⋅kg⋅s−2⋅K−1
joule per kilogram kelvin J/(K⋅kg) specific heat capacity, specific entropy m2⋅s−2⋅K−1
watt per metre kelvin W/(m⋅K) thermal conductivity m⋅kg⋅s−3⋅K−1
kelvin per watt K/W thermal resistance m−2⋅kg−1⋅s3⋅K
reciprocal kelvin K−1 thermal expansion coefficient K−1
kelvin per metre K/m temperature gradient m−1⋅K

Other units used with SI

[edit]

Some other units such as the hour, litre, tonne, bar, and electronvolt are not SI units, but are widely used in conjunction with SI units.

Supplementary units

[edit]

Until 1995, the SI classified the radian and the steradian as supplementary units, but this designation was abandoned and the units were grouped as derived units.[3]

See also

[edit]

References

[edit]

Bibliography

[edit]
[edit]
Revisions and contributorsEdit on WikipediaRead on Wikipedia

SI derived unit

View on Grokipedia
from Grokipedia
In the International System of Units (SI), derived units are those formed by combining the seven base units through products of integer powers of those units, enabling the expression of measurements for physical quantities that are not fundamental but composed of basic dimensions such as length, mass, time, electric current, thermodynamic temperature, amount of substance, and luminous intensity. These derived units ensure coherence within the SI system, meaning that when physical equations are written using SI units, the numerical factors are exactly 1 without additional constants, facilitating precise scientific calculations and international standardization.[1] The SI, established by the General Conference on Weights and Measures (CGPM) and maintained by the International Bureau of Weights and Measures (BIPM), defines derived units solely in terms of base units or other derived units, with the system's foundation now anchored in fixed values of seven defining constants since the 2019 revision. Of the infinite possible derived units, 22 have been assigned special names and symbols by the CGPM for frequently used quantities in science, engineering, and everyday applications, such as the newton (N) for force (kg·m·s⁻²), the joule (J) for energy (kg·m²·s⁻²), the watt (W) for power (kg·m²·s⁻³), and the hertz (Hz) for frequency (s⁻¹).[1] These named units simplify notation and reduce errors in complex expressions, while all other derived units can be expressed directly in terms of base units or named derived units. The selection of special names reflects historical and practical significance, with ongoing reviews by the International Committee for Weights and Measures (CIPM) to adapt to evolving metrological needs.[1]
Derived QuantityNameSymbolExpression in Base Units
ForcenewtonNkg·m·s⁻²
PressurepascalPakg·m⁻¹·s⁻²
EnergyjouleJkg·m²·s⁻²
PowerwattWkg·m²·s⁻³
Electric chargecoulombCs·A
Electric potential differencevoltVkg·m²·s⁻³·A⁻¹
CapacitancefaradFkg⁻¹·m⁻²·s⁴·A²
This table illustrates select examples of coherent derived units with special names, highlighting their dimensional compositions. Overall, SI derived units underpin global measurement consistency, supporting fields from physics and chemistry to industry and trade.[2]

Fundamentals of SI Units

Base Units and the SI System

The International System of Units (SI), known as the modern form of the metric system, was formally adopted in 1960 by the 11th General Conference on Weights and Measures (CGPM) through Resolution 12, which established a coherent framework for scientific and everyday measurements based on seven base quantities and their corresponding units.[3][4] This system builds on earlier metric developments, such as the metre-kilogram-second (MKS) framework, to provide a universal standard that facilitates international consistency in measurement.[5] The SI defines seven base quantities, each with a dedicated base unit, selected to cover fundamental aspects of physical measurement without redundancy. These are: length, measured in the metre (m); mass, in the kilogram (kg); time, in the second (s); electric current, in the ampere (A); thermodynamic temperature, in the kelvin (K); amount of substance, in the mole (mol); and luminous intensity, in the candela (cd).[6][4]
Base QuantityBase UnitSymbolDefinition (post-2019)
LengthmetremThe metre is defined by taking the fixed numerical value of the speed of light in vacuum c to be 299792458 m/s, with the second fixed by definition.[7]
MasskilogramkgThe kilogram is defined by taking the fixed numerical value of the Planck constant h to be 6.62607015 × 10-34 J s, with the joule and second fixed by definition.
TimesecondsThe second is defined by taking the fixed numerical value of the caesium frequency ΔνCs, the unperturbed ground-state hyperfine transition frequency of the caesium-133 atom, to be 9192631770 Hz.[8]
Electric currentampereAThe ampere is defined by taking the fixed numerical value of the elementary charge e to be 1.602176634 × 10-19 C, with the coulomb and second fixed by definition.
Thermodynamic temperaturekelvinKThe kelvin is defined by taking the fixed numerical value of the Boltzmann constant k to be 1.380649 × 10-23 J/K, with the joule and second fixed by definition.
Amount of substancemolemolThe mole is defined by taking the fixed numerical value of the Avogadro constant NA to be 6.02214076 × 1023 mol-1.
Luminous intensitycandelacdThe candela is defined by taking the fixed numerical value of the luminous efficacy of monochromatic radiation of frequency 540 × 1012 Hz, Kcd, to be 683 lm/W, with the second and metre fixed by definition.
The definitions of these base units have evolved historically to enhance precision and universality; initially artifact-based (e.g., the kilogram as a platinum-iridium prototype), they underwent significant refinement, culminating in the 2019 redefinition approved by the 26th CGPM in Resolution 1, which anchors all units to fixed values of seven fundamental constants of nature, such as the speed of light c for the metre and the Planck constant h for the kilogram.[9][4] This shift, effective from 20 May 2019, ensures long-term stability independent of physical artifacts and aligns the SI more closely with theoretical physics.[5] A key feature of the SI is its coherence, meaning that the product or quotient of any two or more base units yields a derived unit without additional numerical factors other than unity in the equations of physics, promoting simplicity in calculations and formulas.[4] Derived units are thus formed as algebraic combinations of these base units.[10]

Definition of Derived Units

In the International System of Units (SI), derived units are those used to express quantities that are functions of the seven base quantities, formed by taking products or quotients of powers of the corresponding base units.[4] These units arise from the algebraic relations linking derived quantities to base quantities, such as velocity, which is defined as the quotient of length and time, yielding the unit metre per second (m/s).[4] Every physical quantity in the SI possesses a dimension, expressed as a product of powers of the dimensions of the base quantities, denoted symbolically as [Q]=LaMbTcIdΘeNfJg[Q] = \mathrm{L}^a \mathrm{M}^b \mathrm{T}^c \mathrm{I}^d \mathrm{\Theta}^e \mathrm{N}^f \mathrm{J}^g, where L, M, T, I, Θ, N, and J represent length, mass, time, electric current, thermodynamic temperature, amount of substance, and luminous intensity, respectively, and the exponents a through g are integers (positive, negative, or zero).[4] The derived unit for a given quantity must then match this dimensional expression through appropriate combinations of base units, ensuring dimensional homogeneity in physical equations.[4] A key feature of the SI is the principle of coherence, whereby coherent derived units are specifically chosen as products of integer powers of base units with no additional numerical factor other than unity.[4] This ensures that the equations between numerical values of physical quantities take exactly the same form as the equations between the quantities themselves, eliminating the need for conversion factors in fundamental relations.[4] For instance, the coherent derived unit for area is the square metre (m²), obtained as length squared, and for volume, it is the cubic metre (m³), as length cubed.[4]

Coherent Derived Units

Units with Special Names

Coherent derived units in the SI that appear frequently in scientific and technical contexts are assigned special names and symbols to enhance clarity and convenience, thereby avoiding lengthy expressions composed solely of base units. For example, the unit for force is designated as the newton rather than kilogram meter per second squared.[4] These special names originated from earlier metric systems and were progressively formalized through decisions by the General Conference on Weights and Measures (CGPM). The 9th CGPM in 1948 adopted names such as newton, joule, watt, and others derived from the metre-kilogram-second (MKS) system.[4] The 11th CGPM in 1960 established the SI and confirmed many of these names, including hertz, pascal, coulomb, volt, and farad.[4] Subsequent conferences added names like becquerel and gray (15th CGPM, 1975), sievert (16th CGPM, 1979), and katal (21st CGPM, 1999) to address emerging needs in radioactivity, radiation protection, and chemistry.[4] The 22 coherent derived units with special names, as defined in the 9th edition of the SI Brochure (2019, revised 2025), are presented in the table below. Each entry includes the unit name, symbol, physical quantity, expression in terms of SI base units, and a brief etymology.[4]
NameSymbolQuantityExpression in Terms of Base UnitsEtymology
radianradplane angle1Derived from "radius," referring to the arc length equal to the radius.[4]
steradiansrsolid angle1Derived from Greek "stereos" (solid) and "radius."[4]
hertzHzfrequencys⁻¹Named after Heinrich Hertz, German physicist who studied electromagnetic waves.[4]
newtonNforce, weightkg⋅m⋅s⁻²Named after Sir Isaac Newton, English mathematician and physicist.[4]
pascalPapressure, stresskg⋅m⁻¹⋅s⁻²Named after Blaise Pascal, French mathematician and physicist.[4]
jouleJenergy, work, quantity of heatkg⋅m²⋅s⁻²Named after James Prescott Joule, English physicist.[4]
wattWpower, radiant fluxkg⋅m²⋅s⁻³Named after James Watt, Scottish engineer and inventor.[4]
coulombCelectric charge, quantity of electricitys⋅ANamed after Charles-Augustin de Coulomb, French physicist.[4]
voltVelectric potential, potential difference, electromotive forcekg⋅m²⋅s⁻³⋅A⁻¹Named after Alessandro Volta, Italian physicist.[4]
faradFcapacitancekg⁻¹⋅m⁻²⋅s⁴⋅A²Named after Michael Faraday, English physicist and chemist.[4]
ohmΩelectric resistance, impedance, reactancekg⋅m²⋅s⁻³⋅A⁻²Named after Georg Simon Ohm, German physicist.[4]
siemensSelectric conductance, admittance, susceptancekg⁻¹⋅m⁻²⋅s³⋅A²Named after Ernst Werner von Siemens, German industrialist and inventor.[4]
weberWbmagnetic fluxkg⋅m²⋅s⁻²⋅A⁻¹Named after Wilhelm Eduard Weber, German physicist.[4]
teslaTmagnetic flux density, magnetic inductionkg⋅s⁻²⋅A⁻¹Named after Nikola Tesla, Serbian-American inventor and engineer.[4]
henryHinductance, mutual inductancekg⋅m²⋅s⁻²⋅A⁻²Named after Joseph Henry, American physicist.[4]
degree Celsius°CCelsius temperature (interval)KNamed after Anders Celsius, Swedish astronomer.[4]
lumenlmluminous fluxcd⋅srFrom Latin "lumen," meaning light.[4]
luxlxilluminance, illuminationcd⋅m⁻²From Latin "lux," meaning light.[4]
becquerelBqradioactive activitys⁻¹Named after Henri Becquerel, French physicist and discoverer of radioactivity.[4]
grayGyabsorbed dose, specific energy imparted, kerma, absorbed dose indexm²⋅s⁻²Named after Louis Harold Gray, British radiobiologist.[4]
sievertSvdose equivalent, dose equivalent indexm²⋅s⁻²Named after Rolf Maximilian Sievert, Swedish medical physicist.[4]
katalkatcatalytic activitymol⋅s⁻¹Derived from Greek "katalyein," meaning to dissolve or loosen.[4]

Units without Special Names

Coherent derived units without special names are those expressed directly as products or quotients of powers of SI base units, with no additional numerical factors other than unity. These units maintain the coherence of the SI system by ensuring that the algebraic relations between quantities translate directly into equations between their numerical values without conversion factors. For instance, the unit for area is the square metre, denoted as m², formed by the square of the base unit of length. Similarly, volume uses the cubic metre, m³, as the product of three length units. Speed, or velocity magnitude, is represented by the metre per second, m/s, which is length divided by time. Acceleration follows as metre per second squared, m/s², incorporating time in the denominator twice. Density is kilogram per cubic metre, kg/m³, combining mass with the inverse of volume. Momentum employs kilogram metre per second, kg⋅m/s, as the product of mass and speed. For frequency, the coherent unit is the reciprocal second, s⁻¹, though it has a special name alternative in common use. These compound units preserve coherence in physical equations by aligning dimensions directly. Consider the kinetic energy formula $ E = \frac{1}{2} m v^2 $, where mass $ m $ is in kilograms (kg) and speed $ v $ is in metres per second (m/s); the resulting energy unit is then kg⋅m²⋅s⁻², which corresponds to the joule (detailed elsewhere). This direct substitution avoids scaling factors, allowing the equation to hold numerically as it does dimensionally. While these units provide a systematic and universal approach to measurement, their compound expressions can become lengthy for quantities involving multiple base units or higher powers. In practice, this complexity often motivates the assignment of special names to frequently used derived units, enhancing readability and reducing error in complex calculations.

Derived Units by Physical Dimension

Dimensions Involving Length and Time

Derived units involving only the dimensions of length [L] and time [T] form a foundational subset in the SI system, enabling the quantification of kinematic and dynamic phenomena without introducing other base quantities. These units are coherent, meaning they arise directly from products or quotients of the base units of length (metre, m) and time (second, s) with numerical factors of unity, ensuring that fundamental physical equations retain their simplest numerical form when expressed in SI units.[4] The dimensional formula for velocity, a measure of speed or rate of change of position, is [L T^{-1}], with the coherent SI unit being the metre per second (m/s). This unit represents the distance traveled in one second, directly linking the metre—defined since 1983 as the distance light travels in vacuum in 1/299 792 458 of a second—to the second, which is based on the caesium-133 hyperfine transition frequency of exactly 9 192 631 770 Hz. As of November 2025, ongoing efforts by the Consultative Committee for Time and Frequency (CCTF) and the CGPM are advancing proposals to redefine the second based on optical transitions for improved accuracy, with draft resolutions under consideration.[11][12] The 1983 redefinition of the metre, adopted by the 17th General Conference on Weights and Measures (CGPM), anchored length measurements to the invariant speed of light, thereby enhancing the precision and universality of velocity derivations across length-time combinations.[7][4] Acceleration, the rate of change of velocity, has the dimensional formula [L T^{-2}] and the coherent unit metre per second squared (m/s²). This unit captures changes in motion, such as gravitational acceleration near Earth's surface at approximately 9.8 m/s². Coherence is exemplified in kinematic equations, such as the linear form $ v = u + at $, where initial velocity $ u $ and final velocity $ v $ are in m/s, acceleration $ a $ is in m/s², and time $ t $ is in s; substituting these units yields m/s = m/s + (m/s²) × s, confirming dimensional balance without conversion factors. This property simplifies calculations in mechanics, as the equation's numerical coefficients remain unchanged in the SI system.[4] Frequency, denoting cycles or oscillations per unit time, possesses the dimensional formula [T^{-1}] and the coherent unit second inverse (s^{-1}), which received the special name hertz (Hz) in 1960 by the 11th CGPM to honor Heinrich Hertz's contributions to electromagnetism. One hertz equals one event per second, applicable to phenomena like sound waves or atomic transitions underlying the second's definition. While primarily time-based, frequency often pairs with length in wave contexts, such as wavelength $ \lambda = c / f $, where speed of light $ c $ is in m/s and frequency $ f $ in Hz, yielding metres.[4] Angular velocity, the rate of rotational change, shares the [T^{-1}] dimension and uses the unit radian per second (rad/s). The radian (rad), historically a supplementary unit since the 11th CGPM in 1960,[3] was reclassified as a derived dimensionless unit in 1995 by the 20th CGPM, as it equals the ratio of arc length to radius (both in metres), resulting in m/m = 1. Thus, rad/s coherently expresses angular rates, such as Earth's rotation at about 7.29 × 10^{-5} rad/s, integrating seamlessly with linear velocity via $ v = \omega r $ (m/s = rad/s × m). This evolution reflects the SI's refinement toward treating plane angles as derived quantities.[13][14][4]

Dimensions Involving Mass and Force

In the International System of Units (SI), dimensions involving mass and force primarily combine the base dimensions of mass [M], length [L], and time [T] to quantify mechanical phenomena such as motion, interaction, and energy transfer. These derived units are coherent, meaning they follow directly from products and powers of the SI base units without additional numerical factors. The foundational quantity here is force, which arises from Newton's second law of motion, expressed as F=maF = ma, where FF is force, mm is mass, and aa is acceleration.[4] The dimensional formula for force is [M][L][T]−2[M][L][T]^{-2}, and its SI unit is the newton (N), defined as the force that imparts an acceleration of one meter per second squared to a mass of one kilogram, yielding 1 N=1 kg⋅m⋅s−21\ \mathrm{N} = 1\ \mathrm{kg \cdot m \cdot s^{-2}}. This unit was adopted as a special name by the 9th General Conference on Weights and Measures (CGPM) in 1948. Momentum, a related quantity representing the product of mass and velocity, has the dimensional formula [M][L][T]−1[M][L][T]^{-1} and the unit kg⋅m⋅s−1\mathrm{kg \cdot m \cdot s^{-1}}, without a special name.[4][4][4] Pressure, defined as force per unit area, has the dimensional formula [M][L]−1[T]−2[M][L]^{-1}[T]^{-2} and the unit pascal (Pa), equivalent to 1 Pa=1 N/m2=1 kg⋅m−1⋅s−21\ \mathrm{Pa} = 1\ \mathrm{N/m^2} = 1\ \mathrm{kg \cdot m^{-1} \cdot s^{-2}}. The pascal was adopted as a special name by the 14th CGPM in 1971, honoring Blaise Pascal (1623–1662), the French mathematician, physicist, and philosopher known for his contributions to hydrodynamics and atmospheric pressure studies. Energy or work, the scalar product of force and displacement, carries the dimensional formula [M][L]2[T]−2[M][L]^2[T]^{-2} and the unit joule (J), where 1 J=1 N⋅m=1 kg⋅m2⋅s−21\ \mathrm{J} = 1\ \mathrm{N \cdot m} = 1\ \mathrm{kg \cdot m^2 \cdot s^{-2}}, also named in 1948 by the 9th CGPM after James Prescott Joule. Power, the rate of energy transfer, has the dimensional formula [M][L]2[T]−3[M][L]^2[T]^{-3} and the unit watt (W), defined as 1 W=1 J/s=1 kg⋅m2⋅s−31\ \mathrm{W} = 1\ \mathrm{J/s} = 1\ \mathrm{kg \cdot m^2 \cdot s^{-3}}, adopted in 1960 by the 11th CGPM to honor James Watt.[4][4][4][4][4][4] Other derived units in this category include surface tension, with dimensional formula [M][T]−2[M][T]^{-2} and unit N/m=kg⋅s−2\mathrm{N/m} = \mathrm{kg \cdot s^{-2}}, representing force per unit length at interfaces, and dynamic viscosity, with dimensional formula [M][L]−1[T]−1[M][L]^{-1}[T]^{-1} and unit Pa⋅s=kg⋅m−1⋅s−1\mathrm{Pa \cdot s} = \mathrm{kg \cdot m^{-1} \cdot s^{-1}}, measuring a fluid's resistance to shear flow. These units enable precise quantification in mechanics, from structural engineering to fluid dynamics, ensuring consistency across scientific and technical applications.[4][4]
QuantityDimensional FormulaSI UnitExpression in Base Units
Momentum[M][L][T]−1[M][L][T]^{-1}kg⋅m⋅s⁻¹kg⋅m⋅s⁻¹
Force[M][L][T]−2[M][L][T]^{-2}Newton (N)kg⋅m⋅s⁻²
Pressure[M][L]−1[T]−2[M][L]^{-1}[T]^{-2}Pascal (Pa)kg⋅m⁻¹⋅s⁻²
Energy/Work[M][L]2[T]−2[M][L]^2[T]^{-2}Joule (J)kg⋅m²⋅s⁻²
Power[M][L]2[T]−3[M][L]^2[T]^{-3}Watt (W)kg⋅m²⋅s⁻³
Surface Tension[M][T]−2[M][T]^{-2}N⋅m⁻¹kg⋅s⁻²
Dynamic Viscosity[M][L]−1[T]−1[M][L]^{-1}[T]^{-1}Pa⋅skg⋅m⁻¹⋅s⁻¹

Dimensions Involving Electric Current and Charge

In the International System of Units (SI), electric current is a base quantity with dimension symbol [I], and its SI unit is the ampere (A).[4] Electric charge, a derived quantity, has the dimensional formula [I T], where [T] denotes time, and its coherent SI unit is the coulomb (C), defined as C = A ⋅ s.[4] This unit quantifies the amount of electric charge transported by a current of one ampere in one second, establishing the foundational role of [I] in electromagnetic dimensions.[4] Electric potential difference, another key derived quantity, has the dimensional formula [M L² T⁻³ I⁻¹], where [M] and [L] represent mass and length, respectively, linking electrical phenomena to mechanical energy components through the joule (J = kg ⋅ m² ⋅ s⁻²).[4] Its coherent SI unit is the volt (V), defined as V = kg ⋅ m² ⋅ s⁻³ ⋅ A⁻¹, equivalent to the potential difference across a conductor carrying one ampere of current that dissipates one watt of power.[4] From this, further derived units emerge, such as capacitance with unit farad (F = C / V = kg⁻¹ ⋅ m⁻² ⋅ s⁴ ⋅ A²), representing the ability to store one coulomb of charge at one volt.[4] Electrical resistance has the dimensional formula [M L² T⁻³ I⁻²] and unit ohm (Ω = V / A = kg ⋅ m² ⋅ s⁻³ ⋅ A⁻²), measuring opposition to current flow.[4] This coherence is exemplified in Ohm's law, V = I R, where the dimensions align as [M L² T⁻³ I⁻¹] = [I] ⋅ [M L² T⁻³ I⁻²], ensuring consistent numerical relations without conversion factors in SI equations.[15] Magnetic flux, with dimensional formula [M L² T⁻² I⁻¹], uses the weber (Wb = V ⋅ s = kg ⋅ m² ⋅ s⁻² ⋅ A⁻¹), while inductance has [M L² T⁻² I⁻²] and unit henry (H = Wb / A = kg ⋅ m² ⋅ s⁻² ⋅ A⁻²).[4] The definition of the ampere underwent a significant revision in 2019, when the 26th General Conference on Weights and Measures (CGPM) fixed the value of the elementary charge e exactly at 1.602 176 634 × 10⁻¹⁹ C, effective from 20 May 2019.[4] This replaced the prior definition based on the force between current-carrying conductors, anchoring the ampere—and thus all charge-related units—to fundamental constants for greater precision and universality.[4]

Derived Units by Field of Application

Mechanics and Dynamics

In mechanics and dynamics, the newton (N), defined as the force required to accelerate a one-kilogram mass by one meter per second squared (kg⋅m⋅s⁻²), is fundamental for quantifying forces in structural engineering, such as the load-bearing capacities of bridges or buildings where forces are expressed in newtons to ensure material integrity.[4] The joule (J), equivalent to one newton-meter (N⋅m or kg⋅m²⋅s⁻²), measures energy transferred in mechanical processes, including kinetic energy dissipated during vehicle collisions, where impact energies can reach thousands of joules depending on speed and mass.[16] Similarly, the pascal (Pa), or one newton per square meter (N⋅m⁻² or kg⋅m⁻¹⋅s⁻²), quantifies pressure in fluid dynamics, such as hydraulic systems in machinery, and stress in solid materials under deformation.[17] Key derived quantities in classical mechanics include impulse, which represents the change in momentum and has units of N⋅s (or kg⋅m⋅s⁻¹), applied in analyzing impacts like those in sports equipment design to minimize injury.[4] Torque, the rotational equivalent of force, uses units of N⋅m (kg⋅m²⋅s⁻²) and is distinct from energy despite dimensional similarity, as the joule is not used for torque to avoid confusion in engineering contexts like bolt tightening.[18] Stress, measured in pascals, describes force per unit area in materials under load, while strain is dimensionless; together, they inform elastic moduli in structural analysis, such as in steel beams where stresses rarely exceed 250 MPa.[17] Moment of inertia, a measure of rotational resistance, has coherent SI units of kg⋅m² and is essential for calculating angular acceleration in systems like flywheels.[4] The work-energy theorem states that the net work done on an object equals the change in its mechanical energy, expressed as $ W = \Delta E $, where both work $ W $ and energy $ \Delta E $ are in joules, linking force application over distance to energy transformations in dynamic systems. Power, the rate of work or energy transfer, is given by $ P = F \cdot v $, with units of watts (W = J/s = N⋅m/s), illustrating how force $ F $ (in newtons) applied over velocity $ v $ (in m/s) yields power in applications like engine performance.[19] In modern aerospace engineering, derived units like the newton are critical for thrust measurements; for instance, NASA's model rocket engines, such as the C6-4, produce an average thrust of 6 N to propel payloads, scaling to millions of newtons in large orbital launch vehicles for precise trajectory control.[20]

Electromagnetism

In electromagnetism, SI derived units quantify fundamental quantities such as electric potential, current, and magnetic fields, enabling precise descriptions of phenomena ranging from circuit behavior to electromagnetic waves. The volt (V), the unit of electric potential difference and electromotive force, is expressed as kg·m²·s⁻³·A⁻¹ and represents the potential difference that produces 1 joule of energy per coulomb of charge.[4] In electrical circuits, voltage drives current flow, with the ampere (A), the base unit of electric current, serving as the reference; for instance, Ohm's law relates voltage, current, and resistance via V = I·R, where resistance is measured in ohms (Ω = kg·m²·s⁻³·A⁻²).[4] Current density, denoted in amperes per square meter (A/m²), describes the electric current per unit cross-sectional area and is crucial for analyzing conductors and semiconductors, expressed dimensionally as A·m⁻².[4] Magnetic field strength uses amperes per meter (A/m), quantifying the magnetomotive force per unit length in materials like solenoids.[4] Permittivity (F/m), the measure of a material's ability to store electric charge, and permeability (H/m), which indicates magnetic response, are both per-unit-length derived units: F/m = kg⁻¹·m⁻³·s⁴·A² and H/m = kg·m·s⁻²·A⁻², respectively, influencing wave propagation in media.[4] Key examples include the electric field strength, in volts per meter (V/m = kg·m·s⁻³·A⁻¹), which describes the force per unit charge in electrostatics, and the magnetic flux density, in teslas (T = kg·s⁻²·A⁻¹), essential for motors and MRI imaging.[4] Impedance (Ω), extending resistance to AC circuits, combines these in phasor analysis for signal processing.[4] A foundational equation is Coulomb's law, expressing the electrostatic force between charges:
F=14πϵ0q1q2r2 F = \frac{1}{4\pi\epsilon_0} \frac{q_1 q_2}{r^2}
where FF is in newtons (N = kg·m·s⁻²), q1q_1 and q2q_2 in coulombs (C = A·s), rr in meters (m), and ϵ0\epsilon_0 (vacuum permittivity) in F/m; unit analysis confirms consistency, as N derives from C²/(F·m²).[4] In quantum electromagnetism, the 2019 SI revision—effective since May 20, 2019—facilitates precise photon energy calculations, where the electronvolt (eV), accepted for use with SI despite being non-SI, equals exactly 1.602176634 × 10⁻¹⁹ J and quantifies energies in atomic transitions and particle interactions.[4][21]

Thermodynamics and Chemistry

In thermodynamics and chemistry, SI derived units quantify properties related to heat, energy transfer, substance amounts, and reaction dynamics, building on base units like the kelvin (K) for temperature, mole (mol) for amount of substance, and joule (J) for energy.[4] These units enable precise descriptions of thermal processes, phase changes, and chemical equilibria without introducing non-coherent factors.[22] For instance, heat-related quantities often combine energy with temperature, while chemical ones incorporate the mole to express per-substance metrics. The dalton (Da), an accepted unit for atomic and molecular mass used with the SI, was revised in the August 2025 update to the SI Brochure (version 3.02) based on the 2022 CODATA adjustment of fundamental constants.[4] Heat capacity, denoted C, measures the energy required to raise the temperature of a system by one kelvin and has the unit joule per kelvin (J/K), dimensionally kg⋅m²⋅s⁻²⋅K⁻¹.[4] The molar heat capacity, Cm, extends this to per mole of substance, using J/(mol⋅K) or kg⋅m²⋅s⁻²⋅mol⁻¹⋅K⁻¹, which is essential for comparing thermal responses in gases or solutions.[22] Entropy, S, quantifies the dispersal of energy or disorder in a system and shares the unit J/K (kg⋅m²⋅s⁻²⋅K⁻¹), as established by the second law of thermodynamics.[4] In chemical contexts, concentration c represents the amount of substance per unit volume, with the unit mol/m³ (mol⋅m⁻³), facilitating analysis of solution properties and reaction progress.[22] Reaction rate v, the change in concentration over time, uses mol/(m³⋅s) or mol⋅m⁻³⋅s⁻¹, capturing the speed of chemical transformations in homogeneous systems.[4] Enthalpy H, the total heat content at constant pressure, is expressed in joules (J, kg⋅m²⋅s⁻²), while Gibbs free energy G—the maximum reversible work available—also uses J, both often reported as molar values like kJ/mol for standard conditions.[22] Chemical potential μ, the partial molar Gibbs energy, employs J/mol (kg⋅m²⋅s⁻²⋅mol⁻¹) to describe how adding a substance affects system energy.[4] The ideal gas law illustrates unit coherence in thermodynamics:
PV=nRT PV = nRT

where pressure P is in pascals (Pa, kg⋅m⁻¹⋅s⁻²), volume V in cubic meters (m³), amount n in moles (mol), temperature T in kelvin (K), and the gas constant R in J/(mol⋅K) (kg⋅m²⋅s⁻²⋅mol⁻¹⋅K⁻¹), yielding Pa⋅m³ = J on both sides.[22] In electrochemistry, the volt (V, kg⋅m²⋅s⁻³⋅A⁻¹) serves as the unit for potential difference, representing energy per unit charge in cells and driving reactions like electrolysis.[4] For modern biochemistry, catalytic activity in enzymes is measured in katals (kat, mol⋅s⁻¹), where 1 kat equals one mole of substance transformed per second, standardizing enzyme kinetics.[4]

Photometry and Radiometry

Photometry measures light in quantities adapted to human visual perception, while radiometry quantifies electromagnetic radiation independent of vision. In the SI system, photometric units are derived from the base unit candela (cd) for luminous intensity and the supplementary unit steradian (sr) for solid angle, with radiometric units building on the watt (W) for power. These units enable precise characterization of light sources and illumination in applications ranging from lighting design to optical instrumentation.[4] Key photometric derived units include luminous flux, measured in lumens (lm), defined as the product of luminous intensity in candelas and solid angle in steradians: lm = cd ⋅ sr. This represents the total visible light output from a source, weighted by the eye's sensitivity. Illuminance, in lux (lx), quantifies light incident on a surface and is derived as luminous flux per unit area: lx = lm / m². Luminance, in candelas per square meter (cd/m²), describes the brightness of a surface or source in a given direction, combining luminous intensity per unit projected area.[4][23] Radiometric units provide physical counterparts without visual weighting. Radiant flux, the total power emitted as electromagnetic radiation, uses the watt (W), a derived unit from mechanics equivalent to kg ⋅ m² ⋅ s⁻³. Irradiance, the radiant flux per unit area on a surface, is thus W/m². The watt's origin in mechanical power underscores radiometry's foundation in energy transfer, distinct from photometry's perceptual basis.[4][23] The link between these domains is luminous efficacy, denoted $ K $, which converts radiant flux $ \Phi_e $ (in W) to luminous flux $ \Phi_v $ (in lm):
K=ΦvΦe K = \frac{\Phi_v}{\Phi_e}
with units lm/W. This ratio quantifies how effectively a source produces visible light from radiant power, derived by applying spectral luminous efficiency functions to the source's spectrum and scaling by the maximum efficacy constant. The candela was redefined in the 2019 SI revision, effective 20 May 2019, by fixing the luminous efficacy of monochromatic radiation at exactly 540 THz (corresponding to 555.017 nm wavelength) to 683 lm/W. Specifically, the candela is now the luminous intensity, in a given direction, of a source that emits monochromatic radiation at that frequency with radiant intensity of 1/683 W/sr. This anchors photometry directly to fundamental constants, enhancing traceability and stability.[4][23][24] Post-2019, this redefinition facilitates tighter integration of radiometry and photometry for modern applications, particularly LEDs and lasers, whose narrowband spectra align closely with the fixed efficacy point. Realizations now employ detector-based methods like cryogenic radiometers or photon-counting techniques to calibrate these sources, improving accuracy in spectral power measurements and luminous output for energy-efficient lighting and precision optics. For instance, LED characterizations use the fixed $ K_{cd} $ with spectral weighting to derive photometric quantities from radiometric data, supporting advancements in solid-state lighting standards.[24]

Supplementary and Related Units

Supplementary Units

In the International System of Units (SI), supplementary units historically referred to a distinct class of units introduced to address quantities like angles that did not fit neatly into the base or derived categories. The only two units in this class were the radian (rad), the coherent SI unit for plane angle, and the steradian (sr), the coherent SI unit for solid angle. The radian is defined as the plane angle subtended at the center of a circle by an arc whose length is equal to the radius of the circle, while the steradian is defined as the solid angle subtended at the center of a sphere by a portion of the surface whose area is equal to the square of the radius of the sphere.[4] These units were established by the 11th Conférence Générale des Poids et Mesures (CGPM) in 1960 as supplementary units, separate from the seven base units and the derived units, due to uncertainty about their dimensional status.[3] The classification of radian and steradian as supplementary units persisted until 1995, when the 20th CGPM adopted Resolution 8, which eliminated the supplementary category entirely and reclassified these units as dimensionless derived units with a dimension of one ([L⁰]). This decision affirmed the interpretation by the International Committee for Weights and Measures (CIPM) in 1980 that supplementary units should be regarded as dimensionless, resolving earlier debates about whether angles possessed independent dimensions.[25][26] For historical and practical reasons, the radian and steradian are still expressed using their special names and symbols rather than simply "1," though they are fundamentally ratios: the radian as a ratio of two lengths (m/m), and the steradian as a ratio of an area to the square of a length (m²/m²). This dimensionless nature is illustrated in the formula for arc length, where the arc length ss equals the radius rr times the plane angle θ\theta in radians:
s=rθ s = r \theta
Dimensionally, this yields meters (m) = m × (dimensionless), confirming that the radian cancels out without introducing new dimensions.[4] The radian and steradian play essential roles in derived SI units involving angular measures. For instance, angular velocity is expressed in radians per second (rad/s), quantifying rotational speed in mechanics. In photometry, the steradian appears in the definition of the lumen (lm), the unit of luminous flux, as lm = cd ⋅ sr, where cd is the candela; this extends to illuminance in lux (lx = cd ⋅ sr / m²). These applications highlight how the supplementary units, now integrated as derived, facilitate coherent expressions across physics without altering the SI's dimensional framework.[4]

Non-SI Units Commonly Used with SI

Although the SI is a coherent system based on seven base units, certain non-SI units are accepted for use alongside SI units owing to their entrenched practical value in science, engineering, commerce, and daily life. These units are precisely defined in terms of SI units to ensure interoperability, and their acceptance is governed by resolutions of the General Conference on Weights and Measures (CGPM) and recommendations of the International Committee for Weights and Measures (CIPM). The BIPM maintains an official list, updated periodically, which prioritizes units that facilitate communication without undermining the SI framework.[4] Key categories encompass units for time, plane angle, volume, pressure, and energy. For time, the minute, hour, and day remain indispensable for scheduling and historical records, converting directly as multiples of the second. The degree provides intuitive expression for angular measurements in navigation, surveying, and mathematics, equivalent to a fraction of the radian. The litre serves as a convenient measure for liquids in chemistry, medicine, and trade, aligning exactly with the cubic decimetre. In pressure, the bar offers a round value close to standard atmospheric pressure, aiding engineering and meteorology. The electronvolt quantifies subatomic energies succinctly in particle physics and quantum mechanics, where SI joules would yield impractically small numbers. In addition, specialized units for navigation such as the nautical mile and knot persist in maritime and aviation standards for their historical ties to Earth's geometry, though not officially accepted and with the BIPM advocating gradual replacement with SI equivalents like the metre and metre per second to enhance global uniformity.[4] The table below summarizes selected non-SI units accepted for use with the SI, including exact conversion factors:
CategoryUnitSymbolConversion to SI Units
Timeminutemin1 min = 60 s
Timehourh1 h = 3600 s
Timedayd1 d = 86 400 s
Angledegree°1° = π\pi/180 rad
VolumelitreL1 L = 1 dm³ = 10−3^{-3} m³
Pressurebarbar1 bar = 105^5 Pa
EnergyelectronvolteV1 eV = 1.602 × 10−19^{-19} J
These definitions stem from international agreements ensuring exactness, with SI prefixes applicable to some (e.g., keV, mL) but not time units.[4] The acceptance of these units traces to the establishment of the SI at the 11th CGPM in 1960, where Resolution 12 formalized the system but permitted transitional non-coherent units; subsequent decisions, including those at the 12th CGPM in 1964, endorsed specific ones like the litre for ongoing use. This tolerance reflects a balance between coherence and pragmatism, allowing fields like particle physics to leverage the electronvolt's scale without reformulating established equations, while urging adoption of pure SI units over time.[3]
User Avatar
No comments yet.