Hubbry Logo
Deuterium arc lampDeuterium arc lampMain
Open search
Deuterium arc lamp
Community hub
Deuterium arc lamp
logo
8 pages, 0 posts
0 subscribers
Be the first to start a discussion here.
Be the first to start a discussion here.
Deuterium arc lamp
Deuterium arc lamp
Deuterium arc lamp
View on Wikipedia
from Wikipedia
Deuterium arc lamp

A deuterium arc lamp (or simply deuterium lamp) is a low-pressure gas-discharge light source often used in spectroscopy when a continuous spectrum in the ultraviolet region is needed.

Plasma "arc" or discharge lamps using hydrogen are notable for their high output in the ultraviolet, with comparatively little output in the visible and infrared. This is similar to the situation in a hydrogen flame. Arc lamps made with ordinary light-hydrogen (hydrogen-1) provide a very similar UV spectrum to deuterium, and have been used in UV spectroscopes. However, lamps using deuterium have a longer life span and an emissivity (intensity) at the far end of their UV range which is three to five times that of an ordinary hydrogen arc bulb, at the same temperature. Deuterium arc lamps, therefore, despite being several times more expensive, are considered a superior light source to light-hydrogen arc lamps, for the shortwave UV range.

Principle of operation

[edit]
Emission spectrum of an ultraviolet deuterium arc lamp showing characteristic hydrogen Balmer lines (sharp peaks at 486 nm and 656 nm labeled Dβ and Dα from left to right respectively), continuum emission in the ~160-400 nm region and Fulcher band emission between around 560 to 640 nm. The emission spectrum of deuterium differs slightly from that of protium (hydrogen-1) due to the influence of hyperfine interactions, though these effects alter the wavelength of the lines by mere fractions of a nanometer and are too fine to be discerned by the spectrometer used here. Deuterium is used rather than normal hydrogen because of its greater intensity of UV emission in the molecular band.

A deuterium lamp uses a tungsten filament and anode placed on opposite sides of a nickel box structure designed to produce the best output spectrum. Unlike an incandescent bulb, the filament is not the source of light in deuterium lamps. Instead, an arc is created from the filament to the anode, a similar process to arc lamps. Since the filament must be very hot before it can operate, it is heated for approximately 20 seconds before use. Since the discharge process produces its own heat, the heater is turned down after discharge begins. Although firing voltages are 300 to 500 volts, once the arc is created, voltages drop to around 100 to 200 volts.[1]

The arc created excites the molecular deuterium contained within the bulb to a higher energy state. The deuterium then emits light as it transitions back to its initial state. This continuous cycle is the origin of the continuous UV radiation. This process is not the same as the process of decay of atomic excited states (atomic emission), where electrons are excited and then emit radiation. Instead, a molecular emission process, where radiative decay of excited states in molecular deuterium (D2 or 2H2), causes the effect.

The spectral line structure of deuterium does not differ noticeably from that of light hydrogen, but deuterium has a slightly stronger molecular bond (439.5 vs. 432 kJ/mol) and is less-well ionized at the temperature of the arc. This causes a larger population of molecules and a greater emissivity (light output) of UV in the molecular part of the spectrum that is furthest into the ultraviolet.[2]

Since the lamp operates at high temperatures, normal glass housings cannot be used for a casing. They would also block UV radiation. Instead, a fused quartz, UV glass, or magnesium fluoride envelope is used depending on the specific function of the lamp.[3]

The typical lifetime of a deuterium lamp is approximately 2,000 hours (Most manufacturers guarantee 2,000 hours, but newer lamps are consistently performing well at 5,000 hours and more).[citation needed]

Deuterium lamp spectra

[edit]

The deuterium lamp emits radiation extending from 112 nm to 900 nm, though its continuous spectrum is only from 180 nm to 370 nm. The spectrum intensity does not actually decrease from 250 nm to 200 nm as shown in the spectrum plot above. The decrease in the plot is due to decreased efficiency at low wavelengths of the photo detector used to measure the lamp intensity. The deuterium lamp's continuous spectrum is useful as both a reference in UV radiometric work and to generate a signal in various photometric devices.

Safety

[edit]

Due to the high intensity of UV radiation emitted by the bulb, eye protection is suggested when using a deuterium bulb. Care must also be taken to not touch the bulb directly to avoid burns due to high operating temperatures. Touching the bulb directly even when cool could deposit impurities onto the casing that strongly absorb the short wavelength UV and therefore reduce output intensity.

References

[edit]
Revisions and contributorsEdit on WikipediaRead on Wikipedia

Deuterium arc lamp

View on Grokipedia
from Grokipedia
A deuterium arc lamp is a low-pressure gas-discharge light source that operates by generating an electrical arc discharge between electrodes in a chamber filled with (D₂) gas, producing a continuous and intense spectrum primarily in the (UV) region. Developed in the mid-20th century as an improvement over arc lamps for UV , this design yields a stable, line-free continuum emission, with spectral output ranging from 160 nm to 400 nm when using synthetic silica windows, or extending to 115 nm with (MgF₂) windows, and peaking around 190 nm in radiant power. The lamp's brightness is enhanced by a small (typically 0.5 mm or 1.0 mm diameter) in the electrode assembly, and it maintains low output fluctuations of about 0.005% peak-to-peak, with lifetimes up to 2000–4000 hours depending on the model. Deuterium arc lamps are prized for their favorable ratio of UV to visible light intensity compared to hydrogen arc lamps, making them superior for deep-UV applications while minimizing interference from longer wavelengths. They function as transfer standards for spectral irradiance in the UV, calibrated against primary sources like or blackbody standards, with high reproducibility that supports interlaboratory comparisons across 167–350 nm. Operating at input powers of 20–50 W DC, these lamps are often paired with tungsten-halogen lamps in dual-beam spectrophotometers to cover the full UV-Vis range (185–800 nm). Deuterium arc lamps are widely used in analytical , including UV-Vis absorption and fluorescence spectrophotometry, (HPLC) detectors, , and inspection. They also serve as calibrated standards in vacuum UV research for fields like and .

Overview

Definition and Characteristics

A deuterium arc lamp is a low-pressure gas-discharge light source that utilizes an electrical arc in (D₂) gas to generate continuous (UV) radiation, primarily employed in spectroscopic applications. Key characteristics include high-intensity UV output extending down to 160 nm, a compact arc size of approximately 1 mm in diameter, typical electrical power consumption of 20-30 , and an operational lifetime ranging from 1,000 to 2,000 hours, with advanced models achieving up to 4,000 hours. Visible and emissions are negligible, ensuring a focused UV suitable for precise analytical work. Compared to arc lamps, lamps provide a broader and more intense UV continuum, along with superior output stability essential for accurate measurements. They exhibit negligible emission beyond 400 nm, minimizing interference in UV-specific applications. In general performance, these lamps operate at 100-200 V after arc striking and draw currents of 300-850 mA, delivering a continuous UV from 160 nm to 400 nm where stable, high-intensity illumination is required.

Historical Development

The development of the deuterium arc lamp traces its origins to the broader evolution of technology in the . In 1807, British chemist demonstrated the first practical electric light source by creating an arc between two carbon electrodes connected to a large battery, producing a brilliant glow from charcoal sticks that marked the inception of arc lighting. This carbon arc lamp laid the foundational principles for subsequent electric illumination devices, though it was initially limited by the need for cumbersome power sources and frequent electrode maintenance. The technology advanced toward practicality in 1876 when Russian engineer Pavel Yablochkov invented the "Yablochkov candle," a self-consuming carbon arc lamp that eliminated the need for mechanical electrode adjustment, enabling its deployment in public lighting applications such as street lamps in . The transition from solid-electrode arc lamps to gas-discharge variants occurred in the early , driven by the exploration of low-pressure gas plasmas for more stable and efficient light emission. Early gas-discharge experiments, building on arc principles, included the development of mercury vapor lamps around , which introduced controlled electrical discharges in gaseous media to produce and visible light. arc lamps specifically emerged in the 1950s as specialized sources for spectroscopy, motivated by the growing need for reliable UV continuum radiation in . These lamps replaced earlier arc sources due to deuterium's superior UV —approximately three to five times higher in the far-UV range—resulting from isotopic effects that reduce molecular band interferences and absorption, along with reduced spectral impurities, enabling higher precision in absorbance measurements. Following , deuterium arc lamps saw rapid commercialization in the , coinciding with the proliferation of UV-visible spectrophotometers in research and industry. This adoption was propelled by the demand for stable, continuous UV sources to support quantitative analysis in fields like biochemistry and pharmaceuticals. By the mid-, advancements in vacuum technology and materials had made deuterium lamps a standard component in analytical setups, facilitating the boom in spectroscopic applications during that decade. In the 2020s, the deuterium arc lamp market has experienced steady growth, projected to reach approximately USD 240 million by 2031, fueled by expansions in for and life sciences. Recent innovations include enhanced stability models, such as Avantes' integration of deuterium sources into compact spectrometer bundles for real-time UV analysis, and ' July 2023 launch of next-generation lamps with improved output consistency. These developments emphasize refined designs, such as optimized structures, which extend operational lifetimes beyond 2,000 hours while minimizing degradation in UV intensity.

Design and Construction

Key Components

The deuterium arc lamp features a compact internal structure designed to facilitate the generation of light through a controlled electrical discharge. At its core are the s and enclosure that house the arc, along with sealing and connection elements that ensure reliable operation and light output. The serves as the electron-emitting electrode and is usually constructed from a filament coated with a triple oxide layer of , , and calcium to enhance . This design allows the to be preheated for initiating the discharge while minimizing material degradation over time. In some configurations, it incorporates a covering to prevent irregular discharges and is positioned offset from the for optimal light directionality. The , which collects electrons to maintain the arc, is typically made of in a plate or rod form, often shielded within the lamp's . Like the , it may feature a coating to suppress abnormal electrical activity and includes an to direct emitted toward the output . The containment structure is a high-purity box that encloses the electrodes and defines the arc gap, typically measuring 0.5 to 2.5 to confine the discharge effectively. This box minimizes impurities that could interfere with the light spectrum and maintains the low-pressure environment necessary for the arc. The entire assembly is sealed within a envelope to protect the components and allow transmission of radiation. The output window, which seals the lamp envelope and transmits the generated light, is commonly made of (synthetic silica) for transmission down to approximately 160 nm, or (MgF₂) for extended vacuum ultraviolet access starting at 115 nm. These materials ensure high optical clarity while withstanding the internal thermal and electrical stresses. Electrical connections are provided via a base, such as a three-pin pinch seal or a 7/9-pin molded configuration, which offers mechanical support and secure attachment to power supplies. Optional external housings may include integrated lenses to focus the beam for specific applications. The gas fill consists of pure (D₂) at low pressure, with initial fill typically around 7.5 (corresponding to an optimal operating pressure of about 4.5 for peak UV output), and purity typically exceeding 99.7%. This fill occupies the arc gap within the nickel enclosure, enabling the discharge while avoiding spectral contamination.

Materials and Manufacturing

Deuterium arc lamps employ carefully selected electrode materials to ensure durability under high-temperature arc conditions. The cathode is typically constructed from tungsten, which has a high melting point of approximately 3,422°C and excellent resistance to sputtering, allowing it to withstand the erosive effects of the plasma discharge without rapid degradation. In contrast, the anode and surrounding box structure are made from nickel, chosen for its low vapor pressure that minimizes contamination of the discharge plasma by metal vapors, thereby preserving spectral purity. The anode itself is typically molybdenum or tungsten. The lamp envelope and output window materials are optimized for ultraviolet transmission while maintaining structural integrity. Fused silica, also known as , serves as the primary envelope material, offering high transparency in the 200-400 nm range and resistance to thermal and photochemical stress. For applications requiring deeper penetration below 200 nm, (MgF₂) windows are used, transmitting down to approximately 115 nm; however, MgF₂ is hygroscopic, necessitating protective handling and sealing to prevent moisture-induced degradation. High-purity gas, typically exceeding 99.7% (up to 99.99% in some models), fills the lamp to produce a smooth continuum spectrum free from interfering emission lines, with manufacturing processes conducted under conditions to exclude impurities like oxygen or residual . Fabrication begins with sealing of the structure within the envelope, followed by precise alignment to within ±0.1 mm to ensure stable arc positioning and optimal light output. The assembly undergoes annealing to relieve internal stresses in the silica components, enhancing long-term reliability, and rigorous testing for leaks and output consistency verifies performance before deployment. Modern variations incorporate ceramic coatings on the to further extend operational life by suppressing abnormal discharges and reducing electrode wear. Additionally, modular designs facilitate easy integration and replacement within analytical instruments, contributing to overall system maintainability without compromising material integrity. These material choices and fabrication methods directly influence lamp lifetime, often exceeding 1,000 hours under standard conditions.

Principle of Operation

Arc Initiation and Sustainment

The arc initiation in a deuterium lamp begins with preheating the filament to enable thermionic emission. The consists of a wire coated with emissive materials, such as a triple carbonate layer of , , and calcium, which lowers the required emission temperature to approximately 900–2000°C. This heating is accomplished by applying a filament voltage of 2–12 V, drawing currents up to 6 A, for a warm-up period of 30–90 seconds to ensure stable release into the low-pressure environment. Following cathode preheating, a high-voltage pulse of 250–600 V DC is applied across the electrodes, separated by a narrow gap of about 1 mm, to ionize the gas filled at 1–15 . The , often lasting around 10 µs with a transient current of 15 mA, triggers gas breakdown and plasma formation, rapidly establishing the arc discharge as electrons and ionize surrounding molecules. Once initiated, the arc sustainment relies on reducing the voltage to an operating level of 65–100 V while maintaining a of 300–850 mA through a , typically delivering 20–30 W total input. A ballast or current-limiting circuit prevents voltage fluctuations and arc instability by compensating for variations in lamp impedance. The discharge is confined to the small gap by the structure, often featuring a or enclosure that promotes uniform plasma localization and heat management. Key factors influencing arc stability include precise control of gas at 0.5–5 to optimize without excessive erosion, and careful spacing to balance dissipation and prevent arc wandering. Optimal bulb wall temperatures of 245–290°C further ensure consistent gas and minimal output drift, with stability achieving fluctuations as low as 0.005% peak-to-peak.

Light Emission Process

In a deuterium arc lamp, the light emission process begins with the excitation of gas within the plasma formed by the arc discharge. High-energy electrons, typically possessing energies of 10 to 20 eV, collide with D₂ molecules, causing dissociation into deuterium atoms while simultaneously exciting these atoms (and residual molecules) to higher electronic states. This excitation is facilitated by the low-pressure environment, where electron-impact processes dominate energy transfer in the plasma. The excited deuterium atoms and ions subsequently de-excite, releasing photons through radiative transitions and recombination with electrons. For discrete line emissions, the photon energy follows the adapted for hydrogen-like deuterium atoms: E=hν=13.6 eV(1n12−1n22)E = h\nu = 13.6 \, \text{eV} \left( \frac{1}{n_1^2} - \frac{1}{n_2^2} \right) where n1n_1 and n2n_2 are the principal quantum numbers of the initial and final states (n2>n1n_2 > n_1). However, the spectrum is predominantly continuous due to broadening effects in the dense plasma, arising from free-free and bound-free processes. The high-temperature plasma promotes efficient emission by populating high-energy states while the design suppresses longer-wavelength visible and output relative to the UV continuum. This ensures a high radiant power ratio in the UV, making the lamp suitable for applications.

Spectral Output

Wavelength Range

The deuterium arc lamp generates a continuous , with the primary operational range spanning 160 nm to 400 nm in standard configurations equipped with synthetic silica windows. This coverage provides high-intensity output particularly between 180 nm and 370 nm, making it suitable for applications. The lower wavelength limit is set at approximately 160 nm by the transmission properties of the synthetic silica window material, while specialized models using (MgF₂) windows extend this cutoff to around 115 nm for vacuum ultraviolet use. At the upper end, the spectrum tapers due to the excitation characteristics of , resulting in negligible emission beyond 400 nm despite theoretical extension up to 900 nm. The emission profile consists of a broad continuum arising primarily from molecular deuterium emission bands, overlaid with weak atomic lines, including features such as those at 486 nm and 656 nm. is favored over as the fill gas because it delivers higher intensity while producing fewer interfering spectral lines, enhancing the smoothness of the continuum. Variations exist across lamp designs, with space-qualified models offering broader coverage from 112 nm to approximately 370 nm to accommodate extended environmental requirements in applications.

Intensity and Stability

Deuterium arc lamps exhibit high intensity in the region, with peak near 200 nm. This radiance decreases toward the spectral edges, for example, reaching approximately 50% of the peak value at 160 nm due to reduced emission efficiency at shorter wavelengths. The total ultraviolet radiant power typically ranges from 1 to 5 W, depending on the lamp's electrical input power (commonly 30 W) and design efficiency. The intensity distribution forms a relatively flat continuum across the 200-350 nm range, providing consistent output suitable for broad-spectrum applications. Below 250 nm, the intensity drops owing to inherent molecular emission characteristics of the discharge, independent of detector limitations. Stability is a key attribute, with short-term output fluctuations typically below 0.5% peak-to-peak over intervals of 100 ms, enabling precise measurements in analytical settings. Achieving 1% long-term stability requires a warm-up period of 20-30 minutes to reach . Over the lamp's operational lifetime, output degrades gradually, reaching 50% of initial value after approximately 2000 hours (equivalent to about 2.5% per 100 hours). Calibration standards for irradiance in the 200-400 nm range have uncertainties of 1.8-5.3%.

Applications

Analytical Spectroscopy

Deuterium arc lamps are widely employed as stable light sources in UV-Vis , providing continuous emission from approximately 190 to 400 nm ideal for measuring and of samples. These lamps deliver high-intensity continuum radiation in the UV region, enabling precise quantification of molecular transitions in organic and inorganic compounds. To extend coverage into the visible spectrum, deuterium lamps are typically paired with a tungsten-halogen source, with automatic switching around 350 nm to maintain spectral continuity across 190-800 nm. In , particularly (HPLC) and (GC), deuterium arc lamps power UV absorption detectors for identifying and quantifying analytes based on their UV absorbance profiles. The lamps' broad UV output from 160-400 nm supports detection of aromatic compounds and conjugated systems in pharmaceutical formulations, such as non-steroidal anti-inflammatory drugs. This application benefits from the lamps' long operational life, often exceeding 2000 hours, ensuring consistent sensitivity for trace-level analysis. For atomic absorption and emission spectroscopy, deuterium arc lamps function as continuum sources for background correction, facilitating accurate detection of trace elements in environmental samples like and . By emitting UV , they compensate for non-specific absorption from matrices, improving signal-to-noise ratios in or graphite furnace atomizers. This role is critical for regulatory monitoring of at parts-per-billion levels. Deuterium lamps also serve as excitation sources in fluorimetry and electrophoresis techniques, where their UV output excites fluorescent tags on biomolecules for separation and quantification. In capillary electrophoresis, for instance, the 185-400 nm emission enables detection of DNA fragments and proteins via native or labeled fluorescence, supporting genomics and proteomics research. Similarly, in fluorimeters, the lamps provide versatile excitation for low-concentration analytes, enhancing sensitivity in biochemical assays. A specialized application involves and gas analyzers, where deuterium arc lamps in the 200-300 nm range enable non-dispersive UV absorption measurements for monitoring sulfur and emissions in industrial exhausts. This setup allows real-time quantification of pollutants at compliance levels, aiding efforts.

Industrial and Scientific Uses

Deuterium arc lamps are used in manufacturing for calibrating broadband UV meters that measure total exposure to UV radiation, ensuring uniformity across wafers during fabrication. For , portable analyzers equipped with deuterium arc lamps enable real-time detection of air and pollutants, such as , by leveraging UV in compact devices suitable for field deployment. These lamps emit strong UV radiation at wavelengths absorbed by (around 254 nm), allowing quantification of trace concentrations in ambient samples with high sensitivity. Such systems are used in testing and on-site assessments, contributing to control efforts. In scientific , deuterium arc lamps act as transfer standards for synchrotron radiation sources in the UV range, providing a stable reference from 200 to 400 nm to validate performance and ensure accurate spectral measurements. They are also employed in space instruments for UV astronomy, such as NASA's Solar Ultraviolet Spectral Monitor (SUSIM) on the Upper Atmosphere Research Satellite, where onboard deuterium lamps maintain of solar UV observations over mission lifetimes. These applications underscore the lamps' role in high-precision astrophysical . Emerging applications from 2020 to 2025 include the use of deuterium arc lamps in UV systems for material differentiation, where their intense UV emission (225-408 nm) enhances spectral contrast in non-destructive analysis of surfaces like raw varieties, aiding in and . As of 2025, emerging trends include and integration into automated systems, improving stability for applications.

Safety and Handling

Radiation and Electrical Hazards

Deuterium arc lamps produce intense ultraviolet C (UVC) radiation in the wavelength range of approximately 100-280 nm, primarily from the arc discharge in deuterium gas. This UVC output can cause acute eye damage, including photokeratitis—a painful inflammation of the cornea resembling a sunburn—and conjunctivitis, with symptoms such as blurred vision and tearing appearing hours after exposure. Prolonged or repeated exposure to this radiation also contributes to the development of cataracts by damaging the lens of the eye. On the skin, UVC radiation induces erythema (reddening) and severe burns even with brief exposure, while chronic exposure elevates the risk of skin cancer due to DNA damage in skin cells. Exposure levels exceeding 6 mJ/cm² for the eyes or 10 mJ/cm² for the skin (at 254 nm) are considered hazardous for unprotected exposure, potentially leading to immediate injury. The National Institute for Occupational Safety and Health (NIOSH) recommends limiting UVC exposure to an average irradiance of less than 0.2 µW/cm² over an 8-hour period to prevent adverse health effects. Operation of deuterium arc lamps involves high-voltage electrical systems, with striking voltages typically ranging from 300 to 500 V to initiate the arc discharge, posing a significant risk of electrical shock that can result in severe or . The arc plasma reaches very high temperatures, and if the lamp envelope breaks during operation, it can lead to thermal burns from the hot plasma or an explosive release of energy. The deuterium gas fill within the lamp is highly flammable and forms explosive mixtures with air over a wide concentration range of 4% to 75% by volume, creating a or hazard if the lamp ruptures and releases the gas. Overheating can cause pressure buildup inside the sealed envelope, potentially leading to rupture and the violent expulsion of contents. Common failure modes include bulb rupture or , which shatters the or fused silica envelope and releases hot glass fragments capable of causing lacerations and burns. Additionally, the UVC radiation interacts with atmospheric oxygen to generate , a toxic gas that irritates the and lungs even at low concentrations, exacerbating exposure risks in enclosed spaces.

Operational Precautions

Operators of deuterium arc lamps must employ appropriate to mitigate risks from radiation and high temperatures. UV-blocking or face shields with transmittance less than 1% at 200 nm are essential to protect the eyes from deep UV exposure, while gloves and full-body coverage prevent skin contact with harmful rays or hot surfaces. Direct viewing of the lamp without protection is strictly prohibited. Lamps should be operated within shielded housings equipped with interlocks to prevent accidental exposure during use. Adequate ventilation is required to disperse generated by wavelengths below 240 nm, maintaining levels below 0.1 ppm for prolonged exposure. Electrical safety protocols include using grounded power supplies to minimize shock hazards from the high voltages (typically 300-700 V) required for arc initiation and sustainment. After operation, allow at least 20-30 minutes for cooldown before handling to avoid burns from surfaces exceeding 200°C. Fingerprints on the quartz window must be avoided, as they can absorb UV light and reduce output by up to 20% through localized heating and deposition. Maintenance involves regular monitoring of light output, with replacement recommended when intensity at 230 nm drops to 50% of initial value to ensure performance stability. Clean windows with alcohol or acetone using lint-free cloth before installation, and store lamps in a dry environment with low humidity, ideally in an inert atmosphere to prevent degradation. Disposal must follow local regulations for , accounting for gas and metallic components like and ; lamps should not be broken casually but handled by licensed services. Users should receive training aligned with IEC 62471 (including Part 6:2022 for lamps) standards for photobiological , including the use of UV meters to monitor exposure levels and ensure compliance with risk group classifications for the lamp system.

References

  1. https://www.nist.gov/document/ao17-4pdf
  2. https://www.hamamatsu.com/content/dam/hamamatsu-photonics/sites/documents/99_SALES_LIBRARY/etd/D2lamps_TLS1017E.pdf
  3. https://opg.optica.org/abstract.cfm?uri=ao-17-4-593
  4. https://www.agilent.com/cs/library/primers/public/primer-uv-vis-basics-5980-1397en-agilent.pdf
  5. https://pmc.ncbi.nlm.nih.gov/articles/PMC11677917/
  6. https://tec5usa.com/product/deuterium-lamp/
  7. https://www.newport.com/f/deuterium-lamps
  8. https://www.newport.com/p/63162
  9. https://www.newport.com/f/deuterium-lamp-power-supplies
  10. https://makezine.com/projects/humphry-davy-and-the-arc-light/
  11. https://ceramics.org/ceramic-tech-today/yablochkov-candles-history-in-paris/
  12. https://www.optica-opn.org/home/articles/volume_19/issue_9/features/a_brief_history_of_lighting/
  13. https://www.irisotope.com/en/blog/59/deuterium-lamps
  14. https://www.labmanager.com/evolution-of-uv-vis-spectrophotometers-18481
  15. https://pmc.ncbi.nlm.nih.gov/articles/PMC12003936/
  16. https://www.marketmonitorglobal.com/reports/1814444/uv-deuterium-lamp-source
  17. https://avantesusa.com/wp-content/uploads/2022/04/Brochure-Life-Sciences-Configurations.pdf
  18. https://www.databridgemarketresearch.com/reports/global-deuterium-lamps-market
  19. https://www.hamamatsu.com/us/en/product/light-and-radiation-sources/lamp/deuterium-lamp.html
  20. http://www.alphalight.co.kr/web_data/down/Deuterium_Cathodeon.pdf
  21. https://patents.google.com/patent/US4016445A/en
  22. https://www.plansee.com/en/products/tungsten-electrodes-for-discharge-lamps.html
  23. https://mcphersoninc.com/lightsources/model632.html
  24. https://ridl.cfd.rit.edu/products/manuals/Hamamatsu/deuterium.pdf
  25. https://www.thorlabs.com/newgrouppage9.cfm?objectgroup_id=11783
  26. https://www.alphalight.co.kr/web_data/down/Deuterium_Cathodeon.pdf
  27. https://www.energetiq.com/ldls-sheds-light-on-analytical-sciences-applications
  28. https://opg.optica.org/ao/abstract.cfm?uri=ao-17-4-593
  29. https://www.newport.com/f/series-q-deuterium-light-sources
  30. https://pubmed.ncbi.nlm.nih.gov/32976440/
  31. https://personal.utdallas.edu/~goeckner/plasma_tech_class/AgilentSpectroPub4.pdf
  32. https://research.njit.edu/york/uv-visible-spectrophotometer
  33. http://www.civil.northwestern.edu/EHE/COURSES/eac/exp2/meth2.htm
  34. https://www.noblelight.com/en/etc/industries_and_applications/optical_analysis/lamps_for_high_performance_liquid_chromatography_hplc.html
  35. https://www.thermofisher.com/order/catalog/product/6074.1110
  36. https://www.labcompare.com/10-Featured-Articles/358156-Considerations-for-Replacing-Deuterium-Lamps-in-HPLC-Systems/
  37. https://www.agilent.com/en/product/atomic-spectroscopy/atomic-absorption/atomic-absorption-background-correction-lamps/deuterium-lamps
  38. https://www.technologynetworks.com/analysis/articles/atomic-absorption-spectroscopy-principles-and-applications-356829
  39. https://chem.libretexts.org/Courses/Providence_College/CHM_331_Advanced_Analytical_Chemistry_1/10%253A_Molecular_Luminescence_Spectrometry/10.02%253A_Fluorescence_and_Phosphorescence_Instrumentation
  40. https://us-store.sciex.com/USD/capillary-electrophoresis/detectors-and-accessories/accessories/Deuterium-Lamp-185-nm-to-400-nm-with-Connector-zid5065163
  41. https://microbenotes.com/fluorimetry/
  42. https://www.jinsptech.com/news/what-is-a-deuterium-lamp-used-for/
  43. https://41j.com/blog/wp-content/uploads/2021/11/Lmps_L2D2.pdf
  44. https://tsapps.nist.gov/publication/get_pdf.cfm?pub_id=841518
  45. https://pubs.acs.org/doi/10.1021/acsmeasuresciau.1c00028
  46. https://www.epa.gov/sites/default/files/2020-01/documents/philadelpia.pdf
  47. https://www.nist.gov/programs-projects/comparison-synchrotron-radiation-based-ultraviolet-source-calibrations-ptb-and
  48. https://earth.gsfc.nasa.gov/climate/projects/solar-irradiance/instruments/susim
  49. https://www.mdpi.com/2313-433X/10/12/310
  50. https://www.marketreportanalytics.com/reports/deuterium-light-source-78916
  51. https://www.ccohs.ca/oshanswers/phys_agents/ultravioletradiation.html
  52. https://www.azooptics.com/Article.aspx?ArticleID=19
  53. https://www.cdc.gov/niosh/hhe/reports/pdfs/2007-0257-3082.pdf
  54. https://www.airgas.com/msds/001017.pdf
  55. https://cameochemicals.noaa.gov/chemical/3073
  56. https://www.newport.com/medias/sys_master/root/h46/h77/9330394365982/M60000.pdf
  57. https://www.newport.com/n/ultraviolet-safety-considerations
  58. https://solarcsystems.com/products/uv-eye-protection/
  59. https://www.agilent.com/cs/library/troubleshootingguide/public/technicaloverview-AA-guide-5994-0858EN-agilent.pdf
  60. https://www.ssi.shimadzu.com/sites/ssi.shimadzu.com/files/pim/pim_document_file/ssi/sds/25286/PSDS_062-65063-01_ENA.pdf
  61. https://webstore.iec.ch/en/publication/7076
  62. https://webstore.iec.ch/publication/68389
Add your contribution
Related Hubs
User Avatar
No comments yet.