Hubbry Logo
Face shieldFace shieldMain
Open search
Face shield
Community hub
Face shield
logo
8 pages, 0 posts
0 subscribers
Be the first to start a discussion here.
Be the first to start a discussion here.
Face shield
Face shield
Face shield
View on Wikipedia
from Wikipedia
A United States Navy Electrician's Mate wearing a face shield while checking for bad fuses on a lighting panel
Nurse using a face shield during the Ebola outbreak in Sierra Leone, 2014.

A face shield, an item of personal protective equipment, aims to protect the wearer's entire face (or part of it) from hazards such as flying objects and road debris, chemical splashes (in laboratories or in industry), or potentially infectious materials (in medical and laboratory environments).[1]

Applications

[edit]

Medical

[edit]
A laboratory technician wearing a face shield during the COVID-19 pandemic in Brazil
A video describing research on the efficacy of face shields to protect against aerosol emitted from coughing

In medical applications the device is used to protect a medical professional during a procedure that might expose them to blood or other potentially infectious fluids or aerosols. An example is the use of a CPR mask while performing rescue breathing or CPR. Another example is the use of face shields to reduce the likelihood of inhaling potentially infectious bioaerosols.[2]

See also: Shortages related to the COVID-19 pandemic § Medical face shield

Police and military

[edit]
  • Russian combat engineer with a 6B47 helmet and ballistic face shield
  • text
    Removing a face shield from a Sailor's MCU-2/P gas mask after washing it with decontamination solution during a General Quarters Drill aboard an aircraft carrier

In military or law enforcement environments, a face shield may be designed for ballistic or non-ballistic protection. The non-ballistic shield will provide no protection from projectiles shot from firearms,[3] but is usually designed to withstand low velocity impacts, like caused by punches or thrown objects.[4]

A ballistic face shield is designed to stop or deflect blast and fragments from operators wearing bomb suits[5] To protect the wearers eyes and face from ballistic threats in combat is envisioned in the PEO Soldier program for the United States Department of Defence.[6]

Construction

[edit]

A face shield is intended to protect the wearer's partial or entire face and the eyes from hazards. Face shields should be used with spectacles and/or goggles.[7] On many construction sites many workers use face shields to protect them from debris or sparks. Many tools for cutting and working with metal recommend the use of a face shield. Examples include welding equipment or metal chop saws.

Manufacturing

[edit]

Two methods are used to manufacture face shields: extrusion and injection molding. Face shields cut from extrusion sheets provide better impact resistance than injection-molded face shields because extrusion sheets are made of high molecular weight plastic pellets while injection molding must use lower molecular weight plastic pellets, which provide better melt flowing property needed by injection molding.

Face shields can be made of polycarbonate which provides excellent impact resistance, optical quality, heat resistance and normal chemical resistance. Or cellulose acetate which provides normal impact resistance, optical quality, heat resistance and good chemical resistance.

Face shields 0.8 mm (0.031 in) thick made of extrusion polycarbonate sheets can withstand the impact of a 6 mm (0.24 in) nominal diameter steel ball traveling at the speed 120 m/s (390 ft/s) (European standard, protection against high-speed particles – medium energy impact), while injection molding face shields must have at least 1.5 mm (0.059 in) thickness to withstand the same impact. But injection molding can provide more complicated shape than extrusion.

During the COVID-19 pandemic, people from 86 countries engaged in the voluntary production of PPE to supplement traditional supply chains - many of which had been interrupted.[8] They collectively produced a total of 25 million face shields with techniques including 3D printing and laser cutting, in addition to injection molding.

  • 3D printing of face shields during COVID-19 pandemic
    3D printing of face shields during COVID-19 pandemic
  • 3D file for printing a face shield[9]
    3D file for printing a face shield[9]
  • Buckle for the face shield
    Buckle for the face shield
  • Final shield
    Final shield

Standards

[edit]
ANSI (American Standard)
  • Mark Z87: Basic impact: Faceshields shall be capable of resisting impact from a 25.4 mm (1 in) diameter steel ball dropped from a height of 127 cm (50 in).
  • Mark Z87+: High impact: Faceshields shall be capable of resisting impact from a 6.35 mm (0.25 in) diameter steel ball traveling at a velocity of 91.4 m/s (300 ft/s). 
EN 166 (European Standard)

These shields are for protection against high-speed particles, and must withstand the impact of a 6 mm nominal diameter steel ball, striking the oculars and the lateral protection at the speed stated.

  • Mark A: 190 m/s (620 ft/s)
  • Mark B: 120 m/s (390 ft/s).
  • Mark F: 45 m/s (150 ft/s).
    • ref. EN166
CSA (Canadian Standard)

Z94.3-15 Eye and Face Protectors Class 6 relates to face shields, and is divided into 3 sub-classes

  • 6A – Impact, piercing, splash, head, and glare protection.
  • 6B – Radiation protection. Also for low heat, splash, glare, and light non-piercing impact protection.
  • 6C – High-heat applications and light non-piercing impact protection only.
    • ref. CSA Z94.3-15

See also

[edit]

References

[edit]
[edit]
Revisions and contributorsEdit on WikipediaRead on Wikipedia

Face shield

View on Grokipedia
from Grokipedia
A face shield is a type of (PPE) comprising a transparent affixed to a , , or frame, intended to shield the wearer's face—including eyes, , and —from hazards such as splashes, sprays, flying particles, and chemical irritants. Face shields provide barrier protection for the facial area and associated mucous membranes but are classified as secondary PPE, requiring primary like safety glasses underneath to address gaps in coverage. They are employed across sectors including , , work, and healthcare to mitigate risks from mechanical impacts, biological fluids, and environmental contaminants. In infection control contexts, face shields reduce short-term exposure to large droplets from coughs or splatters, as demonstrated in controlled experiments where they blocked substantial portions of simulated infectious particles. However, their efficacy diminishes over time due to leakage around the bottom and sides, rendering them inadequate as standalone respiratory barriers against fine airborne pathogens, with studies showing inferior performance to or respirators for source control and sustained filtration.

Definition and Design

Core Components and Functionality

Face shields consist of three primary components: a transparent , a supportive frame or , and a suspension or attachment system. The , typically constructed from impact-resistant or similar polymers, forms the main protective barrier extending across the to below the , providing full facial coverage. The frame, often made of adjustable or metal, secures the and includes a or straps that wrap around the head for stability. Suspension elements, such as foam padding or ratchet mechanisms, enhance wearer comfort and allow for size adjustments to accommodate various head shapes. These components function together to create a physical barrier shielding the face, eyes, nose, and mouth from hazards including flying debris, chemical splashes, and large infectious droplets. Unlike , face shields permit and do not press against the face, reducing discomfort during extended use, though they may require pairing with spectacles for complete eye sealing against smaller particles. Compliance with ANSI/ISEA Z87.1 standards ensures the shield withstands specified impact levels, with markings indicating protection type, such as basic (Z87) or high-velocity impact resistance. Functionality extends to mitigating splash and spray exposure in industrial, , and settings, where the curved or flat design deflects projectiles away from the user. coatings on visors address issues from or breath, preserving , while anti-scratch treatments prolong against abrasions. However, face shields alone do not filter airborne contaminants like aerosols, necessitating integration with respirators for comprehensive respiratory protection.

Variations and Types

Face shields exhibit variations primarily in visor coverage, attachment mechanisms, material treatments, and integrated features to address diverse hazards such as impacts, splashes, and . Full-coverage designs, extending from the to the and often 8-10 inches in width, provide comprehensive barrier protection to the face, eyes, , and mucous membranes, as required for high-risk exposures under ANSI/ISEA Z87.1-2020 standards for and impact resistance. These differ from partial-coverage or half-shields, which prioritize lighter weight and mobility but offer reduced peripheral protection, typically limited to the eye and upper face area. Attachment systems vary to enhance and compatibility with other PPE; headband-mounted shields use adjustable elastic or straps for secure fit over helmets or alone, while cap-mounted or pivot/flip-up variants allow quick visor elevation for intermittent tasks without full removal. Pivot designs, compliant with OSHA 29 CFR 1910.133 for secondary over primary like , facilitate better airflow and reduce fogging during low-hazard intervals. Feature-based variations include coatings on or PET visors to maintain optical clarity in humid environments, ventilation slots for breathability without compromising seal integrity, and integrated magnification or shaded filters for precision work. Disposable single-use shields, prevalent in medical settings for infection control, contrast with reusable models that withstand disinfection cycles up to 50 times while meeting impact ratings of Z87+ for high-velocity particles. Specialized types, such as those with built-in eyewear frames or extra-wide visors (up to 12 inches), accommodate users needing prescription correction or broader splash deflection, though OSHA mandates they supplement—not replace—primary against fine particulates. In industrial contexts, variations like shaded or high-heat-resistant shields integrate with helmets to filter and radiation per ANSI Z87.1 drop and high-mass tests, enduring temperatures up to 200°C without deformation. Lightweight PET iterations, weighing under 100 grams, prioritize extended wear in dynamic environments, differing from heavier models optimized for durability against 120 ft/s impacts. All certified variants must bear permanent markings indicating compliance, ensuring for hazard-specific selection as outlined in ISEA guidelines.

Historical Development

Early Innovations and Industrial Origins

The earliest known patent for a transparent protective face shield was granted in 1903 to Ellen Dempsey of , for a "sanitary face shield" intended to block disease-producing germs from during medical procedures. This device represented an initial engineering solution for full-face barrier protection, utilizing a transparent —likely glass—to maintain visibility while isolating the wearer from airborne contaminants, addressing causal risks of transmission through direct exposure. Industrial adoption of face shields originated in the early , coinciding with rapid in and the attendant rise in workplace injuries from particulate hazards, such as metal chips from , sparks from grinding, and splashes in chemical handling. These environments demanded protective gear that preserved operational sight without impeding productivity, leading to adaptations of early transparent shields mounted on headbands or visors for use in , , and assembly lines. Pre-plastic versions often relied on or wire-mesh overlays, which provided mechanical resistance but were prone to fogging, shattering, or reduced clarity under sustained use. A pivotal advancement occurred in the 1930s with the commercialization of acrylic plastics, enabling lighter, more resilient shields. Rohm and Haas Company developed Plexiglas—a clear, shatter-resistant —in facilities in Darmstadt, (production began 1934), and Bristol, Pennsylvania (1936), initially for optical and enclosure applications before adapting to safety equipment. This material's superior impact absorption and transparency reduced weight burdens on workers and minimized failure risks compared to , fostering wider integration into industrial protocols and contributing to declining facial injury rates as safety standards evolved.

20th-Century Advancements

In the early , face shields emerged as an extension of protective in industrial settings, providing broader coverage against flying debris, sparks, and chemical splashes in sectors such as , , and . Initially constructed from —a flammable early plastic—these shields offered superior face compared to spectacles alone, though their brittleness limited durability. Mid-century advancements focused on improving ventilation and adjustability to address fogging and user comfort, particularly for welders and machinists. A patent for a vented face shield incorporated louvers to deflect while preventing buildup on the inner surface, enhancing visibility during prolonged use. Similarly, wartime and postwar patents, such as US2328687 granted in 1943, introduced mechanisms for attaching shields to caps with adjustable positioning relative to the wearer's face, facilitating integration with helmets. By the 1960s, face shields saw adoption in for , as evidenced by the Philadelphia Police Department's deployment of polycarbonate models to shield officers from projectiles during street demonstrations. Regulatory standardization accelerated in the latter half of the century; the (ANSI) established eye and face protection criteria in the 1970s, while the (OSHA) mandated their use under 29 CFR 1910.133 for hazards like molten metal and irritants, driving widespread industrial compliance and material shifts toward impact-resistant acetate and early .

COVID-19 Acceleration and Post-Pandemic Innovations

The COVID-19 pandemic triggered a surge in demand for personal protective equipment, prompting accelerated production of face shields through innovative manufacturing techniques. In early 2020, global shortages led manufacturers to pivot rapidly; for instance, JV Manufacturing retooled its operations within 10 days to produce over 13 million face shields by leveraging existing injection molding capabilities. Similarly, MIT initiated mass production of disposable face shields using die-cutting machines, achieving rates of 50,000 units per day within weeks. Institutions like the Wyss Institute at Harvard scaled up to deliver seven million face shields regionally by adapting local supply chains and collaborating with volunteers. Additive manufacturing emerged as a key enabler for decentralized production, with allowing hospitals, universities, and companies to fabricate face shields on-site. shipped initial batches of 3D-printed shields in April 2020, while released open-source designs and guidance to facilitate widespread adoption. Projects such as those at the Skolkovo Institute achieved daily outputs of thousands using light-transparent materials, and Dow introduced a simplified two-piece to boost production efficiency, donating 100,000 units to healthcare providers. These efforts highlighted the role of open-source sharing and in addressing acute PPE needs, though 3D-printed variants often provided physical barriers with limitations in fluid resistance compared to traditional FDA-cleared options. Post-pandemic innovations have focused on enhancing functionality and . Reusable designs, such as those from Fast Radius featuring interchangeable shields cleanable for up to two weeks, emerged to reduce waste and costs. Smart face shields integrating sensors for monitoring physiological parameters like temperature and heart rate have been proposed for ongoing health tracking, including post-recovery from infections. Advances in ergonomic, one-size-fits-all models with improved comfort and assembly without additional components reflect lessons from pandemic-era deployments, prioritizing ease of use in healthcare settings. These developments underscore a shift toward multifunctional PPE resilient to future shortages.

Materials and Manufacturing

Primary Materials Used

Face shields primarily consist of a transparent attached to a frame, with materials selected for optical clarity, durability, and hazard resistance. The , which provides the barrier against impacts, splashes, or aerosols, is most commonly manufactured from , a valued for its high impact strength—up to 250 times that of —and ability to withstand temperatures up to 120°C without deforming. visors typically have a thickness of 1.5 mm for standard models, offering clear vision with minimal distortion while meeting ANSI Z87.1 impact standards. Alternative visor materials include and propionate, which provide superior chemical resistance against solvents and acids compared to , though they exhibit lower impact toughness. , in particular, is favored for applications involving corrosive substances, as it resists degradation from exposure to oils and hydrocarbons, but it is more prone to scratching and fogging without coatings. Polyethylene terephthalate glycol (PETG) or may be used in specialized or 3D-printed visors for flexibility and reduced brittleness, though these are less prevalent in commercial production due to lower optical quality. Frames are generally constructed from lightweight thermoplastics such as or (ABS) to minimize user fatigue, with adjustable designs incorporating plastic hinges or ratcheting mechanisms for fit. In industrial settings, frames may integrate metal brackets—often aluminum or —for attachment to hard hats, enhancing stability under high-heat or conditions. Straps or headbands typically employ elastic polymers like rubber or for secure, sweat-resistant fastening. During the , frames were sometimes produced via additive manufacturing using polylactic acid (PLA), a biodegradable derived from renewable resources, though this material offers inferior long-term durability compared to injection-molded thermoplastics.

Production Methods and Processes

Face shields are primarily manufactured using for the transparent material, followed by cutting and forming techniques, while and headbands are produced via injection molding. or propionate sheets are extruded into flat rolls, providing optical clarity and impact resistance essential for protective barriers. These sheets are then precisely cut to visor dimensions using methods such as , which allows for high precision and minimal waste on thin materials up to 3 mm thick, or die cutting for high-volume runs capable of processing thousands of units from flat stock. Injection molding forms the rigid frame components from thermoplastics like (ABS) or , where molten is injected into molds under pressures of 5,000 to 15,000 psi, enabling complex geometries like adjustable straps and anti-fog retention features; this supports cycle times as low as 20-60 seconds per part in . Thermoforming serves as an alternative for visors requiring curvature to better conform to the face, involving heating extruded sheets to 150-180°C until pliable, then vacuum-forming over aluminum molds to achieve shapes with draw ratios up to 2:1, followed by trimming; this method excels in producing lightweight, disposable shields at rates of hundreds per hour per machine but may introduce optical distortions if cooling is uneven. Assembly integrates the with the frame using mechanical fasteners, , or adhesives like , ensuring a seal against splashes per standards such as ANSI Z87.1, with total production times for assembled units ranging from 40 seconds for flat-packed designs to several minutes for custom fits. includes impact testing at velocities up to 150 ft/s and fog resistance evaluations to verify durability. In response to supply shortages during the COVID-19 pandemic, additive manufacturing via fused deposition modeling (FDM) 3D printing emerged for rapid prototyping and decentralized production of frames, using filaments like polyethylene terephthalate glycol (PETG) at layer heights of 0.2-0.3 mm to yield parts in 1-2 hours per unit; volunteer networks produced over 35,000 shields this way, though scalability was limited compared to injection molding, which output 80,000 units in equivalent efforts due to faster throughput. The U.S. Food and Drug Administration facilitated distribution of more than 500,000 3D-printed face shields by March 2021, prioritizing designs with open-source files for compatibility with consumer printers, but empirical assessments noted higher material costs (up to 5x traditional methods) and variability in fit from printer calibration differences. Post-pandemic, hybrid approaches combining 3D-printed prototypes with injection-molded scaling have informed standardized production, emphasizing biocompatibility and sterilization compatibility under ISO 10993 guidelines.

Primary Applications

Healthcare and Medical Use

Face shields serve as personal protective equipment (PPE) in healthcare settings to protect the eyes, nose, and mouth of medical personnel from splashes, droplets, and sprays of bodily fluids during patient interactions and procedures. They are routinely used in environments involving potential exposure to infectious materials, such as surgical suites, dental clinics, and emergency departments. In dentistry, face shields complement other PPE during aerosol-generating procedures like drilling or scaling, mitigating contamination from splatter that can reach the clinician's face. Studies indicate that face shields reduce surface contamination on the wearer's face by acting as a physical barrier to larger particles, though their efficacy diminishes against finer aerosols without additional respiratory protection. During the , face shields saw widespread adoption in healthcare facilities, often layered over surgical to enhance protection against transmission from respiratory droplets and aerosols. A study demonstrated that face shields reduced immediate viral exposure by approximately 96% for healthcare workers in close proximity (within 18 inches) to a coughing , outperforming in blocking direct forward projection of droplets. In dental settings, combining face shields with significantly lowered the risk of transmission during aerosol-producing treatments, with evidence showing decreased bioaerosol inhalation compared to alone. However, randomized trials found that closed face shields paired with surgical were non-inferior to alone in preventing infections among high-exposure healthcare workers, though adherence and comfort influenced overall utility. Empirical assessments highlight face shields' role in source control, deflecting exhaled droplets from the wearer, which is beneficial in procedural contexts like or where both patient and provider generate bioaerosols. In oral simulations, splatter was notably higher on unprotected areas but reduced on face shields, underscoring their value in containing procedure-generated particles. Guidelines from authorities recommend face shields as adjunctive PPE rather than primary respiratory barriers, emphasizing integration with or respirators for comprehensive against airborne pathogens.

Industrial, Construction, and Welding

In industrial settings, face shields protect workers from hazards including flying particles, molten metal, chemical splashes, and impacts during operations such as machining, grinding, and metalworking. The Occupational Safety and Health Administration (OSHA) requires employers to provide eye and face protection under 29 CFR 1910.133 when employees face such risks, with devices required to meet ANSI/ISEA Z87.1 standards for impact and penetration resistance. These shields typically feature a transparent visor extending from forehead to chin, often paired with underlying safety glasses to address gaps in coverage against lateral threats or fine dust. In environments, face shields safeguard against from activities like chipping, sawing, , and , where large chips, fragments, or tools can strike the face at high velocities. OSHA's standard, 29 CFR 1926.102, mirrors general industry requirements by mandating compliant for exposed workers, emphasizing devices tested for high-velocity impacts under ANSI Z87.1-2020 protocols such as the drop-ball and high-mass tests. Shields rated for splash and impact are preferred for tasks involving wet processes or overhead work, though they must be inspected regularly for scratches or fogging that could impair visibility and efficacy. For and cutting, face shields provide critical defense against and radiation, sparks, and expulsion, preventing flash burns, arc eye, and thermal injuries beyond what filtered helmets alone offer. ANSI Z49.1-2013 specifies that face must incorporate shade levels (e.g., shade 5 for gas ) calibrated to arc intensity, while adhering to Z87.1 for overall durability against molten droplets tested at temperatures up to 1200°F. Hand-held or flip-up shields with auto-darkening lenses enhance in multi-process , reducing while maintaining ; however, full-face coverage is essential during grinding or chipping phases of weld preparation to mitigate secondary hazards like airborne particulates.

Military, Law Enforcement, and Tactical

![US Navy sailor removing face shield from MCU-2-P gas mask][float-right] In military applications, face shields serve as protective visors integrated with ballistic helmets to safeguard against fragmentation, blasts, and blunt force trauma. The Batlskin Visor, developed for advanced combat helmets, features injection-molded with flawless optics, providing NIJ Level IIIA capable of stopping rounds and smaller fragments while maintaining visibility. Similarly, Ops-Core's Multi-Hit Handgun Face Shield attaches to tactical helmets like the FAST series, rated to withstand multiple impacts from 9mm threats, enhancing operator survivability in close-quarters engagements. These systems prioritize modularity, allowing quick deployment or stowage to balance with operational mobility, though full-face ballistic coverage remains limited due to weight constraints exceeding 1-2 kg for visors alone. Law enforcement utilizes face shields primarily in riot control and crowd management, where they form part of standardized protective ensembles to defend against thrown projectiles, liquids, and physical assaults. , often constructed from impact-resistant or acrylic, mount to helmets such as the ACH or PASGT variants and comply with NIJ Standard 0104.02, which mandates resistance to impacts from objects like 38-caliber lead slugs at specified velocities. Models like the Paulson DK5 series incorporate and anti-abrasion coatings, with V-50 fragmentation ratings ensuring durability in prolonged disturbances; for instance, the DK5-X.250AFS weighs 553 grams and provides a 15.2 cm by 0.64 cm viewing window optimized for peripheral awareness. These shields enable officers to maintain visual contact while mitigating risks from debris or bodily fluids, as evidenced in deployments during civil unrest events. Tactical operations in both military and teams extend face shield use to high-threat scenarios such as hostage rescues, responses, and forced entries, where ballistic variants offer supplementary defense beyond standard eyewear. In applications, shields rated for NIJ IIIA protection integrate with plate carriers and helmets to counter fire and shrapnel, with real-world deployments noted in raid operations as of 2025. materials dominate due to their high impact resistance—up to 250 times that of glass—and transparency, though limitations include reduced compared to unprotected vision and vulnerability to rifle-caliber threats. Overall, these applications emphasize layered protection, with face shields complementing rather than replacing primary body armor.

Effectiveness Assessment

Protection Against Physical and Chemical Hazards

Face shields provide secondary protection against physical hazards such as flying fragments, large chips, objects, and particles by forming a barrier that absorbs or deflects moderate impacts. Under ANSI/ISEA Z87.1-2020, compliant face shields must withstand high-velocity impact tests, including a 1/4-inch ball propelled at 150 feet per second (46 meters per second), demonstrating resistance to typical industrial projectiles without shattering or penetrating the . Laboratory evaluations of face shields have shown they maintain structural integrity against repeated low-to-moderate energy impacts, though performance degrades with material fatigue or improper fit. However, face shields alone do not suffice for primary against impacts, as they permit peripheral exposure and lack the contoured seal of ; regulatory guidance mandates pairing them with ANSI Z87.1-certified spectacles or to mitigate penetration risks from high-speed debris. In empirical impact testing, multi-layered protection combining face shields with underlying has proven superior, reducing facial injury risk by distributing force and preventing visor deflection onto the eyes, whereas standalone shields may fail against projectiles exceeding standard test energies, such as those above 50 joules. Limitations include vulnerability to sharp or angular fragments that could chip the and inadequate shielding against ballistic threats or extreme velocities encountered in specialized environments like or . For , face shields act as a physical barrier against splashes, sprays, and larger droplets of hazardous liquids, safeguarding the face, eyes, and mucous membranes from corrosive or irritant substances. Propionate visors, valued for their chemical resistance, prevent penetration from acids, bases, and solvents during incidental spills, as verified through splash resistance protocols in standards like ANSI Z87.1, which require no liquid passage after exposure to simulated chemical jets. They are particularly effective in and industrial settings for gross exposures, where they reduce facial contamination by intercepting droplets greater than 100 micrometers, though efficacy diminishes with visor fogging or gaps at the edges. Unlike sealed , face shields offer no defense against chemical vapors, mists, or gases, which can bypass the open design; thus, they complement but do not replace respiratory apparatus or vapor-tight for airborne hazards. Real-world assessments underscore their utility in preventing direct splash injuries but emphasize the need for immediate protocols, as residual liquids on the exterior pose secondary risks.

Empirical Evidence on Respiratory and Aerosol Filtration

Empirical studies demonstrate that face shields primarily block large respiratory droplets (>100 μm) expelled during coughing or sneezing, reducing short-term exposure for the wearer by deflecting particles away from the face. In a 2016 manikin-based experiment simulating cough aerosols, face shields decreased inhaled particle counts by up to 96% for large droplets when positioned 30 cm from the source, with efficacy dropping at greater distances due to dispersion. However, protection diminishes rapidly beyond 45 cm, as smaller particles disperse laterally. For smaller aerosols (1-5 μm, relevant to SARS-CoV-2 transmission), face shields exhibit substantial leakage due to their open perimeter, allowing airflow around the sides, bottom, and top. High-speed and laser-based visualizations from 2020 revealed that aerosols from or speech curve around the shield's edges, bypassing entirely and potentially contaminating nearby individuals. A 2021 study using particle counters found face shields reduced inward penetration by only 23-52% for submicron particles, inferior to surgical (68-89%) owing to poor seal integrity. As source control devices, face shields limit forward projection of cough-generated aerosols but fail to contain lateral or upward leakage effectively. experiments indicated shields trap <20% of expelled aerosols compared to masks, with particles escaping via gaps and traveling up to 1 meter sideways. Combined with masks, shields add marginal aerosol filtration benefits, but standalone use yields total outward leakage efficiencies below 50% for viral-sized particles. One countervailing study reported shields outperforming masks in blocking inhaled submicron particles (<1 μm) by 10-30% in static airflows, attributed to deflection rather than true filtration, though real-world movement exacerbates leaks.
Particle Size RangeFace Shield Efficacy (Inward Protection)Comparison to Surgical MaskKey Limitation
>100 μm (large droplets)80-96% reduction in exposureComparable or slightly better for deflectionDistance-dependent; ineffective >45 cm
1-5 μm (aerosols)23-52% reductionInferior (masks: 68-89%)Side/bottom leakage from poor fit
<1 μm (submicron)Variable; up to 30% better deflection in controlled testsMixed; masks superior in dynamic scenariosAirflow bypass, not filtration
These findings underscore that while face shields mitigate splash risks, their aerosol filtration is compromised by design-induced leaks, rendering them suboptimal for respiratory pathogen control without supplementary measures.

Limitations and Empirical Critiques

Scenarios of Inadequate Protection

Face shields fail to provide adequate protection in scenarios involving small aerosolized particles, such as those generated by respiratory pathogens, due to unsealed gaps at the sides, bottom, and top that permit airflow leakage and particle ingress. In laboratory simulations of cough aerosols, face shields blocked only 2% of particles on average, allowing the majority to circumvent the barrier via peripheral leakage. This inadequacy is exacerbated in close-proximity interactions, where exhaled aerosols from an infected individual can enter the wearer's breathing zone by flowing around the shield's edges. During prolonged exposure exceeding short durations (e.g., beyond 10-30 minutes), face shields permit particle accumulation within the enclosed space, reducing initial protective efficacy as contaminated air recirculates near the face. Empirical tests using mannequins demonstrated that while shields deflect larger droplets (>5 μm), submicron aerosols (<1 μm) evade capture by following air currents through gaps, particularly under dynamic conditions like head movement or ventilation airflow. In aerosol-generating medical procedures, such as intubation, standard face shields offered insufficient containment of virus-laden particles compared to sealed alternatives, with leakage rates allowing detectable inward exposure. High-velocity exhalations or environmental air disturbances, including those from talking or coughing at distances under 1 meter, create turbulent flows that direct aerosols past the shield's visor, rendering it ineffective for wearer protection against pathogens like SARS-CoV-2. No tested face shield design achieved complete droplet blockade in controlled evaluations, with side and bottom gaps consistently permitting partial exposure even against moderate splatter. These failures highlight face shields' unsuitability as standalone respiratory barriers in unventilated or crowded settings, where reliance on them alone correlates with elevated inhalation risks.

Practical Drawbacks and User Compliance Issues

Face shields often cause fogging due to exhaled breath condensing on the visor, impairing visibility for 50.0% to 73.9% of healthcare workers across tested designs. This issue exacerbates vision-related problems, including glare, which contribute to reduced surgical efficiency reported by 74.1% of oral health professionals during the . Heat buildup and humidity inside the shield lead to discomfort for 41.9% to 69.3% of users, while pressure on the temples or face induces headaches, dizziness, and skin irritation. Ergonomic limitations, such as inadequate adjustability and weight distribution, further diminish work efficiency and user comfort during prolonged wear. Disinfection challenges, including time-consuming cleaning and material degradation, add to operational burdens in clinical settings. User compliance with face shields is notably lower than with masks, with only 27.4% of participants in a randomized trial reporting high adherence when using shields over masks, compared to 88.6% for masks alone. Over 50% of healthcare personnel cite discomfort as a primary reason for noncompliance, directly tied to fogging, heat, poor visibility, and pressure-related symptoms. In procedural environments, workers frequently remove shields for eating, drinking, or brief rests, with discomfort cited in 37.1% of removal instances during weekdays. Low confidence in the shield's seal and persistent ergonomic issues, such as inadequate ventilation and fit, undermine sustained use, particularly in high-demand scenarios like surgery or patient care. These factors collectively result in intermittent protection, as evidenced by decreased adherence during extended shifts or in warmer environments.

Standards and Regulatory Framework

International and National Standards

Internationally, the International Organization for Standardization (ISO) provides frameworks for eye and face protection under series such as ISO 16321-1:2021, which establishes safety and performance requirements for occupational eye and face protectors, including face shields as secondary devices offering broader facial coverage against splashes and low-energy impacts. ISO 19734:2021 offers guidance on selecting, using, and maintaining these protectors to ensure compatibility with primary eyewear and adequate field of vision. ISO 4007:2018 defines terminology for personal eye and face protection, facilitating consistent application across global contexts. These standards emphasize mechanical integrity, optical clarity, and resistance to environmental factors but do not specify protections against biological aerosols, highlighting a gap in harmonized requirements for infectious disease scenarios. In the European Union, EN 166:2001 sets minimum functional specifications for personal eye protection, extending to face shields through requirements for mechanical strength, resistance to surface damage, fogging, and liquid splashes, with mandatory markings like "1" for low-energy impact or "B" for medium-energy impact resistance. This standard integrates with EN 167 for optical testing and EN 168 for non-optical tests, ensuring shields maintain visibility and durability during use. EN 166 is undergoing transition to EN ISO 16321:2022, which imposes stricter testing for occupational eyewear and face protectors, including enhanced assessments for welding-related hazards and broader applicability to integrated systems. Nationally, in the United States, ANSI/ISEA Z87.1-2020 governs occupational and educational eye and face protection, classifying face shields under secondary protectors that must pass drop tests for durability, high-velocity impact resistance (e.g., via 1/4-inch steel ball at specified speeds), and splash protection via fluid exposure simulations. Devices compliant with this standard bear the Z87.1 mark, indicating general requirements for coverage extending to the forehead, temples, and chin, with options for high-impact (Z87.1+) designation after rigorous ballistic testing. The Occupational Safety and Health Administration (OSHA) enforces these via 29 CFR 1910.133 for general industry and 1926.102 for construction, mandating employer-provided protection meeting ANSI Z87.1 or equivalent consensus standards to mitigate hazards like flying particles and chemical splashes. For medical applications, the Food and Drug Administration (FDA) classifies face shields as Class I exempt devices under 21 CFR 878.4370, requiring general controls but deferring to ANSI for performance without dedicated biohazard filtration criteria. Other national variations exist; for instance, in Canada, the Canadian Standards Association (CSA) Z94.3 aligns closely with ANSI Z87.1 for industrial face protection, while Australia's AS/NZS 1337 series mirrors EN 166 in specifying impact and splash ratings. Compliance across jurisdictions often hinges on third-party certification, with standards prioritizing empirical testing over theoretical models to verify real-world hazard mitigation.

Testing Protocols and Certification

Testing protocols for face shields emphasize impact resistance, penetration resistance, optical quality, and fluid splash protection to ensure reliability against occupational hazards. In the United States, the primary standard is ANSI/ISEA Z87.1-2020, which requires face shields to undergo drop-ball impact testing where a 1-inch diameter steel ball is dropped from 50 inches (127 cm) onto the visor to verify basic protection integrity. For enhanced designation (Z87+ marking), high-velocity impact testing involves propelling a 1/4-inch steel ball at 150 feet per second (46 m/s), simulating flying debris. Penetration resistance is assessed by dropping a weighted needle from 50 inches to confirm the visor material prevents puncture. Flammability tests expose the visor to a butane flame for 5 seconds, requiring no ignition or sustained burning. Splash protection under ANSI Z87.1, denoted by D3 marking, evaluates resistance to liquid droplets using a simulated blood mixture (glycerin and water) sprayed at 8 feet per second from 10 inches, ensuring no penetration through the visor. Optical tests measure refractive power, astigmatism, and visual acuity to limit distortion, with additional assessments for haze and luminous transmittance. The U.S. Occupational Safety and Health Administration (OSHA) enforces compliance via 29 CFR 1910.133, mandating eye and face protection meet ANSI Z87.1 criteria in hazardous environments, though certification remains voluntary and manufacturer-declared following third-party lab verification. In Europe, EN 166:2001 governs personal eye protection, including face shields, with mechanical strength tests categorized by energy levels: low (F, 6 mm steel ball at 40 m/s), medium (B, 6 mm at 12 m/s drop equivalent), and high (A, applicable to face shields via larger impacts like 22 mm ball drops). Droplet resistance for field 3 use requires no visor deformation or penetration from liquid sprays, tested under EN 167 optical protocols. This standard transitions to EN ISO 16321-1:2022 (effective November 2024), incorporating updated impact and optical tests for broader PPE conformity under EU PPE Regulation (EU) 2016/425, requiring CE marking via notified body assessment for Category II/III risks. International ISO efforts, via TC 94/SC 6, harmonize these through ISO 16321 series for general requirements and test methods, emphasizing empirical validation of coverage and durability. Certification involves accredited labs issuing reports, with manufacturers affixing permanent markings (e.g., Z87.1, EN 166 B/A) to indicate passed tests.

Controversies and Policy Debates

Overreliance in COVID-19 Public Health Guidance

Early in the , face shields were promoted in certain public health contexts as viable alternatives or supplements to masks, driven by global shortages of N95 respirators and surgical masks, with advocates suggesting they could provide broad protection against respiratory droplets when universally adopted. This enthusiasm led to widespread grassroots efforts, including 3D printing initiatives that produced millions of shields for distribution to healthcare workers and the public by mid-2020. However, empirical evidence soon revealed significant limitations, as transmission occurs predominantly via aerosols—fine particles under 5 μm that readily leak around the open sides, top, and bottom of face shields, bypassing filtration. Computational fluid dynamics simulations conducted by researchers at Japan's Kyoto University in September 2020, utilizing supercomputer modeling of airflow and particle dispersion, demonstrated that face shields offered virtually no containment of exhaled aerosols, with over 90% of particles escaping laterally and dispersing up to 2 meters away, rendering them ineffective for source control. Laboratory experiments corroborated this, showing face shields reduced wearer exposure to incoming aerosols by only 23% in close proximity, far inferior to cloth masks which achieved up to 70% reduction, and providing no significant improvement over no barrier for small particle inhalation due to inward leakage currents. Despite accumulating data on aerosol dynamics, some policies in schools and workplaces allowed face shields as mask substitutes, particularly for children, educators, or individuals with sensory sensitivities, potentially contributing to higher transmission risks by promoting incomplete protection. The U.S. Centers for Disease Control and Prevention (CDC) explicitly advised against relying on face shields alone, classifying them as supplemental for eye protection rather than respiratory barriers, a stance echoed by state health departments warning of their inadequacy as standalone measures. This pattern of initial overreliance underscored a disconnect between precautionary guidance amid uncertainty and the physics of aerosol propagation, where shields' design—optimized for splash hazards—failed to address viral causality effectively.

Comparative Efficacy Versus Masks and Alternatives

Face shields exhibit substantially lower efficacy than masks in preventing the transmission of respiratory aerosols and droplets, primarily due to unsealed edges that permit leakage during both exhalation and inhalation. Laboratory experiments simulating cough-generated aerosols demonstrate that face shields reduce outward emission by only about 23% at 0.5 meters, compared to surgical masks achieving 70-90% reductions and N95 respirators exceeding 95%. This leakage arises from air currents bypassing the shield's perimeter, allowing fine particles (1-5 μm, relevant to ) to escape or enter unimpeded, unlike the filtration mechanism of masks. For wearer protection against incoming aerosols, face shields provide modest deflection of large droplets (>10 μm) but inferior containment of smaller respirable particles compared to surgical , which filter 50-75% of such s depending on fit. N95 respirators outperform both, with filtration efficiencies near 98% for particles as small as 0.3 μm, as confirmed in multiple randomized trials during outbreaks showing reduced infection odds (OR 0.30) with respirators versus surgical (OR 0.58). One mannequin-based study suggested shields might outperform loose-fitting for ultra-fine particles (<1 μm) in controlled airflow, but this finding contrasts with real-world dynamics where convective flows enhance shield leakage, rendering consistently superior for barrier effects. Versus alternatives like or visors without respiratory coverage, face shields offer broader deflection but no inherent filtration advantage, with combined use (shield plus ) yielding additive protection—up to 97% reduction—superior to either alone. However, standalone shields fail as substitutes in high- scenarios, as evidenced by higher surface and particle penetration in procedural simulations compared to masked controls. Empirical data from healthcare settings during indicate that mandates reduced transmission more effectively than shield-only policies, underscoring shields' role as supplementary rather than primary respiratory defenses.

References

  1. https://www.safeopedia.com/definition/9058/face-shield
  2. https://pmc.ncbi.nlm.nih.gov/articles/PMC5015006/
  3. https://www.osha.gov/eye-face-protection
  4. https://wesco.com/us/en/knowledge-hub/articles/should-safety-glasses-be-worn-under-faceshields.html
  5. https://www.osha.gov/laws-regs/regulations/standardnumber/1910/1910.133
  6. https://safetyculture.com/topics/ppe-safety/face-protection
  7. https://pmc.ncbi.nlm.nih.gov/articles/PMC4734356/
  8. https://pubmed.ncbi.nlm.nih.gov/24467190/
  9. https://pmc.ncbi.nlm.nih.gov/articles/PMC9345365/
  10. https://pmc.ncbi.nlm.nih.gov/articles/PMC7922468/
  11. https://dimensionsofdentalhygiene.com/article/abcs-face-shields/
  12. https://www.seton.com/resource-center/a-beginners-guide-to-faceshields-materials-standards-and-more/
  13. http://www.osha.gov/laws-regs/regulations/standardnumber/1910/1910.133
  14. https://shannonoptical.com/wp-content/uploads/2023/07/ANSI-ISEA-Z87-1-2020.pdf
  15. https://wwwn.cdc.gov/PPEInfo/Standards/Info/ANSI/ISEAZ8712020
  16. https://nocry.com/blogs/news/your-guide-to-the-different-types-of-face-shields
  17. https://www.leelinework.com/types-of-medical-face-shields/
  18. https://www.medtecs.com/face-shields-standard-materials-and-structures/
  19. https://www.osha.gov/etools/shipyard/general-requirements/ppe/ppe-selection/eye-face-protection
  20. https://alliedusa.net/7-types-of-face-shields-to-be-used-for-covid-19/
  21. https://bisonlifeusa.com/blogs/news/how-to-choose-the-right-face-shield-for-your-needs
  22. https://www.hmpgloballearningnetwork.com/site/emsworld/article/1222567/eye-protection-forgotten-ppe
  23. https://safecosafety.co.za/the-evolution-of-ppe/
  24. https://trustyppe.com/10-facts-about-face-shields/
  25. https://philadelphiaencyclopedia.org/artifacts/artifact-face-shield/
  26. https://rpcomtrade.com/workplace-safety-gear/
  27. https://patents.google.com/patent/US2655656A/en
  28. https://patents.google.com/patent/US2328687
  29. https://blog.jvmfgco.com/case-studies/pandemic-face-shield-production
  30. https://news.mit.edu/2020/face-shield-ppe-manufacture-covid-19-0331
  31. https://wyss.harvard.edu/news/seven-million-face-shields-and-counting/
  32. https://www.boeing.com/features/2020/04/first-batch-of-3d-printed-face-shields-shipped-out
  33. https://www.stratasys.com/en/covid-19/
  34. https://pmc.ncbi.nlm.nih.gov/articles/PMC7277794/
  35. https://investors.dow.com/en/news/news-details/2020/Dow-develops-simplified-lightweight-design-for-face-shields-to-help-protect-healthcare-professionals-shares-open-source-design-to-encourage-additional-production/default.aspx
  36. https://scmr.org/news/3d-printing-in-healthcare-in-response-to-the-covid-19-crisis/
  37. https://fastradius.com/covid-19/face-shields/
  38. https://pmc.ncbi.nlm.nih.gov/articles/PMC9527148/
  39. https://www.sciencedirect.com/science/article/pii/S2405844023065763
  40. https://www.paulsonmfg.com/blog/understanding-the-different-types-of-plastics-used-for-face-shields-goggles/
  41. https://www.leelinework.com/face-shield-material/
  42. https://droppe.com/blog/article/guide-to-choosing-a-chemical-protection-face-shield/
  43. https://www.fastenal.com/product/details/1002043
  44. https://www.kleintools.com/catalog/face-shields/replacement-face-shield-frame
  45. https://www.sciencedirect.com/science/article/pii/S2666790823000204
  46. https://www.weetect.com/products/face-shield/
  47. https://www.weprofab.com/thermoforming-face-shield/
  48. https://go.usa.gov/xv8mu
  49. https://www.fda.gov/media/136842/download
  50. https://www.researchgate.net/publication/347290996_Additive_manufacturing_and_injection_molding_process_for_mass-production_of_face_shields_during_COVID-19_pandemic_A_comparative_study
  51. https://www.fda.gov/emergency-preparedness-and-response/coronavirus-disease-2019-covid-19/3d-printing-fdas-rapid-response-covid-19
  52. https://pmc.ncbi.nlm.nih.gov/articles/PMC7557567/
  53. https://stacks.cdc.gov/view/cdc/41208
  54. https://decisionsindentistry.com/article/face-shield-use-during-covid-19-pandemic/
  55. https://pmc.ncbi.nlm.nih.gov/articles/PMC9329084/
  56. https://jamanetwork.com/journals/jama/fullarticle/2765525
  57. https://pmc.ncbi.nlm.nih.gov/articles/PMC7997726/
  58. https://trialsjournal.biomedcentral.com/articles/10.1186/s13063-022-06606-0
  59. https://www.tandfonline.com/doi/full/10.1080/02786826.2020.1862409
  60. https://twin-cities.umn.edu/news-events/first-its-kind-splatter-study-examines-infection-control-during-oral-surgery
  61. https://blog.ansi.org/ansi/ansi-isea-z87-1-2020-safety-glasses-eye-protection/
  62. https://marketplace.safetyculture.com/us/blog/are-safety-glasses-required-under-a-face-shield
  63. http://www.osha.gov/laws-regs/regulations/standardnumber/1926/1926.102
  64. https://apps.ocfl.net/dept/county_admin/public_safety/risk/Eye_Face_Protection.pdf
  65. https://www.osha.gov/sites/default/files/publications/OSHAfactsheet-eyeprotection-during-welding.pdf
  66. https://www.ccohs.ca/oshanswers/safety_haz/welding/ppe.html
  67. https://safetyware.com/protecting-your-vision-the-importance-of-welding-face-shields/
  68. https://www.galvion.com/case-study/advancing-head-and-face-protection
  69. https://www.atomicdefense.com/products/ops-core-ballistic-face-shield
  70. https://www.hardheadveterans.com/products/ballistic-face-shield-nij-iiia
  71. https://nij.ojp.gov/library/publications/riot-helmets-and-face-shields-nij-standard-010402
  72. https://www.paulson-international.com/products/tactical-ppe/face-shields/dk5-x-250af-2/
  73. https://www.paulsonmfg.com/blog/the-paulson-rundown-tactical-face-shields-101/
  74. https://www.linkedin.com/pulse/ballistic-face-shield-real-world-5-uses-youll-actually-jvoxc/
  75. https://www.thomasnet.com/insights/polycarbonate-protective-gear-for-tactical-applications/
  76. https://www.acplasticsinc.com/informationcenter/r/ballistic-material-for-riot-gear-and-face-shields
  77. https://www.paulsonmfg.com/blog/an-intro-to-the-ansi-z87-1-safety-standard-for-face-eye-protection/
  78. https://stacks.cdc.gov/view/cdc/209226/cdc_209226_DS1.pdf
  79. https://www.osha.gov/sites/default/files/publications/osha3151.pdf
  80. https://www.mdpi.com/2813-8856/2/3/16
  81. https://us.msasafety.com/Face-Protection/V-Gard%25C2%25AE-Visors/V-Gard%25C2%25AE-Propionate-Visors-for-Chemical-and-Splash/p/000060007000001220?locale=en
  82. https://ehs.princeton.edu/workplace-construction/workplace-safety/physical-safety/personal-protective-equipment-ppe/eye-and-face-protection
  83. https://www.ehs.wvu.edu/hsc/laboratory-safety-hsc/personal-protective-equipment-ppe/eye-face-protection
  84. https://pubs.aip.org/aip/pof/article/32/9/091701/1058951/Visualizing-droplet-dispersal-for-face-shields-and
  85. https://www.tandfonline.com/doi/full/10.1080/02786826.2021.1890687
  86. https://www.sciencedirect.com/science/article/abs/pii/S0196655321000213
  87. https://bigthink.com/health/face-shield-covid/
  88. https://www.medrxiv.org/content/10.1101/2020.07.06.20147090.full
  89. https://www.nature.com/articles/s41598-023-42403-8
  90. https://www.businessinsider.com/coronavirus-face-shields-valved-masks-fail-to-stop-small-droplets-2020-9
  91. https://www.ajicjournal.org/article/S0196-6553%2822%2900050-5/fulltext
  92. https://pmc.ncbi.nlm.nih.gov/articles/PMC8861890/
  93. https://pmc.ncbi.nlm.nih.gov/articles/PMC10169170/
  94. https://journals.sagepub.com/doi/10.1177/1071181322661513
  95. https://www.iso.org/standard/62527.html
  96. https://www.wiseworksafe.com/blog/view/understanding-en-166-personal-eye-protection-standard
  97. https://www.uvex-safety.com/en/knowledge/safety-standards/safety-glasses/
  98. https://www.uvex-safety.com/blog/new-protective-eyewear-standards-en-iso-163212022/
  99. https://www.fda.gov/medical-devices/personal-protective-equipment-infection-control/n95-respirators-surgical-masks-face-masks-and-barrier-face-coverings
  100. https://safetyequipment.org/wp-content/uploads/2022/10/ISEA-EF-2016-Selection-and-Use-1-1.pdf
  101. https://www.testresources.net/applications/standards/ansi/ansi-z87-1-testing-standard-for-safety-eyewear
  102. https://skanwear.com/blogs/ppe-standards/en-166
  103. https://www.szutest.com/information-certification-process-safety-goggles-face-shields/
  104. https://www.iso.org/committee/50612.html
  105. https://www.forbes.com/sites/jvchamary/2020/10/23/covid19-coronavirus-aerosols/
  106. https://www.theguardian.com/world/2020/sep/22/face-shields-ineffective-trapping-aerosols-japanese-supercomputer-coronavirus
  107. https://www.scmp.com/news/china/science/article/3100051/covid-19-research-shows-downsides-face-shields-and-valve-masks
  108. https://www.edweek.org/leadership/do-face-shields-protect-against-covid-19-a-mask-and-shield-explainer/2020/11
  109. https://www.acialliance.org/page/consideration-of-face-shields-as-return-to-school-option
  110. https://odh.ohio.gov/media-center/odh-news-releases/face-shields-not-appropriate-substitute-for-masks
  111. https://abcnews.go.com/Health/face-shields-replace-masks-experts-hope-work-resort/story?id=72092931
  112. https://www.nature.com/articles/s41598-020-72798-7
  113. https://www.ajicjournal.org/article/S0196-6553(21)00021-3/fulltext
  114. https://pmc.ncbi.nlm.nih.gov/articles/PMC10186565/
  115. https://pmc.ncbi.nlm.nih.gov/articles/PMC9111143/
  116. https://ncceh.ca/resources/evidence-briefs/face-shields-public-better-nothing-not-good-enough
  117. https://www.cdc.gov/mmwr/volumes/71/wr/mm7106e1.htm
  118. https://www.phc.ox.ac.uk/news/comprehensive-review-confirms-masks-reduce-covid-19-transmission
Add your contribution
Related Hubs
User Avatar
No comments yet.