Hubbry Logo
DIACDIACMain
Open search
DIAC
Community hub
DIAC
logo
8 pages, 0 posts
0 subscribers
Be the first to start a discussion here.
Be the first to start a discussion here.
Contribute something
DIAC
DIAC
DIAC
View on Wikipedia
from Wikipedia
DIAC
Component typePassive
Pin namesanode 1, anode 2
Electronic symbol
Three-layer DIAC

The DIAC (diode for alternating current) is a diode that conducts electrical current only after its breakover voltage, VBO, has been reached momentarily. Three, four, and five layer structures may be used.[1] Behavior is similar to the voltage breakdown of a TRIAC without a gate terminal.

When breakdown occurs, internal positive feedback (impact ionization or two transistor feedback) ensures that the diode enters a region of negative dynamic resistance, leading to a sharp increase in current through the diode and a decrease in the voltage drop across it (typically full switch-on takes a few hundred nanoseconds to microseconds). The diode remains in conduction until the current through it drops below a value characteristic for the device, called the holding current, IH. Below this threshold, the diode switches back to its high-resistance, non-conducting state. This behavior is bi-directional, meaning typically the same for both directions of current.

Most DIACs have a three-layer structure with breakover voltage of approximately 30 V and an on voltage of less than 3 V. Their behavior is analogous to the striking and extinction voltages of a neon lamp, but it can be more repeatable and takes place at lower voltages.

DIACs have no gate or trigger electrode, unlike some other thyristors that they are commonly used to trigger, such as TRIACs. Some TRIACs, like Quadrac, contain a built-in DIAC in series with the TRIAC's gate terminal for this purpose.

DIACs are also called "symmetrical trigger diodes" due to the symmetry of their characteristic curve. Because DIACs are bidirectional devices, their terminals are not labeled as anode and cathode but as A1 and A2 or main terminal MT1 and MT2.

Typical DIAC voltage and current relationships. VBO is the breakover voltage.

SIDAC

[edit]
SIDAC
Idealized breakover diode voltage and current relationships. Once the voltage exceeds the turn-on threshold, the device turns on and the voltage rapidly falls while the current increases.

A silicon diode for alternating current (SIDAC) is a less commonly used device, electrically similar to the DIAC, but having, in general, a higher breakover voltage and greater current handling capacity.[citation needed]

The SIDAC is another member of the thyristor family. Also referred to as a SYDAC (silicon thyristor for alternating current), bi-directional thyristor breakover diode, or more simply a bi-directional thyristor diode, it is technically specified as a bilateral voltage triggered switch. Its operation is similar to that of the DIAC, but a SIDAC is always a five-layer device with low-voltage drop in latched conducting state, more like a voltage triggered TRIAC without a gate. In general, SIDACs have higher breakover voltages and current handling capacities than DIACs, so they can be directly used for switching and not just for triggering of another switching device.

The operation of the SIDAC is functionally similar to that of a spark gap, but is unable to reach its higher temperature ratings. The SIDAC remains nonconducting until the applied voltage meets or exceeds its rated breakover voltage. Once entering this conductive state going through the negative dynamic resistance region, the SIDAC continues to conduct, regardless of voltage, until the applied current falls below its rated holding current. At this point, the SIDAC returns to its initial nonconductive state to begin the cycle once again.

Somewhat uncommon in most electronics, the SIDAC is relegated to the status of a special purpose device. However, where part-counts are to be kept low, simple relaxation oscillators are needed, and when the voltages are too low for practical operation of a spark gap, the SIDAC is an indispensable component.

Similar devices, though usually not functionally interchangeable with SIDACs, are the thyristor surge protection device (TSPD) sold under trademarks like Trisil by STMicroelectronics and SIDACtor and its predecessor Surgector by Littelfuse. These are designed to tolerate large surge currents for the suppression of overvoltage transients. In many applications this function is now served by metal oxide varistors (MOVs), particularly for trapping voltage transients on the power mains.

Applications

[edit]

DIACs and SIDACs are often used to deliver a pulse once a capacitor has charged to the breakdown voltage, giving both controlled delay set by the charging resistor and a fixed pulse energy set by the capacitor and breakdown voltage. This is common in simple phase angle controls for AC lamp dimmers and motor speed controls. They may also be used to sense over-voltage fault conditions to provide a 'crowbar' function to operate a fuse or a latching alarm that can only be reset by removing the supply.

See also

[edit]

References

[edit]
[edit]
Revisions and contributorsEdit on WikipediaRead on Wikipedia

DIAC

View on Grokipedia
from Grokipedia
A DIAC, or Diode for Alternating Current, is a two-terminal bidirectional switch that conducts electrical current in both forward and reverse directions only after its breakover voltage (V_BO) is momentarily exceeded, typically ranging from 20 to 40 volts depending on the device. This device functions as a trigger mechanism in AC circuits, remaining non-conductive below the breakover threshold and latching into conduction until the current drops below a holding level, making it ideal for symmetric switching in applications. Structurally, a DIAC is often constructed as a three-layer p-n-p-n device, equivalent to two Shockley diodes connected in inverse parallel, which enables its bidirectional operation without a preferred direction. Its symbol resembles a but with symmetric terminals, and it lacks a terminal, relying solely on voltage across its and for triggering. In operation, when connected to an AC source like a , the DIAC blocks current until the voltage peaks surpass V_BO, at which point it fires, providing a sharp pulse to initiate conduction in associated devices. DIACs are prominently used in conjunction with TRIACs for phase control in circuits, such as light dimmers, universal motor speed controllers, and heat regulators, where precise triggering ensures efficient and symmetric power delivery. They are valued for their simplicity, low cost, and reliability. Despite advancements in solid-state switching, DIACs remain a fundamental component in legacy and cost-sensitive AC control systems.

History and Development

Invention and Early Concepts

The DIAC emerged in the late as a key advancement within General Electric's (GE) family, building directly on the 1957 invention and commercialization of the (SCR) by GE engineers. This development occurred amid broader efforts to create solid-state alternatives to vacuum tubes for power control, enabling more reliable and compact AC switching devices. The initial concepts for the DIAC centered on bidirectional , designed to provide symmetric triggering for circuits without requiring external control signals. Inspired by the limitations of tubes in industrial and consumer applications like motor controls and , GE researchers aimed to harness silicon's properties for two-way conduction that activated only above a specific voltage threshold. Prototypes were first realized in 1958 by Jr. and R. W. Aldrich at GE, targeting symmetric operation in early AC dimmer circuits and similar setups. These efforts marked the DIAC as a foundational, gate-less member of the thyristor lineage. A primary early challenge was engineering consistent symmetric breakdown voltages across both polarities without a dedicated gate terminal, which demanded precise doping and junction design to ensure reliable bidirectional performance.

Commercialization and Evolution

The first commercial release of the DIAC occurred in the early , with playing a key role in its development during the 1957–1963 period as part of broader advancements in technology. By 1964, DIACs were integrated into consumer products, notably lamp dimmers, where they served as bidirectional triggers for controlling , enabling the first widespread consumer applications in household lighting control. This marked a significant step in making accessible for everyday use, transitioning from industrial prototypes to affordable discrete components. In the , DIAC evolution shifted toward integration with , exemplified by the development of the Quadrac—a single-package device combining a DIAC trigger with a TRIAC for simplified and improved efficiency in AC switching. This period also saw key milestones, including adoption in controls for appliances like fans and power tools, where DIACs provided symmetrical triggering to enable variable speed operation without complex gating circuits. By the 1980s, refinements focused on enhancing voltage symmetry and reliability, such as through lateral structures that reduced asymmetry in breakover voltages and improved characteristics for more stable performance in demanding environments. Compliance with RoHS directives has been standard since 2006, driving the use of lead-free materials to meet environmental regulations while maintaining performance. efforts have facilitated integration into modern devices, such as smart home dimmers and motor controllers.

Structure and Construction

Internal Layer Configuration

The DIAC, or for , features a structure designed for bidirectional operation, typically configured as either a three-layer p-n-p or a five-layer p-n-p-n-p arrangement to ensure symmetrical conduction in both voltage polarities. The three-layer variant is the most common. In the three-layer variant, the device resembles an open-base bipolar with a central n-type region of high resistivity flanked by two p-type outer layers, enabling across the reverse-biased junction when the applied voltage exceeds the breakover threshold. This setup forms the equivalent of two back-to-back Shockley diodes, providing the bidirectional symmetry essential for AC triggering applications. The junction arrangement in both configurations emphasizes a central high-resistivity region—often the middle n-layer in the three-layer p-n-p or the central p-n pair in the five-layer p-n-p-n-p—that facilitates uniform for reliable triggering. Outer layers are heavily doped to minimize on-state resistance once conduction begins, allowing low-voltage drop during the conducting phase and supporting efficient current flow in either direction. The five-layer structure, with alternating p and n regions (e.g., p-n-p-n-p), enhances this symmetry by integrating two interconnected four-layer sections, akin to inverse-parallel Shockley diodes without control, which collectively mimic two four-layer thyristors operating bidirectionally. From an perspective, the DIAC can be modeled as two four-layer thyristors connected in inverse parallel, lacking gate terminals and relying solely on voltage-induced breakdown for , which underscores its role as a simple, uncontrolled bidirectional switch. Variations include four-layer p-n-p-n configurations, which offer higher in precision applications by reducing in breakover voltages between positive and negative cycles. This layer topology directly contributes to the DIAC's ability to trigger conduction symmetrically, linking to its operating principles in AC circuits.

Materials and Fabrication Techniques

DIACs are primarily fabricated using high-purity silicon wafers as the base material, which can start as either n-type or p-type substrates depending on the desired layer configuration. To form the necessary p-n junctions in devices, doping is performed with for n-type regions and for p-type regions, ensuring symmetrical electrical properties across the device. This doping process creates the multi-layer structure—typically a three-layer p-n-p or n-p-n arrangement—that enables bidirectional conduction, with identical doping concentrations in corresponding regions to maintain symmetry. The fabrication process begins with slicing silicon ingots into thin wafers, followed by cleaning and polishing to prepare the surface for doping. Doping is achieved through thermal diffusion, where dopant atoms are introduced via gaseous sources at high temperatures, or , which accelerates ionized dopants into the lattice for more precise control over depth and concentration. After layer formation, metallization is applied to create the two terminal contacts, often using aluminum or other conductive metals deposited via or techniques to ensure low-resistance connections. To protect the device from environmental factors and high-voltage stresses, DIACs are encapsulated in or packages; passivation is commonly used for its and thermal stability, particularly in DO-35 style housings. Final testing focuses on verifying breakdown symmetry by measuring the breakover voltage (V_BO) in both polarities, ensuring the positive and negative thresholds differ by less than a specified tolerance, such as ΔV_BO < 2 V, to confirm reliable bidirectional triggering.

Operating Principles

Breakdown and Triggering Mechanism

The DIAC initiates conduction via avalanche breakdown when the magnitude of the applied voltage reaches the breakover voltage, denoted as VBOV_{BO}. In this process, the electric field intensity across the device's junctions surpasses a critical threshold, causing accelerated carriers—either electrons or holes—to collide with lattice atoms, thereby generating additional electron-hole pairs through impact ionization. This multiplicative carrier generation leads to a sudden surge in conductivity, transitioning the DIAC from a high-impedance blocking state to low-impedance conduction. The device's layered structure ensures bidirectional symmetry, enabling identical avalanche breakdown mechanisms in both forward and reverse polarities without any inherent directional bias. This symmetry arises from the balanced configuration of p-n junctions, which experience equivalent field distributions regardless of voltage polarity, allowing the DIAC to trigger reliably in alternating current applications. Unlike gated devices such as SCRs or TRIACs, the DIAC requires no external control terminal for triggering; conduction is purely voltage-dependent, activated solely by the applied potential exceeding VBOV_{BO}. In certain designs, sensitivity to the rate of voltage rise (dV/dt) is incorporated to suppress unintended triggering from rapid transients or noise. Following breakdown, the DIAC enters a negative differential resistance region, characterized by a sharp voltage drop across the device as current increases, due to the enhanced mobility and density of charge carriers.

Conduction and Turn-Off Behavior

Once triggered by the breakdown mechanism, the DIAC enters its on-state, where it exhibits a low voltage drop of approximately 1.4 V at a forward current of 175 mA, behaving like a low-value resistor that permits substantial current flow through the device. This conduction phase persists as long as the anode current exceeds the holding current IHI_H, typically up to 1.5 mA for devices like the BS08D-112, ensuring stable operation without latching behavior observed in full thyristors like SCRs. Turn-off occurs promptly when the current falls below IHI_H, restoring the DIAC to its high-impedance, blocking state and allowing the voltage across it to rise again for potential re-triggering. Following turn-off, a brief recovery time on the order of microseconds elapses before the device regains full blocking capability, with this delay influenced by factors such as circuit capacitance that affects charge recombination in the semiconductor layers. During the on-state, power dissipation leads to self-heating within the DIAC, necessitating adherence to maximum ratings to prevent thermal runaway or device failure; for instance, typical operating junction temperatures range from -55°C to +125°C, with power dissipation limited to around 450 mW under specified conditions.

Electrical Characteristics

Current-Voltage Curve

The current-voltage (I-V) characteristic of a DIAC is symmetric and bidirectional, exhibiting a distinctive butterfly-shaped curve that reflects its ability to conduct equally in both forward and reverse directions. This symmetry arises from the device's three-layer structure, which ensures identical behavior regardless of voltage polarity. In the plot of current versus voltage, the curve remains in a high-impedance blocking region for applied voltages below the breakover voltage (V_BO), where only a small leakage current flows (max 1-10 μA at 0.5 × V_BO max), corresponding to a high differential resistance (dV/dI > 0). Upon reaching V_BO (typically 28-36 V for devices like the DB3), the DIAC undergoes , initiating a snap-back effect where the voltage across the device abruptly collapses from V_BO to a low on-state voltage of approximately 2-5 V at the breakover current (I_BO, typically <100 μA). This transition marks the entry into the region, characterized by dV/dI < 0, where increasing current leads to a decreasing , enabling rapid switching. The snap-back ensures a sharp trigger action, with the voltage reduction often exceeding 5 V dynamically. Beyond the negative resistance region, the curve enters the forward conduction phase, where the DIAC maintains a low-voltage, high-current state with a nearly constant on-state voltage (less than 3 V) and positive differential resistance, allowing sustained conduction until the current falls below a holding level. The overall shape—high resistance off-state, abrupt snap-back, and low-resistance on-state—facilitates precise triggering in AC circuits. The breakover voltage V_BO exhibits temperature dependence, with a positive temperature coefficient leading to an increase of approximately 0.05-0.1% per °C over typical operating ranges (-40°C to 125°C), resulting in about ±5% variation relative to values. This dependence influences the triggering stability in temperature-varying environments.

Key Performance Parameters

The key performance parameters of DIACs encompass critical electrical and thermal specifications that determine their suitability for triggering and switching applications. These parameters are defined and measured according to established industry standards to ensure reliability and consistency across devices. The breakover voltage (V_BO), also known as the triggering or avalanche breakdown voltage, represents the magnitude of voltage across the DIAC at which it transitions from a high-impedance blocking state to a low-impedance conducting state, typically measured in the forward and reverse directions at a specified temperature (e.g., 25°C). For standard DIACs, V_BO ranges from 20 to 40 V, with devices like the DB3 exhibiting a typical value of 32 V (min 28 V, max 36 V) and the DB4 at 40 V (min 35 V, max 45 V); symmetry between positive and negative polarities is maintained with a maximum difference of 3 V to enable bidirectional operation. The holding current (I_H) is the minimum anode current required to sustain conduction once triggered, below which the DIAC reverts to its blocking state; this parameter is crucial for ensuring stable operation in AC circuits. The on-state voltage (V_TM), or forward voltage drop during conduction, is less than 3 V once activated, reflecting the low-resistance path. Peak surge current (I_TSM) specifies the maximum non-repetitive peak current the DIAC can withstand without damage; for devices like DB3, repetitive peak on-state current is 2 A for short pulses (20 μs). Average power dissipation (P) is limited to 0.15 W to prevent . The operating temperature range spans -40°C to 125°C, accommodating harsh environments while maintaining performance. Reliability testing for these parameters follows JEDEC JESD47 guidelines for stress-test methods on packaged devices, including thermal cycling, high-temperature storage, and , or equivalent IEC procedures for environmental robustness.

Variants and Types

Standard DIACs

Standard DIACs are low-power bidirectional trigger diodes designed primarily for initiating conduction in associated power control devices like triacs, featuring a symmetric p-n-p-n structure that ensures balanced triggering in both positive and negative polarities. This configuration allows the device to remain non-conducting until the applied voltage reaches the breakover threshold, after which it enters a low-voltage conduction state until the current falls below the holding level. Typical models, such as the DB3 series, exhibit a breakover voltage (V_BO) of approximately 30 V, with a nominal value of 32 V (ranging from 28 V to 36 V). Their breakover current is minimal, often not exceeding 50 μA, facilitating precise voltage-based activation without excessive power draw. These devices are commonly housed in compact packages to suit through-hole mounting in control circuits. The DO-35 glass axial package, measuring less than 5 mm in length, provides robust hermetic sealing and is widely used for its thermal stability and small footprint. Alternatively, the plastic package offers similar dimensions under 5 mm and is favored for cost-effective assembly in . Both formats ensure compatibility with automated production while maintaining electrical isolation. A key advantage of standard DIACs lies in their low , typically around $0.10 per unit in volume production, making them ubiquitous in budget-sensitive applications. Their high voltage , with breakover differences limited to 3 V or less between directions, supports accurate phase-angle control in AC circuits by providing consistent triggering points. This minimizes timing errors in oscillatory RC networks used for gate pulsing. However, standard DIACs have limitations that restrict their role to triggering rather than sustained power handling. They are unsuitable for direct load switching due to their low current ratings, typically limited to short pulses under 1 A, beyond which overheating occurs. Additionally, they exhibit sensitivity to rapid voltage changes, necessitating careful circuit design to avoid unintended activation from noise or transients.

SIDACs

SIDACs, or diodes for , are bidirectional voltage-triggered switches constructed from a four-layer p-n-p-n structure, enabling direct AC line switching in higher-power scenarios with breakover voltages (V_BO) ranging from 100 to 500 V and peak non-repetitive surge current (I_TSM) ratings up to 100 A. In contrast to standard DIACs, SIDACs provide superior current-handling capabilities and perform crowbar action to shunt excess voltage for protective purposes. These devices are typically packaged in robust formats such as or axial-leaded types to accommodate power dissipation levels up to 10 , ensuring reliable operation under demanding thermal conditions. Notable examples include the Kxxx series, which exhibit low on-state voltage (typically 1 to 2 V) once triggered, facilitating efficient conduction in power circuits. Their breakdown mechanism resembles that of standard DIACs but is scaled for elevated voltage and current levels.

Applications

Triggering in Power Control Circuits

In power control circuits, the DIAC serves as a symmetric trigger device for thyristors, particularly TRIACs, by generating gate pulses through an RC network to enable adjustable firing angles for AC phase control. This setup allows precise regulation of power delivery to loads, such as varying the conduction angle to control output power from near zero to full load. The symmetric current-voltage characteristics of the DIAC facilitate reliable triggering across both positive and negative AC half-cycles, ensuring balanced operation without the need for separate circuits for each polarity. The basic DIAC-TRIAC dimmer circuit consists of an adjustable resistor (R1), capacitor (C1), the DIAC, and the TRIAC connected in series across the AC supply, with the load in series with the TRIAC. During each AC half-cycle, the capacitor charges through the resistor until the voltage reaches the DIAC's breakover voltage (V_BO), at which point the DIAC conducts rapidly, discharging the capacitor and delivering a sharp pulse to the TRIAC gate to initiate conduction. The firing angle is adjusted by varying R1, which alters the RC time constant and thus the point in the AC cycle when triggering occurs; for instance, conduction can be delayed from 30° (near full power) to 150° (minimum power). This configuration triggers symmetrically in both half-cycles, providing full-wave control suitable for AC loads. Common applications include incandescent lamp dimmers, where the adjustable firing allows smooth control from 5% to 95% of full power, and universal motor soft starters, which delay firing beyond the voltage peak to reduce and enable variable speed operation. These circuits are widely used in household appliances and industrial controls for their straightforward . The primary benefits of DIAC-based triggering in these circuits include simplicity, requiring only four main components without additional transformers or complex drivers, which lowers cost and size. This design operates directly from the AC line, achieving efficiencies exceeding 95% in low-power setups (up to several hundred watts) due to minimal losses in the passive RC network and the DIAC's low holding current.

Overvoltage Protection and Switching

DIACs and SIDACs play crucial roles in through circuits, where they enable rapid response to voltage surges by triggering a across the power line, thereby activating a protective fuse or breaker to isolate the load. In typical AC systems, such as 120 V nominal lines, a SIDAC with a breakover voltage slightly above the peak line voltage (typically 180–250 V) is connected in series with the gate of a silicon-controlled rectifier (SCR) or triac; when an overvoltage transient exceeds this threshold, the SIDAC conducts, firing the SCR to clamp the voltage near zero and divert high current through the fuse, which blows to prevent damage to downstream electronics. SIDACs, with their higher power-handling capabilities compared to standard DIACs, are particularly suited for direct implementation in without additional triggering devices, shunting surge energy away from sensitive circuitry in applications like and industrial controls. For instance, SIDACtor devices limit overvoltages from strikes or crosses to a low clamping voltage (typically 10–40 V), allowing a series fuse to clear the fault after one or more AC cycles by coordinating the SIDAC's on-state current rating with the fuse's time-current characteristics. This coordination ensures the SIDAC survives the initial surge while the fuse interrupts sustained , providing reliable in and SLIC (subscriber line interface circuit) equipment. In switching applications, SIDACs serve as solid-state alternatives to mechanical relays, directly handling AC loads in the 5–20 A range for on/off control in and industrial appliances, leveraging their bidirectional conduction and ability to switch at precise voltage thresholds without for improved reliability and . Representative examples include SIDAC-based transient voltage suppression (TVS) in power supplies for surge clamping during transients, starters in drivers where they initiate gas discharge for illumination, and high-energy pulse generation in gas discharge ignition systems for appliances like stoves and furnaces. These devices exhibit response times below 1 μs—often in the nanosecond range—to effectively mitigate fast transients, with SIDACs offering high surge ratings (e.g., peak pulse currents up to 100 A or more for 8/20 μs waveforms) to absorb energy without failure.

References

  1. https://www.electrical4u.com/diac/
  2. https://www.electronics-tutorials.ws/power/diac.html
  3. https://www.electricaltechnology.org/2021/08/diac.html
  4. https://www.ic-components.com/blog/what-is-diac-symbol%2Coperating-principle%2Cstructure%2Cuses.jsp
  5. https://sites.google.com/site/transistorhistory/Home/us-semiconductor-manufacturers/general-electric-history
  6. https://edisontechcenter.org/semiconductors.html
  7. http://els-journal.etf.unibl.org/journal/Vol14No1/xPaper_01.pdf
  8. https://www.electronics-notes.com/articles/electronic_components/scr/what-is-a-diac.php
  9. https://www.uobabylon.edu.iq/eprints/publication_12_4813_82.pdf
  10. https://www.power-and-beyond.com/diac-the-bidirectional-diode-a-cf8f67bf2849bf2c8a94d15c9610ab81/
  11. https://www.rcet.org.in/uploads/academics/rohini_59315947426.pdf
  12. https://www.waferworld.com/post/the-complete-guide-to-doping-in-semiconductors-what-is-it-and-why-is-it-necessary
  13. https://waferpro.com/everything-you-need-to-know-about-doping-in-silicon-wafers/
  14. https://www.waferworld.com/post/silicon-wafer-processing-two-ways-wafers-can-doped
  15. https://www.renesas.com/en/blogs/semiconductor-device-manufacturing-process-challenges-and-opportunities
  16. https://datasheet.octopart.com/HT40-Littelfuse-datasheet-8220145.pdf
  17. http://class.ece.iastate.edu/ee330/miscHandouts/PowerThyristorApplicationNotes.pdf
  18. https://malabarpoly.com/public/630/202304180350245032-power-electronics-oct--nov-2018---Copy.pdf
  19. https://pdf.digi-electronics.com/pdf/2008/BS08D112-datasheet.pdf
  20. https://www.st.com/resource/en/datasheet/db3.pdf
  21. https://www.st.com/resource/en/application_note/an2703-parameter-list-for-scrs-triacs-ac-switches-and-diacs-stmicroelectronics.pdf
  22. https://www.jedec.org/sites/default/files/docs/JESD47G-01.pdf
  23. https://www.renesas.com/en/document/oth/thyristors-triacs-precautions-use
  24. https://mdesemiconductor.com/what-is-a-thyristor-types-of-thyristors-and-their-uses/
  25. https://www.littelfuse.com/products/overvoltage-protection/sidactor-protection-thyristors
  26. https://www.sicstock.com/products/p4202ac-4202-p4202
  27. https://www.globalspec.com/learnmore/semiconductors/discrete/thyristors/sidacs
  28. https://www.asapsemi.com/blog/diacs-sidacs-a-brief-on-discrete-semiconductor-products/
  29. https://www.littelfuse.com/products/power-semiconductors-control-ics/thyristors-scr-triac/sidac/kxxx1g/k2201g
  30. https://www.littelfuse.com/products/power-semiconductors-control-ics/thyristors-scr-triac/sidac/kxxxzy/k1100g
  31. https://www.littelfuse.com/assetdocs/littelfuse-discrete-thyristors-kxxx0yu-series-datasheet?assetguid=32045fbb-0341-43a4-adb6-e82691f12125
  32. https://www.tayloredge.com/reference/Electronics/Semiconductors/AN1003.pdf
  33. https://www.st.com/resource/en/application_note/an308-triac-analog-control-circuits-for-inductive-loads-stmicroelectronics.pdf
  34. https://www.powersystemsdesign.com/articles/avoiding-field-failures-with-crowbar-protection-thyristors/22/15825
  35. https://www.topdiodes.com/electronics-characteristics-of-sidac/
  36. https://investor.littelfuse.com/news/news-details/2015/Littelfuse-Adds-Two-Unidirectional-SIDAC-Switching-Thyristors-Optimized-for-Capacitor-Discharge-Applications-09-29-2015/default.aspx
Add your contribution
Related Hubs
Contribute something
User Avatar
No comments yet.